| c′ | Effective cohesionStress-independent (true) component of drained shear strength. | kPa | clean sand ~0 · cemented/stiff clay 5–25 | — |
| φ′ | Effective friction angleFrictional component of shear strength in terms of effective stress. | ° | loose sand 28–32 · dense sand 35–45 · clay (drained) 20–28 | — |
| γ | Bulk unit weightTotal weight of soil per unit volume (solids + water). | kN/m³ | sand 16–20 · clay 16–20 · soft clay ~16 | — |
| γ_w | Unit weight of waterTaken as 9.81 kN/m³. | kN/m³ | — | — |
| N_c | Bearing capacity factor (cohesion)Terzaghi/Vesic factor for the cohesion term of bearing capacity; a function of φ. | — | — | — |
| N_q | Bearing capacity factor (surcharge)Factor for the overburden/surcharge term of bearing capacity; a function of φ. | — | — | — |
| N_γ | Bearing capacity factor (self-weight)Factor for the soil self-weight term of bearing capacity; a function of φ. | — | — | — |
| β | Ground slope (footing on a slope)Inclination of the ground surface, measured downwards from the edge of the footing. Reduces bearing capacity through the ground factors g_c, g_q, g_γ (Hansen, Vesić); must not exceed φ.Hansen g_q = g_γ = (1 − 0.5·tan β)⁵ · Vesić g_q = g_γ = (1 − tan β)² | ° | — | Bowles 5e Table 4-5b/c; EN 1997-3:2025 B.4 |
| η | Base tiltInclination of the underside of the footing from horizontal (α in EN 1997-1 Annex D). Reduces bearing capacity through the base factors b_c, b_q, b_γ; loads must then be resolved normal and parallel to the base.Vesić / EC7 b_q = b_γ = (1 − η·tan φ)² · Hansen b_q = exp(−2η·tan φ) | ° | — | Bowles 5e Table 4-5b/c; EN 1997-1:2004 Annex D; EN 1997-3:2025 B.4 |
| g_c, g_q, g_γ | Ground-inclination factorsMultipliers (≤ 1) on the cohesion, surcharge and weight terms for a footing on or at the crest of a slope; 1 on level ground. | — | — | Hansen (1970); Vesić (1975) |
| b_c, b_q, b_γ | Base-inclination factorsMultipliers (≤ 1) on the cohesion, surcharge and weight terms for a tilted footing base; 1 for a horizontal base. | — | — | Hansen (1970); Vesić (1975); EN 1997-1 Annex D |
| q_ult | Ultimate bearing capacityGross pressure at which the soil shears and the foundation fails (general shear). | kPa | — | IS 6403 |
| q_ns | Net safe bearing capacityNet ultimate capacity divided by the factor of safety — the safe net pressure the soil can carry above overburden.q_ns = q_nu / FoS | kPa | — | — |
| q_a | Allowable bearing pressureSafe design pressure — ultimate capacity reduced by a factor of safety and capped by tolerable settlement.q_a = q_u / FoS | kPa | — | — |
| FoS | Factor of safetyResisting capacity ÷ applied demand. The margin against failure. | — | bearing ≥3 · slopes ≥1.3–1.5 · sliding ≥1.5 | — |
| S | SettlementVertical downward movement of the foundation under load — immediate + consolidation + secondary. | mm | — | — |