Interprets a plate load test per IS 1888:1982: zero correction, ultimate pressure from the log-log plot, safe pressure, modulus of subgrade reaction and the settlement of the full-size footing.
Free · no signup · computed in your browser by the engine TerraBrains runs in the app.
Scroll across the table for units, typical values and standards.
Symbol
Full form
Unit
Typical / standard value
Standard
k
Coefficient of permeabilityHow readily water flows through the soil (Darcy). Spans many orders of magnitude with grain size.
m/s
gravel 1e-2 · sand 1e-5 · silt 1e-8 · clay <1e-9
—
S
SettlementVertical downward movement of the foundation under load — immediate + consolidation + secondary.
mm
—
—
q_a
Allowable bearing pressureSafe design pressure — ultimate capacity reduced by a factor of safety and capped by tolerable settlement.q_a = q_u / FoS
kPa
—
—
Tap any unit to convert from it. Unit weight ↔ density uses g = 9.80665 m/s² (γ = ρg).
Inputs
Illustrative inputs are loaded to demonstrate the method. Replace them with your measured project data before interpreting results. The readings are the signed-in page’s illustrative set (IS 1888 itself contains no worked example) — replace them with your test’s first-loading readings.
Keep this calculation
Free here. In TerraBrains this result is saved to the project, carries its clause into a signed report your client can verify, and updates when the borehole does.
Log the borehole this came from — the TerraBrains field app on iPhone, iPad and Android works offline on site and syncs the SPT, samples and layers to the same project.
Worked examples — checked live
Each example comes from a published source. Its inputs run through the same engine as your calculation above; a ✓ means our value is inside the tolerance stated for that example. Load one to see it in the form.
600 mm plate on sand — pressure for 25 mm settlement of a 1.5 m footing (IS 1888 Cl 5.3)
Source: Structville, "How to Determine the Bearing Capacity of Soils from Plate Load Test" (Mar 2021) — S_p = 16 mm for S_f = 25 mm; pressure at 16 mm ≈ 290 kPa (read off the curve)
Pressure at the plate settlement equivalent to 25 mm under the footing (kPa)
290.0
285.7
1.48 %
✓
Tolerance: ±2 % (The source reads 290 kPa off a drawn curve; the engine interpolates linearly between the 200 kPa (10 mm) and 300 kPa (17 mm) readings (285.7 kPa).)
IS 1888 field test PLT-1 — yield value by the log-log method (300 mm plate)
Source: Subrahmanyam, D.S. (National Institute of Rock Mechanics), "Measurements of Bearing Capacity for the Construction of Barrage", Constro Facilitator, 27 Jul 2023 — Tables 4.3–4.6 (readings) and Table 4.7: PLT-1 ultimate 60.17 T/m² (IS 1888:1982 Cl 5.2)
1/1 within tolerance
Pressures are converted from T/m² at 9.80665 kPa. The engine reports the ultimate of the PLATE; the footing value is scaled separately (× B/B_p in sand).
Quantity
Published
Ours
Δ
Within tolerance
Ultimate (yield) pressure of the plate (kPa)
590.1
559.1
5.24 %
✓
Tolerance: ±13 % (The published value is read by eye off a hand-drawn log-log plot (IS 1888 Cl 5.2 gives a graphical construction); the engine's reproducible construction is 5–12 % lower on all four NIRM tests, never higher.)
IS 1888 field test PLT-2 — yield value by the log-log method (300 mm plate)
Source: Subrahmanyam, D.S. (National Institute of Rock Mechanics), "Measurements of Bearing Capacity for the Construction of Barrage", Constro Facilitator, 27 Jul 2023 — Tables 4.3–4.6 (readings) and Table 4.7: PLT-2 ultimate 75.02 T/m² (IS 1888:1982 Cl 5.2)
1/1 within tolerance
Pressures are converted from T/m² at 9.80665 kPa. The engine reports the ultimate of the PLATE; the footing value is scaled separately (× B/B_p in sand).
Quantity
Published
Ours
Δ
Within tolerance
Ultimate (yield) pressure of the plate (kPa)
735.7
684.5
6.95 %
✓
Tolerance: ±13 % (The published value is read by eye off a hand-drawn log-log plot (IS 1888 Cl 5.2 gives a graphical construction); the engine's reproducible construction is 5–12 % lower on all four NIRM tests, never higher.)
IS 1888 field test PLT-3 — yield value by the log-log method (300 mm plate)
Source: Subrahmanyam, D.S. (National Institute of Rock Mechanics), "Measurements of Bearing Capacity for the Construction of Barrage", Constro Facilitator, 27 Jul 2023 — Tables 4.3–4.6 (readings) and Table 4.7: PLT-3 ultimate 70.33 T/m² (IS 1888:1982 Cl 5.2)
1/1 within tolerance
Pressures are converted from T/m² at 9.80665 kPa. The engine reports the ultimate of the PLATE; the footing value is scaled separately (× B/B_p in sand).
Quantity
Published
Ours
Δ
Within tolerance
Ultimate (yield) pressure of the plate (kPa)
689.7
652.9
5.33 %
✓
Tolerance: ±13 % (The published value is read by eye off a hand-drawn log-log plot (IS 1888 Cl 5.2 gives a graphical construction); the engine's reproducible construction is 5–12 % lower on all four NIRM tests, never higher.)
IS 1888 field test PLT-4 — yield value by the log-log method (300 mm plate)
Source: Subrahmanyam, D.S. (National Institute of Rock Mechanics), "Measurements of Bearing Capacity for the Construction of Barrage", Constro Facilitator, 27 Jul 2023 — Tables 4.3–4.6 (readings) and Table 4.7: PLT-4 ultimate 65.02 T/m² (IS 1888:1982 Cl 5.2)
1/1 within tolerance
Pressures are converted from T/m² at 9.80665 kPa. The engine reports the ultimate of the PLATE; the footing value is scaled separately (× B/B_p in sand).
Quantity
Published
Ours
Δ
Within tolerance
Ultimate (yield) pressure of the plate (kPa)
637.6
560.4
12.12 %
✓
Tolerance: ±13 % (The published value is read by eye off a hand-drawn log-log plot (IS 1888 Cl 5.2 gives a graphical construction); the engine's reproducible construction is 5–12 % lower on all four NIRM tests, never higher.)
Questions engineers ask
How is the ultimate pressure picked from the readings?
+
From the intersection of the two straight lines on the log-log load–settlement plot, the IS 1888 method. If the curve has no clear break, a yield point is used; if neither exists, the maximum applied pressure is reported as a lower bound and labelled as such.
How is the plate result scaled to the real footing?
+
For cohesionless soil the settlement is scaled with the B/Bp law S_f = S_p·[B(Bp + 0.3)/(Bp(B + 0.3))]², and the ultimate pressure with B/Bp. For cohesive soil settlement scales with B/Bp and the ultimate pressure is taken equal to the plate’s.
What is the modulus of subgrade reaction here?
+
k = the plate pressure at 1.25 mm settlement ÷ 1.25 mm (IS 9214:1979 Cl 2.3, K = p/0.00125), reported in MPa/m for the plate size tested.
Where does the 25 mm permissible settlement come from?
+
It is the IS 1904:1986 Cl 4.1 value for isolated footings and is only a default — enter your project’s permissible settlement and the pressure at that settlement is recomputed.
A free account saves the result to a project with its PDF calculation sheet, and carries the clause into a signed report your client can verify. The same engines run 233 analyses and 47 lab tests inside. 14 days free, no card.