Sieve analysis calculator — D10, D30, D60, Cu and Cc
Percent passing, the grading curve, D10 / D30 / D60, Cu, Cc and the gravel–sand–fines split from the mass retained on each sieve — IS 2720 (Part 4):1985 and ASTM D6913, on the specimen’s total dry mass.
Free · no signup · computed in your browser by the engine TerraBrains runs in the app.
Scroll across the table for units, typical values and standards.
Symbol
Full form
Unit
Typical / standard value
Standard
D_r
Relative densityHow dense a cohesionless soil is between its loosest and densest states. Controls strength and liquefaction resistance.
Tap any unit to convert from it. Unit weight ↔ density uses g = 9.80665 m/s² (γ = ρg).
Inputs
Illustrative inputs are loaded to demonstrate the method. Replace them with your measured project data before interpreting results. The apertures are the lab form’s IS 2720-4 / ASTM D6913 stack; the masses are illustrative only — replace them with your weighings. A blank mass is a sieve not weighed; enter 0 for an empty sieve.
Keep this calculation
Free here. In TerraBrains this result is saved to the project, carries its clause into a signed report your client can verify, and updates when the borehole does.
Log the borehole this came from — the TerraBrains field app on iPhone, iPad and Android works offline on site and syncs the SPT, samples and layers to the same project.
Worked examples — checked live
Each example comes from a published source. Its inputs run through the same engine as your calculation above; a ✓ means our value is inside the tolerance stated for that example. Load one to see it in the form.
200 g sand — retained masses on eight sieves to percent passing
Source: FHWA NHI-06-088, Soils and Foundations Reference Manual Vol. I (2006), Fig. 5-2 "Example grain size distribution based on sieve analysis (Jumikis, 1962)", p. 5-14
7/7 within tolerance
The pan (3.40 g) is not entered as a row: with the total dry mass of 200.0 g given, whatever is not retained on a sieve is the fines.
Quantity
Published
Ours
Δ
Within tolerance
% passing No. 10 (2.00 mm) (%)
98.58
98.58
0.00 %
✓
% passing No. 20 (0.850 mm) (%)
95.75
95.75
0.00 %
✓
% passing No. 40 (0.425 mm) (%)
72.72
72.73
0.01 %
✓
% passing No. 60 (0.250 mm) (%)
50.73
50.73
0.00 %
✓
% passing No. 100 (0.150 mm) (%)
38.91
38.91
0.00 %
✓
% passing No. 140 (0.106 mm) (%)
33.28
33.28
0.00 %
✓
% passing No. 200 (75 µm) — fines (%)
1.700
1.700
0.00 %
✓
Tolerance: ±0.02 % (Printed to 2 dp.) · ±0.02 % (Printed to 2 dp; the table rounds each sieve's % retained before accumulating (72.725 → 72.72).) · ±0.03 % (Printed to 2 dp.) · ±0.6 % (Printed to 2 dp (1.70); the pan holds 3.40 g of 200 g.)
Gravel / sand / fines split from percent passing — clayey sand with gravel
Source: Das, B.M., Principles of Foundation Engineering (Cengage), Example 2.9 — passing No. 4 = 82 %, No. 200 = 41 % ⇒ gravel 18 %, sand 41 %
3/3 within tolerance
Das gives percent passing (No. 4 82, No. 10 71, No. 40 64, No. 200 41); they are entered as masses retained on a 100 g specimen (18, 11, 7, 23 g). This checks the mass-basis bookkeeping and the fraction boundaries, not a new reduction.
Clean sand with 5 % fines — sand vs gravel and the fines that make it borderline
Source: Holtz, R.D. & Kovacs, W.D., An Introduction to Geotechnical Engineering (Prentice-Hall), Example 3.1, soil 2 — 97 % passes No. 4, 5 % passes No. 200
3/3 within tolerance
H&K's % finer (97, 90, 40, 8, 5) entered as masses on a 100 g specimen. H&K read D60 = 0.71, D30 = 0.34, D10 = 0.18 mm off a smooth curve; the calculator interpolates log-linearly between sieves (0.79 / 0.31 / 0.16 mm) — see the file header.
IS 2720 (Part 4):1985 and ASTM D6913 put every percentage on the oven-dry mass of the whole specimen, so whatever passed the finest sieve (the pan plus any wash loss) counts as fines. Without it the fines fraction is unknown. If you only weighed the pan, enter the pan mass instead.
How are D10, D30 and D60 interpolated?
+
Log-linearly in particle size between the two sieves that bracket 10, 30 and 60 % passing. If the curve does not reach a percentage, that D-value is shown as “—” rather than extrapolated.
When is a soil reported well-graded?
+
Per ASTM D2487: a sand needs Cu ≥ 6 and a gravel Cu ≥ 4, both with 1 ≤ Cc ≤ 3. The soil is treated as a gravel when less than 50 % passes the 4.75 mm sieve.
What are the fraction boundaries?
+
Gravel is coarser than 4.75 mm, sand is 4.75 mm to 75 µm (coarse 4.75–2.0, medium 2.0–0.425, fine 0.425–0.075 mm) and fines pass 75 µm — the IS 1498 / IS 2720-4 boundaries.
A free account saves the result to a project with its PDF calculation sheet, and carries the clause into a signed report your client can verify. The same engines run 233 analyses and 47 lab tests inside. 14 days free, no card.