Skip to main content
IS 2131:2025 §5.6 · overburden + dilatancy + N₆₀

SPT N-value correction calculator

Corrects field SPT blow counts in the IS 2131:2025 §5.6 order — energy (§5.6.2), overburden C_N (§5.6.3) and dilatancy (§5.6.4) — and averages the design N over the footing’s bearing zone.

Free · no signup · computed in your browser by the engine TerraBrains runs in the app.

Inputs

Illustrative inputs are loaded to demonstrate the method. Replace them with your measured project data before interpreting results.

Keep this calculation

Free here. In TerraBrains this result is saved to the project, carries its clause into a signed report your client can verify, and updates when the borehole does.

Log the borehole this came from — the TerraBrains field app on iPhone, iPad and Android works offline on site and syncs the SPT, samples and layers to the same project.

Worked examples — checked live

Each example comes from a published source. Its inputs run through the same engine as your calculation above; a ✓ means our value is inside the tolerance stated for that example. Load one to see it in the form.

IS 2131:2025 overburden correction C_N at σ′₀ = 50, 100 and 200 kPa

Source: IS 2131:2025, Clause 5.6.3 and Fig. 3 (C_N = 0.77·log10(20·p_a/σ′₀), 0.40 ≤ C_N ≤ 2.0; σ′₀ at SPT depth + 0.30 m)

4/4 within tolerance

Depths are chosen so that σ′₀ at SPT depth + 0.30 m (the 2025 revision's rule) is a round 50 / 100 / 200 kPa with γ = 20 kN/m³ and no water table.

QuantityPublishedOursΔWithin tolerance
σ′₀ at 2.2 + 0.3 m (kPa)50.0050.000.00 %✓
C_N at σ′₀ = 50 kPa1.2401.2340.48 %✓
C_N at σ′₀ = 100 kPa1.0001.0020.20 %✓
C_N at σ′₀ = 200 kPa0.77000.77000.00 %✓

Tolerance: ±0.01 % (Exact: γ·(z + 0.30) = 20 × 2.5.) · ±1.7 % (Read off IS 2131 Fig. 3 at 200 dpi, ±0.02.) · ±2 % (Read off IS 2131 Fig. 3, ±0.02.) · ±2.6 % (Read off IS 2131 Fig. 3, ±0.02.)

Questions engineers ask

In what order are the corrections applied?

In the IS 2131:2025 §5.6 sequence: hammer energy first (§5.6.2, N_E = E_actual/60 · N, off unless you switch it on), then overburden (§5.6.3, C_N bounded 0.40 ≤ C_N ≤ 2.0), then dilatancy (§5.6.4, N″ = 15 + ½(N₁ − 15) for fine sand or silt below the water table when N₁ > 15).

At what depth is the effective stress for C_N taken?

IS 2131:2025 §5.6.3 evaluates σ′₀ at the SPT depth + 0.30 m (the middle of the 300 mm test drive). The “σ′ for C_N evaluated at” input lets you use the stated test depth instead, which is the IS 2131:1981 and textbook convention.

Why are there two design N values?

The overburden-corrected N is the one used for relative density, φ′ and liquefaction. Settlement-based bearing correlations (Terzaghi-Peck, Teng, Meyerhof) were calibrated on field N, so the bearing N keeps the energy and dilatancy corrections but not C_N — overburden-correcting first double-counts depth.

Which overburden correction methods are available?

Peck-Hanson-Thornburn (the IS 2131:2025 form), Liao & Whitman (1986), Skempton (1986) for NC fine, NC coarse and overconsolidated sand, Seed et al. (1975), Kayen et al. (1992) and Bazaraa (1967) — or none.

All ten calculators

Save it, sign it, keep it current.

A free account saves the result to a project with its PDF calculation sheet, and carries the clause into a signed report your client can verify. The same engines run 233 analyses and 47 lab tests inside. 14 days free, no card.