Skip to main content

A finite-element studio for the ground.

Build the section from your boreholes. Stage the construction. Solve in 2-D or 3-D. Check the answer three ways.

14 days free. No card. Runs in your browser.

15soil and rock models
2-D + 3-Dfinite elements
238 of 333finite-element benchmarks reproduced
1–10modellers included, by plan

What you can model.

One studio, one way of working. Draw or import the ground, add the structure, set the phases, solve.

  • Footings

    Load to failure, with the settlement under working load.

    Collapse pressure, circular footing
    227.28 kPapublished 227.64 kPa
  • Embankments

    Built in lifts on soft ground, with consolidation between.

    Factor of safety, 1:2 embankment
    1.54published 1.54
  • Propped excavations

    Walls, props and dewatering, phase by phase.

    Heave of the dug surface
    0.0315 mpublished 0.0315 m
  • Anchored walls

    Prestressed anchors, with the force in each after every phase.

    Force in the top anchor
    500 kNpublished 500 kN
  • Slopes

    Strength reduction, with the slip surface it finds.

    Factor of safety, undrained 2:1 slope
    1.45published 1.47
  • Tunnels

    Volume loss, lining forces and the settlement trough.

    Plastic radius around the opening
    2.60 mpublished 2.58 m
  • Seepage

    Flow nets, phreatic surfaces and uplift.

    Discharge under a cut-off wall
    0.820 m³/day/mpublished 0.818 m³/day/m
  • Site response

    Shaking through the profile, with pore pressure build-up.

    Wave arrival time at the base
    0.101 spublished 0.1 s
  • Footings in 3-D

    Square, rectangular and eccentric loads on a 3‑D mesh.

    Centre settlement, 36 m square load
    161.7 mmpublished 160.2 mm
  • Slopes in 3-D

    The 3‑D slip surface, and how far it differs from the section.


Build it the way it is built.

Walls in, dig, anchor, prestress, dig again. Each stage starts from the one before it, as it does on site. Drag through this one.

7/7Excavate to 20 m, groundwater flow

Largest wall movement

19.3mm

Largest bending moment

142.2kN·m/m

Anchor forces

451 / 1,059kN

Solved by the TerraBrains finite-element solver: the published anchored excavation of the PLAXIS 2D Tutorial Manual (Tutorial 7), built from the studio’s excavation template. The brass line is the left wall, with its movement drawn 60 times larger.


15 soil and rock models.

From a first check to an earthquake analysis in effective stress, in 2-D. Mohr–Coulomb and linear elastic also run in 3-D. Mohr–Coulomb and Hardening Soil can be fitted to your own triaxial tests.

ModelWhat it capturesTypical use
Linear elasticStiffness onlyStructures, stiff rock, first checks
Mohr–CoulombStrength with a constant stiffnessFirst-pass stability and bearing
Hardening SoilStiffness that grows with stress, and unloadingExcavations and walls in sand and stiff clay
HS smallAdds the high stiffness at small strainMovement behind walls and above tunnels
Soft SoilCompression of soft clayEmbankments on soft ground
Soft Soil CreepAdds creep with timeLong-term settlement of soft clay and peat
Modified Cam-ClayCritical-state behaviour of clayNormally consolidated clay
Hoek–BrownStrength of a rock massTunnels and slopes in rock
NGI-ADPUndrained strength that depends on directionStability of soft clay
Jointed RockSliding along joint setsBedded and jointed rock
SANISANDSand from loose to dense with one set of valuesSand under changing density and stress
S-CLAY1SFabric and bonding of natural claySensitive soft clay
Barcelona BasicUnsaturated soil and suctionCompacted fill, collapse on wetting
PM4SandCyclic liquefaction of sandEarthquake analysis in effective stress
PM4SiltCyclic softening of silt and clayEarthquake analysis of fine soils

Three answers to one question.

A factor of safety from one method is a number. The same factor from three methods is an answer.

Finite elements

1.539

Strength reduction

Bounds

1.534–1.542

Lower and upper

Published

1.540

Reference solution

Three independent answers agree.

  • Finite elements

    Strength is reduced until the model fails. The slip surface is found, not assumed.

  • Limit equilibrium

    The method of slices on the same section and the same materials, run for you.

  • Bounds

    A lower and an upper bound from limit analysis. The true answer lies between them.


The classic problems, reproduced.

238 of 333 finite-element benchmark rows agree with an outside reference, from vendor manuals, papers and closed-form solutions; the closed-form engines match 44 of 46 printed worked examples. Six are below; every row is open.

ProblemOursPublishedDifference
Tutorial 1: total force on a rigid footing601 kN588 kN+2.17 %
Tutorial 1: settlement of a flexible footing0.0487 m0.0496 m−1.72 %
Slope with a crest load: factor of safety1.2591.261−0.13 %
Tutorial 7: force in the top anchor500 kN500 kN0.00 %
Tutorial 8: factor of safety, serviceability stage1.481.49−0.48 %
Tutorial 15: vibration amplitude at the surface0.0336 mm0.0339 mm−0.80 %

Published values from the PLAXIS 2D Tutorial Manual. Product names identify the source only.


Included on every plan.

Solo includes 1 modeller, Enterprise 10. Extra modellers are $299 a month. Viewing a model and its results never needs a seat.