Every comparison we hold, by analysis, deviations first.
For a checking engineer or reviewer deciding whether a number can be trusted without re-running it elsewhere: each row gives the source and page, the published or closed-form value, our value, the miss and the status the registry records. A deviation is reported as a measured difference, with its reason, ahead of everything else.
Suites last run on 2026-11-14 at commit 77a6712437, Node 22.18.0. 1 suite(s) were edited after that run and are marked. Generated from the repository; the files below and this page come from the same generator.
Finite-element rows by what they are compared against: 224 a published or analytical reference, 42 a vendor-published value, 53 self-checks (compared with something derived inside this project, so counted separately), 14 with no reference value recorded. Finite-element rows by status: 280 pass, 35 deviation, 6 recorded, no published value, 8 superseded, 4 pending. Recorded, no published value: We ran the case, but the source publishes no number to compare with, so there is no verdict. Superseded: An older stand-in or umbrella row, replaced by the newer row or rows named on it. It is not counted as a pass or as open. Pending: The case can be run with the solver as it is, and has not been run yet. The closed-form engine registry holds 46 published problems: 44 pass, 2 miss.
Where our results differ from the reference
Every finite-element row that is not a pass (53; superseded rows and rows recorded with no published value are included, and say so in their status), every closed-form miss (2) and every suite test block that failed in the recorded run (0). Miss = (ours − reference) / reference, against the closed form or printed value where one exists, otherwise against the vendor’s published value.
Showing 53 of 53 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
mesh-refinement study of the case-A force 2π·|Force-Y| (full Newton, tol 1e-8, tension cut-off on) plaxis-2d-tut1-a-refinement · Footings and bearing capacity | T15: (542 el (re 1.2): 596.65; 1201 el (re 0.8): running at report time; 2132 el (re 0.6): did not converge: load advan… | 588kN | — | Ours T15: (542 el (re 1.2): 596.65; 1201 el (… kNPublished 588 kN— | Deviation | |
| ||||||
settlement under the strip (PLAXIS 2D 0.04845 / 0.04965 m; Gibson 0.05) plaxis-verif-gibson-2011-a · Footings and bearing capacity | 0.04599m | 0.05m | −8.02 % | Ours 0.04599 mPublished 0.05 m−8.02 % | Deviation | |
| ||||||
plaxis-verif-k5-set plaxis-verif-k5-set · Finite-element meshing, solvers and procedures | — | — | — | Ours —Published —— | Superseded | |
| ||||||
plaxis-verif-v2-set plaxis-verif-v2-set · Finite-element meshing, solvers and procedures | — | — | — | Ours —Published —— | Superseded | |
| ||||||
maximum bending moment in the wall, final excavation (−6 m), characteristic parameters, embedment 4 m ertc7-wall-moment · Retaining walls, excavations and structural elements | 204kNm/m | 212kNm/m | −3.77 % | Ours 204 kNm/mPublished 212 kNm/m−3.77 % | Deviation | |
| ||||||
strut force, final excavation ertc7-strut-force · Retaining walls, excavations and structural elements | 123.9kN/m | 117kN/m | +5.90 % | Ours 123.9 kN/mPublished 117 kN/m+5.90 % | Deviation | |
| ||||||
horizontal displacement of the wall base, final excavation ertc7-wall-base-displacement · Retaining walls, excavations and structural elements | 9mm | 6mm | +50.0 % | Ours 9 mmPublished 6 mm+50.0 % | Deviation | |
| ||||||
drained / undrained embankment + safety factor plaxis-2d-tut2 · Slopes and embankments — factor of safety | — | — | — | Ours —Published —— | Superseded | |
| ||||||
|u| at (50, 10) at the end of each phase (submerged excavation, undrained-A clay) plaxis-2d-tut3 · Retaining walls, excavations and structural elements | phase1: 0.0092; phase2: 0.0302; phase3: 0.0302; phase4: 0.074; phase5: stops at ΣMstage 0.350 (tol 1e-8 and 1e-7); at t… | phase1: 0.005; phase2: 0.024; phase3: 0.024; phase4: 0.057; phase5: 0.141 | — | Ours phase1: 0.0092; phase2: 0.0302; phase3: … mPublished phase1: 0.005; phase2: 0.024; phase3: 0.… m— | Superseded | |
| ||||||
final phase: wall max |M|, anchor forces, wall displacements plaxis-2d-tut7-final · Retaining walls, excavations and structural elements | wallL Mmax: 154; wallR Mmax: 157; at y: 23; anchors top L/R: [430.4, 428.6]; anchors bottom L/R: [1053.4, 1050.8]; ux(4… | — | — | Ours wallL Mmax: 154; wallR Mmax: 157; at y: …Published —— | Superseded | |
| ||||||
final phase with REAL phase-6 steady flow: wall max |M|, anchor forces, wall displacements plaxis-2d-tut7-final-k4-flow · Retaining walls, excavations and structural elements | wallL Mmax: 167; wallR Mmax: 170.7; at y: 23; anchors top L/R: [420.1, 424.4]; anchors bottom L/R: [1081.6, 1081.8]; ux… | — | — | Ours wallL Mmax: 167; wallR Mmax: 170.7; at y…Published —— | Superseded | |
| ||||||
SR-FELA factor of safety, lower / upper bound (ACADS 1(d), kh = 0.15) k5c-acads-1d-fela-bounds · Slopes and embankments — factor of safety | lower: 0.9669; upper: 0.9767; errorPct: 0.51 | 1.039 | −6.47 % | Ours lower: 0.9669; upper: 0.9767; errorPct: …Published 1.039−6.47 % | Deviation | |
| ||||||
Tutorial 9 (Soft Soil undrained A + HS, 4 consolidation phases): time to p_excess < 1 kPa, plus settlements / excess pore pressures per phase k5b-plaxis-2d-tut9-consolidation-time · Settlement, stress distribution and consolidation | t at p_excess < 1 kPa (d): 38.69; settlement (0,0) mm P1/P2/P3/P4: [261.4, 664.5, 829.5, 1033.7]; max p_excess kPa P1/P… | > 50 d | — | Ours t at p_excess < 1 kPa (d): 38.69; settle…Published > 50 d— | Superseded | |
| ||||||
Tutorial 7 with the REAL Hardening Soil (Table 7-1) + phase-6 steady flow: anchor forces, wall max |M|, wall ux k5b-plaxis-2d-tut7-real-hs · Retaining walls, excavations and structural elements | prestress P3 / P5: [500, 1000]; final anchors top L/R: [450.6, 446.8]; final anchors bottom L/R: [1058.8, 1055.4]; wall… | prestress 500 / 1000 kN (figures otherwise) | — | Ours prestress P3 / P5: [500, 1000]; final an…Published prestress 500 / 1000 kN (figures otherwi…— | Recorded, no published value | |
| ||||||
Tutorial 2, embankment on DRAINED HS clay: uy at the crest (23,4), centre base (25,0), 2 m beyond the toe (38,0) k5b-plaxis-2d-tut2-drained · Slopes and embankments — factor of safety | crest: -226.7; centre base: -177.9; beyond toe (38,0): 0.6 | —mm | — | Ours crest: -226.7; centre base: -177.9; beyo… mmPublished — mm— | Recorded, no published value | |
| ||||||
factor of safety, homogeneous 2:1 slope, φ′ 20°, c′/γH 0.05, ψ 0, D = 1 k5a-gl99-example1 · Slopes and embankments — factor of safety | 1.3412 | 1.35 | −0.65 % | Ours 1.3412Published 1.35−0.65 % | Deviation | |
| ||||||
factor of safety ΣMsf, embankment on undrained (A) clay (Phase 4) k5a-tut2-safety-undrained · Slopes and embankments — factor of safety | 1.14911 | 1.4 | −17.9 % | Ours 1.14911Published 1.4−17.9 % | Superseded | |
| ||||||
|u| at (50, 10) at the end of each phase — real Hardening Soil, the kernel's own submerged excavation (D90: deactivated clusters keep their water) k5d-plaxis-2d-tut3-submerged-hs · Retaining walls, excavations and structural elements | phase1: 0.0054; phase2: 0.0225; phase3: 0.0225; phase4: 0.0589; phase5: 0.1519 | phase1: 0.0062; phase2: 0.0242; phase3: 0.0242; phase4: 0.0572; phase5: 0.1417 | phase1: -12.9; phase2: -7; phase3: -7; phase4: 3; phase5: 7.2 % | Ours phase1: 0.0054; phase2: 0.0225; phase3: … mPublished phase1: 0.0062; phase2: 0.0242; phase3: … mphase1: -12.9; phase2: -7; phase3: -7; p… | Deviation | |
| ||||||
Tutorial 10: Tutorial 7 (real HS) + two extraction wells in the phase-6 steady flow (1.5 m³/day/m, h_min 17 m): well discharges, groundwater head in the pit, final anchor forces / wall moments k5d-plaxis-2d-tut10-dewatering · Retaining walls, excavations and structural elements | well discharge each (m³/day/m): -0.9797; side inflow each: 0.9773; pit-bottom seepage: 0; head in the pit (m): 18.90–18… | figures only (head lowered in the excavation, flow to the wells) | — | Ours well discharge each (m³/day/m): -0.9797;…Published figures only (head lowered in the excava…— | Recorded, no published value | |
| ||||||
SCMEP soft-clay embankment, Soft Soil (USTUTT set): centreline settlement after undrained construction / after 100 years, p_excess at (0, −2.5) k5d-benchmark-embankment-soft-clay · Slopes and embankments — factor of safety | tol 1e-8 (530 T15, 9 Nov 2026): after the D557 mesh change layer 1 stops at ΣMstage 0.8515 (92 steps); settlement (0,0)… | other models after construction: 0.11–0.24 m; after 100 years: 1.10–1.60 m | — | Ours tol 1e-8 (530 T15, 9 Nov 2026): after th… m, kPaPublished other models after construction: 0.11–0.… m, kPa— | Deviation | |
| ||||||
|u| at (40, 27) at the end of ULS phase 12 (real Hardening Soil, DA3) k5d1-plaxis-2d-tut8-uls-displacement · Retaining walls, excavations and structural elements | 0.069m | 0.0518m | +33.2 % | Ours 0.069 mPublished 0.0518 m+33.2 % | Deviation | |
| ||||||
NATM tunnel, β-method (60 % / 100 %) in two excavation stages: crown settlement, lining forces k5d1-plaxis-2d-tut6-natm · Tunnels and underground works | crown uy phase 1..4 mm: [-7.45, -8.65, -9.17, -9.11]; crest (−7, 35) uy phase 4 mm: -19.77; liningTop M max/min kNm/m:… | — | — | Ours crown uy phase 1..4 mm: [-7.45, -8.65, -…Published —— | Recorded, no published value | |
| ||||||
building tilt at the end of phase 5 (lining), displacements from phase 2 on: (uy(15, 3) − uy(5, 3)) / 10 m k5d1-plaxis-2d-tut5-building-tilt · Tunnels and underground works | 0.1834% | 0.168% | +9.17 % | Ours 0.1834 %Published 0.168 %+9.17 % | Deviation | |
| ||||||
ΣMsf of the Safety phase after the second excavation (phase 3) k5d1-plaxis-2d-tut4-safety-phase7 · Slopes and embankments — factor of safety | — | 1.33 | — | Ours —Published 1.33— | Deviation | |
| ||||||
ΣMsf of the Safety phase after the wall and backfill (phase 6) k5d1-plaxis-2d-tut4-safety-phase8 · Slopes and embankments — factor of safety | — | 1.83 | — | Ours —Published 1.83— | Deviation | |
| ||||||
ΣMsf of the Safety phase after the second excavation (phase 3) — PLAXIS-REPRODUCTION variant (cable strength per metre, reduced in Safety; PLAXIS-parity convergence) alg1-plaxis-2d-tut4-repro-safety-phase7 · Slopes and embankments — factor of safety | 1.2852 | 1.33 | −3.37 % | Ours 1.2852Published 1.33−3.37 % | Deviation | |
| ||||||
ΣMsf of the Safety phase after the wall and backfill (phase 6) — PLAXIS-REPRODUCTION variant (cable strength per metre, reduced in Safety; PLAXIS-parity convergence) alg1-plaxis-2d-tut4-repro-safety-phase8 · Slopes and embankments — factor of safety | 1.6625 | 1.83 | −9.15 % | Ours 1.6625Published 1.83−9.15 % | Deviation | |
| ||||||
first two natural frequencies of a dam with depth-varying G (PLAXIS 2.9 / 6.4 Hz; closed form 3.1 / 7.0 Hz) k7a-dam-free-vibration · Earthquake engineering, dynamics and liquefaction | —Hz | 3.1Hz | — | Ours — HzPublished 3.1 Hz— | Pending | |
| ||||||
surface deflection under a pulse load on a 3-layer pavement (stiff / soft subgrade) k7a-pulse-multilayer · Earthquake engineering, dynamics and liquefaction | —mm | —mm | — | Ours — mmPublished — mm— | Pending | |
| ||||||
surface-wave amplitude vs distance from a harmonic prescribed displacement (BEM Chouw et al. 1991) k7a-surface-waves · Earthquake engineering, dynamics and liquefaction | —m | —m | — | Ours — mPublished — m— | Pending | |
| ||||||
Midas GTS NX dynamics benchmarks k7a-midas-ch4-dynamics · Earthquake engineering, dynamics and liquefaction | — | — | — | Ours —Published —— | Pending | |
| ||||||
max r_u = Δp/σ′v0 at 4 m and 7 m depth k7b-liquefaction-column-ru · Earthquake engineering, dynamics and liquefaction · Self-check | 4 m: 0.8024; 7 m: 1.0311 | 0.95 | — | Ours 4 m: 0.8024; 7 m: 1.0311Published 0.95— | Deviation | |
| ||||||
residual surface displacement after the generator stops, r = 1.37 m, no damping (amplitude over 0.6–1.0 s) k7-plaxis-2d-tut15-free-vibration-residual-undamped · Earthquake engineering, dynamics and liquefaction | 0.00531mm | 0.0034mm | +56.2 % | Ours 0.00531 mmPublished 0.0034 mm+56.2 % | Deviation | |
| ||||||
residual surface displacement after the generator stops, r = 1.37 m, with Rayleigh damping (amplitude over 0.6–1.0 s) k7-plaxis-2d-tut15-free-vibration-residual-damped · Earthquake engineering, dynamics and liquefaction | 0.00313mm | 0.0008mm | +291.3 % | Ours 0.00313 mmPublished 0.0008 mm+291.3 % | Deviation | |
| ||||||
HS-1 εv medium (drained TC, MMM Fig 13.3): max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-1 · Constitutive models and element tests · Self-check | 2.452 | 1 | — | Ours 2.452Published 1— | Deviation | |
| ||||||
HS-1 εv dense: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-2 · Constitutive models and element tests · Self-check | 1.347 | 1 | — | Ours 1.347Published 1— | Deviation | |
| ||||||
HS-4 εv dense (Hostun): max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-3 · Constitutive models and element tests · Self-check | 1.001 | 1 | — | Ours 1.001Published 1— | Deviation | |
| ||||||
HS-2 q medium (undrained): max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-4 · Constitutive models and element tests · Self-check | 3.595 | 1 | — | Ours 3.595Published 1— | Deviation | |
| ||||||
HS-2 q dense: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-5 · Constitutive models and element tests · Self-check | 3.704 | 1 | — | Ours 3.704Published 1— | Deviation | |
| ||||||
HS-2 P_excess medium: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-6 · Constitutive models and element tests · Self-check | 1.334 | 1 | — | Ours 1.334Published 1— | Deviation | |
| ||||||
HS-2 P_excess dense: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-7 · Constitutive models and element tests · Self-check | 7.456 | 1 | — | Ours 7.456Published 1— | Deviation | |
| ||||||
HSS-1 G dense σ3 100 kPa (Benz 2007 Fig 8.2/8.3): max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-8 · Constitutive models and element tests · Self-check | 1.562 | 1 | — | Ours 1.562Published 1— | Deviation | |
| ||||||
HSS-1 G loose σ3 100 kPa: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-9 · Constitutive models and element tests · Self-check | 2.765 | 1 | — | Ours 2.765Published 1— | Deviation | |
| ||||||
flexible control: footprint-corner settlement (x = y = 18 m) under 66 kPa surface pressure (elastic clay) k11-3d-tut1-a-control-corner · Three-dimensional analysis | 50.08mm | 45.14mm | +10.9 % | Ours 50.08 mmPublished 45.14 mm+10.9 % | Deviation | |
| ||||||
Tutorial 1 Case A as written (Table 1–1 Mohr–Coulomb clay): mean settlement of the basement underside (z = −2 m), base mesh k11-3d-tut1-a-basement-settlement · Three-dimensional analysis | 99.23mm | 115.38mm | −14.0 % | Ours 99.23 mmPublished 115.38 mm−14.0 % | Deviation | |
| ||||||
Tutorial 1 Case A as written: mean basement-underside settlement, bisected mesh k11-3d-tut1-a-basement-settlement-fine · Three-dimensional analysis · Self-check | 102.19mm | 115.38mm | −11.4 % | Ours 102.19 mmPublished 115.38 mm−11.4 % | Deviation | |
| ||||||
Tutorial 1 Case A with the clay as Hardening Soil: mean settlement of the basement underside (z = −2 m), base mesh k11-3d-hs-tut1-basement · Three-dimensional analysis | 75.228mm | —mm | — | Ours 75.228 mmPublished — mm— | Recorded, no published value | |
| ||||||
Tutorial 1 Case A: HS basement settlement relative to the Mohr–Coulomb run (row k11-3d-tut1-a-basement-settlement, 99.231 mm) k11-3d-hs-tut1-vs-mc · Three-dimensional analysis | -24.19% | —% | — | Ours -24.19 %Published — %— | Recorded, no published value | |
| ||||||
NorSand drained plane strain (Cornforth apparatus, sigma_3 = 276 kPa, eps_2 = 0, K0 start), Brasted sand, loose (test A10-14): peak major principal stress sigma_1 m17-norsand-brasted-plane-strain-peak-loose · Constitutive models and element tests | 1100kPa | 1033kPa | +6.50 % | Ours 1100 kPaPublished 1033 kPa+6.50 % | Deviation | |
| ||||||
NorSand drained plane strain (Cornforth apparatus, sigma_3 = 276 kPa, eps_2 = 0, K0 start), Brasted sand, compact (test A10-12): peak major principal stress sigma_1 m17-norsand-brasted-plane-strain-peak-compact · Constitutive models and element tests | 1303kPa | 1186kPa | +9.90 % | Ours 1303 kPaPublished 1186 kPa+9.90 % | Deviation | |
| ||||||
NorSand drained plane strain (Cornforth apparatus, sigma_3 = 276 kPa, eps_2 = 0, K0 start), Brasted sand, dense (test A10-17): peak major principal stress sigma_1 m17-norsand-brasted-plane-strain-peak-dense · Constitutive models and element tests | 1646kPa | 1488kPa | +10.6 % | Ours 1646 kPaPublished 1488 kPa+10.6 % | Deviation | |
| ||||||
maximum settlement at ground level after phase 5 (PLAXIS: horizontal cross-section at z = 1.95 m; ours: surface z = 2 m) tunnel-s1-plaxis3d-tut5-ground-settlement · Tunnels and underground works | 1.8549cm | 1.9cm | −2.37 % | Ours 1.8549 cmPublished 1.9 cm−2.37 % | Deviation | |
| ||||||
maximum vertical displacement after phase 5 (Fig 5-34 caption) tunnel-s1-plaxis3d-tut5-max-uz · Tunnels and underground works | 3.4275cm | 3.1cm | +10.6 % | Ours 3.4275 cmPublished 3.1 cm+10.6 % | Deviation | |
| ||||||
| Problem | Ours | Published | Difference | Tolerance | Status | Details | |
|---|---|---|---|---|---|---|---|
N_γ strip on cohesionless sand, smooth (c = 0, q = 0) FE-NGAMMA-SMOOTH | 415.506kPa | 612.24kPa | −32.1 % | ± 1 % | Ours 415.506 kPaPublished 612.24 kPa−32.1 % | Miss | |
| |||||||
N_γ strip on cohesionless sand, rough (c = 0, q = 0) FE-NGAMMA-ROUGH | 1249.39kPa | 1180.34kPa | +5.85 % | ± 1 % | Ours 1249.39 kPaPublished 1180.34 kPa+5.85 % | Miss | |
| |||||||
Suite test blocks that failed
None in the recorded run.
Suite test blocks written but not asserted
- fe-slope-stability-web-validation[VAL-1] ACADS 1(a): FE strength-reduction FoS within 3 % of RS2 SSR 0.99Why: VAL1-FE-1: RS2 SSR 0.99 (critical SRF 0.995) is above the rigorous upper bound 0.984, so a 3 % band around it is not a correctness criterion. Default is 0.9609 after VAL1-FE-2 (was 0.9453, 4.5 % low). See MEDIUM-ACADS-REPORT.md / MEDIUM-D612-REPORT.md
- footing-3d-web-validationC.FOOT3D.6h: c-φ square with γ and D_f — physical bounds and its D509 lock (HEAVY tier)Why: GEOTECH_HEAVY=1 (minutes in TS; the Python twin runs it in validate_fe_footing_3d.py)
Footings and bearing capacity
17 finite-element rows (2 deviations) · 40 closed-form problems · 32 validation suites
Finite-element solver registry
Showing 17 of 17 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
total footing force 2π·|Force-Y| at 0.05 m indentation (rigid rough footing, case A) plaxis-2d-tut1-a-force | 600.77kN | 588kN | +2.17 % | Ours 600.77 kNPublished 588 kN+2.17 % | Pass | |
| ||||||
Force-Y per radian at ΣMstage = 0.3943 (u = 0.0197 m) plaxis-2d-tut1-a-fy-0.3943 | -53.974kN/rad | -53.79kN/rad | +0.34 % | Ours -53.974 kN/radPublished -53.79 kN/rad+0.34 % | Pass | |
| ||||||
maximum total displacement (the footing) plaxis-2d-tut1-a-umax | 0.05m | 0.05m | 0.00 % | Ours 0.05 mPublished 0.05 m0.00 % | Pass | |
| ||||||
K0 procedure: σ′v = −Σγh + p, σ′h = 0.5 σ′v, p = 10(2 − y) — worst |error| over every integration point plaxis-2d-tut1-k0-effective-stress · Self-check | 1.000e-12kPa | hand calculation (γ_unsat 17 above y = 2, γ_sat 20 below, γ_w 10, K0 = 1 − sin 30° = 0.5) | 0.00 % | Ours 1.000e-12 kPaPublished hand calculation (γ_unsat 17 above y = 2… kPa0.00 % | Pass | |
| ||||||
|u| of node (0, 4) vs ΣMstage under 188 kPa on the plate footing (EA 5e6, EI 8.5e3, ν 0), axisymmetric; PLAXIS Figure 1–27: 0.5 → 0.0156, 0.6 → 0.0207, 0.8 → 0.0328, 0.9 → 0.0398, 1.0 → 0.0496 m (±0.0003) plaxis-2d-tut1-b-flexible | 0.048745m | 0.0496m | −1.72 % | Ours 0.048745 mPublished 0.0496 m−1.72 % | Pass | |
| ||||||
mesh-refinement study of the case-A force 2π·|Force-Y| (full Newton, tol 1e-8, tension cut-off on) plaxis-2d-tut1-a-refinement | T15: (542 el (re 1.2): 596.65; 1201 el (re 0.8): running at report time; 2132 el (re 0.6): did not converge: load advan… | 588kN | — | Ours T15: (542 el (re 1.2): 596.65; 1201 el (… kNPublished 588 kN— | Deviation | |
| ||||||
collapse average stress p = 2πF/(πR²) of a smooth rigid circular footing plaxis-verif-circular-footing-cox | 227.284kPa | 225.6kPa | +0.75 % | Ours 227.284 kPaPublished 225.6 kPa+0.75 % | Pass | |
| ||||||
footing force for 0.01 m plaxis-verif-smooth-rigid-strip | 15.225kN/m | 15.148kN/m | +0.51 % | Ours 15.225 kN/mPublished 15.148 kN/m+0.51 % | Pass | |
| ||||||
centre settlement plaxis-verif-boussinesq | 0.09033mm | 0.091mm | −0.73 % | Ours 0.09033 mmPublished 0.091 mm−0.73 % | Pass | |
| ||||||
mean ultimate stress, smooth / rough (PLAXIS 2D 7.831 / 9.168 kPa) plaxis-verif-davis-booker | 7.8335 / 9.1826 | 7.800 / 9.090 | +0.43 / +1.02 % | Ours 7.8335 / 9.1826 kPaPublished 7.800 / 9.090 kPa+0.43 / +1.02 % | Pass | |
| ||||||
settlement under the strip (PLAXIS 2D 0.04845 / 0.04965 m; Gibson 0.05) plaxis-verif-gibson | 0.04951m | 0.05m | −0.98 % | Ours 0.04951 mPublished 0.05 m−0.98 % | Pass | |
| ||||||
settlement under the strip (PLAXIS 2D 0.04845 / 0.04965 m; Gibson 0.05) plaxis-verif-gibson-2011-a | 0.04599m | 0.05m | −8.02 % | Ours 0.04599 mPublished 0.05 m−8.02 % | Deviation | |
| ||||||
strip footing bearing factor bounds: Prandtl Nc smooth k5c-strip-prandtl-nc-smooth | lower: 5.1256; upper: 5.1455; errorPct: 0.19 | 5.14159 | — | Ours lower: 5.1256; upper: 5.1455; errorPct: …Published 5.14159— | Pass | |
| ||||||
strip footing bearing factor bounds: Prandtl Nc rough k5c-strip-prandtl-nc-rough | lower: 5.1322; upper: 5.1551; errorPct: 0.22 | 5.14159 | — | Ours lower: 5.1322; upper: 5.1551; errorPct: …Published 5.14159— | Pass | |
| ||||||
strip footing bearing factor bounds: Ngamma smooth 30 (Martin 7.65300) k5c-strip-ngamma-smooth-30 | lower: 7.374; upper: 8.2657; errorPct: 5.7 | 7.653 | — | Ours lower: 7.374; upper: 8.2657; errorPct: 5…Published 7.653— | Pass | |
| ||||||
strip footing bearing factor bounds: Ngamma rough 30 (Martin 14.7543) k5c-strip-ngamma-rough-30 | lower: 13.7698; upper: 15.9087; errorPct: 7.21 | 14.7543 | — | Ours lower: 13.7698; upper: 15.9087; errorPct…Published 14.7543— | Pass | |
| ||||||
strength-reduction factor of a strip load q = (2 + π)c/2 on weightless Tresca (closed form F = 2) k5a-prandtl-safety | 2.00312 | 2 | +0.16 % | Ours 2.00312Published 2+0.16 % | Pass | |
| ||||||
Closed-form engine registry
Showing 40 of 40 rows.
| Problem | Ours | Published | Difference | Tolerance | Status | Details | |
|---|---|---|---|---|---|---|---|
EN 1997-1 Annex D Nq at φ′d = 38° (M1) BC-JRC-A33-NQ-M1 | 48.9333 | 48.87 | +0.13 % | ± 0.3 % | Ours 48.9333Published 48.87+0.13 % | Pass | |
| |||||||
EN 1997-1 Annex D Nγ at φ′d = 38° (M1) BC-JRC-A33-NG-M1 | 74.8991 | 74.8 | +0.13 % | ± 0.3 % | Ours 74.8991Published 74.8+0.13 % | Pass | |
| |||||||
EN 1997-1 Annex D Nq at φ′d = tan⁻¹(tan 38°/1.25) (M2) BC-JRC-A33-NQ-M2 | 23.1946 | 23.17 | +0.11 % | ± 0.3 % | Ours 23.1946Published 23.17+0.11 % | Pass | |
| |||||||
EN 1997-1 Annex D Nγ at φ′d (M2) BC-JRC-A33-NG-M2 | 27.7445 | 27.72 | +0.09 % | ± 0.3 % | Ours 27.7445Published 27.72+0.09 % | Pass | |
| |||||||
Terzaghi, square footing — cohesion + surcharge terms (the Nγ term is a convention comparison, not reproduced) BC-DAS-4.1 | 968.329kPa | 968.2kPa | +0.01 % | ± 0.5 % | Ours 968.329 kPaPublished 968.2 kPa+0.01 % | Pass | |
| |||||||
General bearing equation, same footing BC-DAS-4.3 | 1374kPa | 1373.2kPa | +0.06 % | ± 0.5 % | Ours 1374 kPaPublished 1373.2 kPa+0.06 % | Pass | |
| |||||||
Inclined load β = 20° BC-DAS-4.5 | 273.801kPa | 273.66kPa | +0.05 % | ± 0.5 % | Ours 273.801 kPaPublished 273.66 kPa+0.05 % | Pass | |
| |||||||
Eccentric strip, e = 0.2 m BC-DAS-4.7 | 3288.22kPa | 3287.39kPa | +0.03 % | ± 0.5 % | Ours 3288.22 kPaPublished 3287.39 kPa+0.03 % | Pass | |
| |||||||
Eccentric + inclined strip BC-DAS-4.12 | 461.671kPa | 461.98kPa | −0.07 % | ± 0.5 % | Ours 461.671 kPaPublished 461.98 kPa−0.07 % | Pass | |
| |||||||
Case study — Bozozuk silo, φ = 0 BC-DAS-SILO | 182.503kPa | 181.8kPa | +0.39 % | ± 0.5 % | Ours 182.503 kPaPublished 181.8 kPa+0.39 % | Pass | |
| |||||||
Terzaghi, φ 30°, B 1.5 m BC-BOW-4-1 | 1641.21kPa | 1638.8kPa | +0.15 % | ± 1 % | Ours 1641.21 kPaPublished 1638.8 kPa+0.15 % | Pass | |
| |||||||
Hansen, submerged tank footing BC-BOW-4-2-H | 1817.75kPa | 1812kPa | +0.32 % | ± 1 % | Ours 1817.75 kPaPublished 1812 kPa+0.32 % | Pass | |
| |||||||
Meyerhof (1963), submerged tank footing BC-BOW-4-2-M | 2672.7kPa | 2659kPa | +0.52 % | ± 1 % | Ours 2672.7 kPaPublished 2659 kPa+0.52 % | Pass | |
| |||||||
Hansen, two-way eccentric 1.8 m square BC-BOW-4-5 | 5050.17kPa | 5088kPa | −0.74 % | ± 1.5 % | Ours 5050.17 kPaPublished 5088 kPa−0.74 % | Pass | |
| |||||||
Meyerhof inclined load — total checked against the book-consistent value, NOT the printed 399.9 kPa (documented source error) BC-BOW-4-7-TOTAL | 388.002kPa | 388.723kPa | −0.19 % | ± 1 % | Ours 388.002 kPaPublished 388.723 kPa−0.19 % | Pass | |
| |||||||
Meyerhof inclined load — cohesion term c·Nc·dc·ic BC-BOW-4-7-C | 343.294kPa | 344kPa | −0.21 % | ± 0.5 % | Ours 343.294 kPaPublished 344 kPa−0.21 % | Pass | |
| |||||||
Square pad on soft clay, undrained, DA1-C1 BC-DG-6.1-UND-DA1C1 | 586.786kN | 586kN | +0.13 % | ± 1 % | Ours 586.786 kNPublished 586 kN+0.13 % | Pass | |
| |||||||
Square pad on soft clay, undrained, DA1-C2 (c_u,d = 30/1.4) BC-DG-6.1-UND-DA1C2 | 433.995kN | 433kN | +0.23 % | ± 1 % | Ours 433.995 kNPublished 433 kN+0.23 % | Pass | |
| |||||||
Square pad on soft clay, undrained, DA2 BC-DG-6.1-UND-DA2 | 580.114kN | 580kN | +0.02 % | ± 1 % | Ours 580.114 kNPublished 580 kN+0.02 % | Pass | |
| |||||||
Square pad on soft clay, undrained, DA3 BC-DG-6.1-UND-DA3 | 600.686kN | 600kN | +0.11 % | ± 1 % | Ours 600.686 kNPublished 600 kN+0.11 % | Pass | |
| |||||||
Square pad, drained, DA1-C1 BC-DG-6.1-DRN-DA1C1 | 661.588kN | 660kN | +0.24 % | ± 1 % | Ours 661.588 kNPublished 660 kN+0.24 % | Pass | |
| |||||||
Square pad, drained, DA1-C2 BC-DG-6.1-DRN-DA1C2 | 410.474kN | 410kN | +0.12 % | ± 1 % | Ours 410.474 kNPublished 410 kN+0.12 % | Pass | |
| |||||||
Square pad, drained, DA2 BC-DG-6.1-DRN-DA2 | 528.021kN | 529kN | −0.19 % | ± 1 % | Ours 528.021 kNPublished 529 kN−0.19 % | Pass | |
| |||||||
Square pad, drained, DA3 BC-DG-6.1-DRN-DA3 | 562.158kN | 562kN | +0.03 % | ± 1 % | Ours 562.158 kNPublished 562 kN+0.03 % | Pass | |
| |||||||
Tower base, eccentric + inclined, DA1-C2 BC-DG-6.2-DA1C2 | 4337.21kN | 4330kN | +0.17 % | ± 1 % | Ours 4337.21 kNPublished 4330 kN+0.17 % | Pass | |
| |||||||
Pier on sand, AASHTO CWγ = 0.786 BC-NHI-A7 | 36250.1psf | 36609psf | −0.98 % | ± 1 % | Ours 36250.1 psfPublished 36609 psf−0.98 % | Pass | |
| |||||||
IS 6403 Table 1 Nc at φ = 45° — checked against the corrected value, NOT the printed cell BC-IS-T1-NC45 | 133.874 | 133.88 | −4.6e-3 % | ± 0.1 % | Ours 133.874Published 133.88−4.6e-3 % | Pass | |
| |||||||
IS 6403 Table 1 Nγ at φ = 30° BC-IS-T1-NG30 | 22.4025 | 22.4 | +0.01 % | ± 0.1 % | Ours 22.4025Published 22.4+0.01 % | Pass | |
| |||||||
Prandtl strip, Tresca, smooth FE-PRANDTL-SMOOTH | 5.13612 | 5.14159 | −0.11 % | ± 0.5 % | Ours 5.13612Published 5.14159−0.11 % | Pass | |
| |||||||
Prandtl strip, Tresca, rough FE-PRANDTL-ROUGH | 5.1601 | 5.14159 | +0.36 % | ± 0.5 % | Ours 5.1601Published 5.14159+0.36 % | Pass | |
| |||||||
Davis & Booker (1973) strip, smooth, c = 1 + 2z kPa FE-DAVIS-BOOKER-SMOOTH | 7.81694kPa | 7.79982kPa | +0.22 % | ± 1 % | Ours 7.81694 kPaPublished 7.79982 kPa+0.22 % | Pass | |
| |||||||
Davis & Booker (1973) strip, rough FE-DAVIS-BOOKER-ROUGH | 9.15482kPa | 9.08956kPa | +0.72 % | ± 1 % | Ours 9.15482 kPaPublished 9.08956 kPa+0.72 % | Pass | |
| |||||||
Cox (1962) smooth rigid circle, axisymmetric FE-COX-CIRCULAR | 226.204kPa | 225.6kPa | +0.27 % | ± 1 % | Ours 226.204 kPaPublished 225.6 kPa+0.27 % | Pass | |
| |||||||
Reissner N_q, weightless c = 0 strip with surcharge FE-REISSNER-NQ | 183.403kPa | 184.011kPa | −0.33 % | ± 1 % | Ours 183.403 kPaPublished 184.011 kPa−0.33 % | Pass | |
| |||||||
N_γ strip on cohesionless sand, smooth (c = 0, q = 0) FE-NGAMMA-SMOOTH | 415.506kPa | 612.24kPa | −32.1 % | ± 1 % | Ours 415.506 kPaPublished 612.24 kPa−32.1 % | Miss | |
| |||||||
N_γ strip on cohesionless sand, rough (c = 0, q = 0) FE-NGAMMA-ROUGH | 1249.39kPa | 1180.34kPa | +5.85 % | ± 1 % | Ours 1249.39 kPaPublished 1180.34 kPa+5.85 % | Miss | |
| |||||||
N_γ strip on cohesionless sand, smooth — FE limit analysis: do the lower and upper bounds contain the exact value? FELA-NGAMMA-SMOOTH | 646.99kPa | 612.24kPa | — | ± 0.01 % | Ours 646.99 kPaPublished 612.24 kPa— | Pass | |
| |||||||
N_γ strip on cohesionless sand, rough — FE limit analysis: do the lower and upper bounds contain the exact value? FELA-NGAMMA-ROUGH | 1200.36kPa | 1180.34kPa | — | ± 0.01 % | Ours 1200.36 kPaPublished 1180.34 kPa— | Pass | |
| |||||||
GEO5 VM-02 spread footing, 7° terrain slope, DA2 (self-weight favourable) — GEO5's Brinch Hansen standard-analysis factor set BC-GEO5-VM02 | 381.919kPa | 381.706kPa | +0.06 % | ± 1 % | Ours 381.919 kPaPublished 381.706 kPa+0.06 % | Pass | |
| |||||||
GEO5 VM-02 spread footing, 7° terrain slope, DA2 (self-weight unfavourable) — GEO5's Brinch Hansen standard-analysis factor set BC-GEO5-VM02-C2 | 386.612kPa | 386.501kPa | +0.03 % | ± 1 % | Ours 386.612 kPaPublished 386.501 kPa+0.03 % | Pass | |
| |||||||
Cited validation suites
bearing-capacity-ec7-web-validationrecords a difference`bearing-capacity` — EN 1997-1:2004 Annex D anchored to a PUBLISHED European worked example.9 passing
Analyses validated: bearing-capacity
- PassJRC EC7 worked example A.3.3 — M1 material set (γφ′ = 1.00): Nq = 48.87, Nγ = 74.80
- PassJRC EC7 worked example A.3.3 — M2 material set (γφ′ = 1.25): Nq = 23.17, Nγ = 27.72
- PassE-37 regression: the OTHER Nγ forms are rejected by this anchor at both material sets
- PassE-37: the M2 Nγ error is LARGER than the M1 error — the discrepancy grows where it matters most
- PassEN 1997-1 Annex D shape factors: sq = 1+(B′/L′)sinφ′, sγ = 1−0.3(B′/L′), sc = (sq·Nq−1)/(Nq−1)
- PassAnnex D defines NO depth factors — embedment enters only through the surcharge q′
- PassE-37: pairing a Eurocode design approach with a non-Annex-D resistance model WARNS
- PassAnnex D inclination factors: exact for c′ = 0, and flagged as conservative when c′ > 0
- Passthe Annex D method is labelled and discoverable
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
bearing-capacity-is6403-web-validationrecords a differenceIS 6403:1981 — "Code of Practice for Determination of Bearing Capacity of Shallow Foundations" (First Revision) — validated against the tables printed in the standard.5 passing
Analyses validated: bearing-capacity
- PassIS 6403:1981 Table 1 — all 33 published bearing-capacity factors (Nc, Nq, Nγ)
- PassIS 6403:1981 Table 1 is internally consistent — Nc = (Nq−1)·cot φ and Nγ = 2(Nq+1)·tan φ
- PassIS 6403:1981 Table 2 — all 12 published shape factors
- PassIS 6403:1981 Table 1 Note — local shear uses φ′ = tan⁻¹(0.67·tan φ) and c′ = ⅔c
- PassIS 6403:1981 — the code default is IS_6403 with FoS = 3, and qnu/qns follow Cl 6
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
bearing-capacity-reliability-web-validationPUBLISHED-VALUES: 0 -- distinct published values for this engine (engine-level total, declared once); independent audit A2: each demand is bisected so the reliability equals the tabulated value, so the suite tests the inverse-normal functi…4 passing
Analyses validated: bearing-capacity-reliability
- PassBaecher and Christian (2003) Table 13.1 — reliability index against probability of failure (Normal column)
- PassBaecher and Christian (2003) Table 13.1 — the tails: 100 % and 0 % of 20 000 draws passing
- PassLook (2007) Tables 10.1, 10.2 and 10.5 — published COV of the friction angle applied by the sampler
- Passthe default COV lies inside the published 5-15 % range, and a COV outside [0, 2] is refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
bearing-capacity-web-validationWEB-BENCHMARK validation for the shallow-foundation bearing-capacity engine (the release rules mandatory ≥20 cited-value gate).5 passing
Analyses validated: bearing-capacity
- PassBC web 1–9: Nq at φ=5..45 (Prandtl/Vesic 1973, Das Table 4.3)
- PassBC web 10–14: Nc at φ=0,10,20,30,40 (Prandtl/Vesic 1973)
- PassBC web 15–19: Vesic Nγ at φ=20,25,30,35,40 (Vesic 1973)
- PassBC web 20–22: Hansen Nγ at φ=20,30,40 (Hansen 1970)
- PassBC web 23–29: Terzaghi Nc & Nq at φ=0,20,30,35,40 (Terzaghi 1943, Das Table 3.1)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
bearing-capacity-worked-examples-web-validationrecords a differencebearing-capacity — FULL WORKED EXAMPLES (the ≥20-value gate, end-to-end q_ult / R_d rather than factor tables; the factor tables are `bearing-capacity-web-validation.test.ts`).32 passing
Analyses validated: bearing-capacity
- Pass[DAS] Ex 4.1 Terzaghi square, c′ 20, φ′ 25°, γ 16.5, Df 1.5, B 2 → q_u = 1078.29 kPa
- Pass[DAS] Ex 4.3 general equation, same footing → q_u = 1373.2 kPa
- Pass[DAS] Ex 4.4 water above the base (effective stress), B = 4.5 ft → q_u = 3·q_all = 1080 kPa
- Pass[DAS] Ex 4.5 inclined load β = 20°, square 1.25 m, φ′ 30°, Df 0.7 → q_u = 273.66 kPa
- Pass[DAS] Ex 4.7 eccentric strip e = 0.2 m → q′_u = 3287.39 kPa
- Pass[DAS] Ex 4.7 → Q_u = q′_u·B′ = 5260 kN/m
- Pass[DAS] Ex 4.12 eccentric + inclined strip → q′_u = 461.98 kPa
- Pass[DAS] case study — Bozozuk silo, φ = 0, c_u 23.3, 7.2 m square, Df 1.52 → q_u = 181.8 kPa
- Pass[DAS] case study — Bangkok clay, c_u 14.4, Df 1.5, B = 0.6 m → q_u(theory) = 158.3 kPa
- Pass[DAS] case study — Bangkok clay, c_u 14.4, Df 1.5, B = 0.675 m → q_u(theory) = 156.8 kPa
- Pass[DAS] case study — Bangkok clay, c_u 14.4, Df 1.5, B = 0.75 m → q_u(theory) = 155.4 kPa
- Pass[DAS] case study — Bangkok clay, c_u 14.4, Df 1.5, B = 0.9 m → q_u(theory) = 152.6 kPa
- Pass[DAS] case study — Bangkok clay, c_u 14.4, Df 1.5, B = 1.05 m → q_u(theory) = 150.16 kPa
- Pass[BOW] Ex 4-1 Terzaghi, φ 20°: q_ult = 613.8 + 34.6·B at B = 1.5 m
- Pass[BOW] Ex 4-1 Terzaghi, φ 30°, B = 1.5 m → q_ult = 1638.8 kPa
- Pass[BOW] Ex 4-2 Hansen (sq = 1 + B/L·sin φ = 1.18) → q_ult = 1812 kPa
- Pass[BOW] Ex 4-2 Meyerhof (Nγ = 414) → q_ult = 2659 kPa
- Pass[BOW] Ex 4-3 Hansen φ = 0: 5.14·s_u·(1 + s′c + d′c) = 15.6 t/m² (q neglected)
- Pass[BOW] Ex 4-5 Hansen, two-way eccentric 1.8 m square → q_ult = 5088 kPa
- Pass[BOW] Ex 4-7 Meyerhof inclined (θ = 18.4°): cohesion term c·Nc·dc·ic = 344.0 kPa
- Pass[DG] Ex 6.1 undrained DA1-C2 (c_u,d = 30/1.4): R/A′ = 150 kPa, R_d = 433 kN
- Pass[DG] Ex 6.1 undrained DA1-C1: R/A′ = 203 kPa, R_d = 586 kN
- Pass[DG] Ex 6.1 undrained DA2, B = 2.0 m → R_d = 580 kN
- Pass[DG] Ex 6.1 undrained DA3, B = 2.0 m → R_d = 600 kN
- Pass[DG] Ex 6.1 drained DA1-C2, B 1.85 (γ′ = 8, q′ = 8) → R/A′ = 120 kPa, R_d = 410 kN
- Pass[DG] Ex 6.1 drained DA1-C1, B 1.85 → R/A′ = 193 kPa, R_d = 660 kN
- Pass[DG] Ex 6.1 drained DA2, B 1.95 → R_d = 529 kN
- Pass[DG] Ex 6.1 drained DA3, B 2.15 → R/A′ = 121.5 kPa, R_d = 562 kN
- Pass[DG] Ex 6.2 tower DA1-C2: e = 2.19 m on B = 5.6 m, H/V = 0.182 → R/A′ = 637 kPa, R_d = 4330 kN (on A′ = 6.83 m²)
- Pass[NHI] App. A.7 pier on sand, AASHTO CWγ = 0.786 → q_ult = 36 609 psf
- Pass[NHI] Ex 8-1 water table at the base halves the weight term: 2025 → 1014 psf
- Pass[GEC6] App. B Ex 1: B = 6 m, Df 2.3 m, water 9.1 m → CWγ ≈ 0.9 (1.5·B influence depth)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
combined-footing-web-validationrecords a differenceRectangular combined footing proportioned for uniform soil pressure (`combined-footing.ts`) vs PUBLISHED worked examples.7 passing
Analyses validated: combined-footing
- PassDas Example 8.1 — Q1 = 400 kN, Q2 = 500 kN, qnet = 140 kN/m², L3 = 3.5 m, L2 = 1.5 m
- PassDas Example 8.2 — Q1 = 1000 kN, Q2 = 400 kN, qnet = 120 kN/m², L3 = 3 m: area and resultant
- PassVarghese Example 2.2 — 180 kN and 360 kN columns 2.1 m apart, safe bearing capacity 100 kN/m²
- PassNPTEL Lesson 29 Problem 5 — C1 400 × 400 (800 kN) flush with the property line, C2 300 × 500 (1200 kN), 3.0 m apart, qc = 200 kN/m²
- PassBaban Problem 5.16(A) — working loads 550 + 700 kN, net qa = 150 kPa
- PassBaban Problem 5.16(A) — factored loads 800 + 960 kN give L = 2X = 6.8 m
- PassBaban Problem 5.13 — interior column with no room beyond it: a rectangular footing is not possible
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
compensated-foundation-web-validationrecords a differenceCompensated (floating) foundation — net pressure q_net = q_gross − γ·Df and degree of compensation (`compensated-foundation.ts`) vs PUBLISHED worked examples.9 passing
Analyses validated: compensated-foundation
- PassVarghese Example 18.1 — ten-storey raft, 150 kN/m² gross, excavated 4.5 m in clay of 20 kN/m³
- PassVarghese Example 18.2 — the same building as a floating foundation: d = 150/20 = 7.5 m
- PassDas Example 8.6 — 30 × 40 m mat, Q = 200 × 10³ kN, Df = 2 m, γ = 15.72 kN/m³
- PassBaban Problem 2.1(c) — 40 × 80 m mat, 10 m deep, water table at 5 m
- PassBaban Problem 4.1 — silo on a 22.5 × 60 m mat, 3 m deep, clay of 17.5 kN/m³ with the water table at ground level
- PassBaban Problem 4.3 — square footing 4.5 m deep in saturated clay, water table at the surface
- PassFHWA-NHI-06-089 Example 8-2 — Δp = 2,000 psf − 3 ft × 115 pcf
- PassFHWA-NHI-06-089 Appendix A.7 — Δp = 6,000 psf − 4 ft × 110 pcf
- PassFHWA-NHI-06-089 Appendix A.7 embankment footing — Δp = 6,300 psf − 10 ft × 130 pcf
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
eccentric-footing-pressure-web-validationrecords a differenceContact pressure under an eccentrically loaded footing (`eccentric-footing-pressure.ts`) vs PUBLISHED worked examples.12 passing
Analyses validated: eccentric-footing-pressure
- PassVarghese Example 2.1 — 2.6 × 2.6 m footing, 600 kN with 100 kN·m
- PassVarghese Example 7.1 — effective dimensions of the 2 × 2 m footing (600 kN, Mx = 180, My = 60)
- PassVarghese Example 7.3 — retaining-wall base, 433 kN/m on 3.9 m, load 1.75 m from the toe
- PassVarghese Example 7.4 — 3.3 × 3.3 m footing, 300 kN with 150 kN·m
- PassVarghese Example 7.5 — the same footing, conventional pressures 27.5 ± 25 kN/m²
- PassVarghese Example 7.6 — layout for uniform pressure: B′ = 2.3 m and 131 kN/m²
- PassBaban Problem 2.2 — strip footing 1.5 m wide, V + Wf = 218 kN/m, My = 40 kN·m/m
- PassBaban Problem 2.3 — mat 50 × 75 m under six grain silos, three one-way cases
- PassBaban Chapter 6 (EC7) strip footing 6.5 × 2 m — combination 1: resultant inside the middle third
- PassBaban Chapter 6 (EC7) strip footing — combination 2: resultant OUTSIDE the middle third
- PassBaban Chapter 6 (EC7) strip footing — combination 3
- PassDas Example 4.7 (effective width) and the §4.10 beyond-kern relation
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
equivalent-raft-web-validationrecords a differenceEquivalent-raft pile-group settlement (`equivalent-raft.ts`) vs PUBLISHED values.8 passing
Analyses validated: equivalent-raft
- PassDas Example 9.23 — Qg = 2000 kN, Lg = 3.3 m, Bg = 2.2 m, 15 m piles
- PassVarghese Example 4.7 — nine 200 mm friction piles, 400 kN, 6 m of pile in clay
- PassTomlinson Example 5.1 — friction piles, 13.90 m, equivalent raft 10.5 × 13.8 m
- PassTomlinson Example 5.2 — piles 7 m into sand below the seabed, raft 10.4 × 9.1 m
- PassTomlinson Example 5.3 — 20 × 15 piles of 900 kN, raft 35.4 × 27.4 m
- PassTomlinson Example 5.4 — 12-storey building, raft 52.25 × 22.25 m: pressure and oedometer products
- PassFHWA GEC 6 Table B2-3 — 2-on-1 stress increase Δσv/q for Lf = 25.0 m
- PassIRC:78-2014 Cl. 709.3.4 — raft position for friction and end-bearing piles (clause-rule check, not a worked answer)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-bearing-capacity-hs-web-validationWEB-BENCHMARK validation for the HARDENING-SOIL stress-dependent stiffness option of the FE bearing-capacity engine.9 passing
Analyses validated: fe-bearing-capacity, hardening-soil
- PassFE-HS REDUCTION: m=0 ≡ constant-E MC engine (q_ult + settlement identical)
- PassFE-HS REDUCTION: φ=0 undrained ⇒ HS stiffness inert (identical to MC)
- PassFE-HS STRENGTH: q_ult is stiffness-independent (HS on ≈ off within 5%)
- PassFE-HS POWER-LAW: uniform confining E matches the HS SoilTest power law
- PassFE-HS MONOTONIC: E grows with depth; spread widens with m
- PassFE-HS WEB: loose Hostun sand E(σ₃) matches published HS power law (4 cases)
- PassFE-HS WEB: dense Hokksund sand E(σ₃) matches published HS values (4 cases)
- PassFE-HS WEB: Vesić Nc/Nq/Nγ match the published closed form (φ = 0,20,25,30,35°)
- PassFE-HS SETTLEMENT: HS stiffness changes the service settlement (finite, sane)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-bearing-capacity-web-validationfe-bearing-capacity — validation against PUBLISHED values, every number traced to a source.16 passing
Analyses validated: fe-bearing-capacity
- Pass[PZ2] Table 6.1: Nq(φ′=25°) with ψ=0 — published FE 9.92 (rough) / 10.0 (smooth)
- Pass[PZ2] §6.5.4.4: the ultimate Nq is independent of the surcharge magnitude
- Pass[SGM]/[MAR]: the combined c-φ-γ case lands within 15% of the EXACT characteristics solution
- PassE-77: the classical SUPERPOSITION is not a reliable yardstick — measured, both signs cited
- Pass[PR] Prandtl: Nc → 5.142 monotonically with refinement
- Pass[PR] Reissner: Nq is reproduced by the engine’s own closed form across φ′
- Passthe ψ=0 reduction deepens with φ′ and matches [PZ2] at the one φ′ they publish
- Pass[PZ2] Table 6.2: Nγ is UNDER-predicted — pinned as a known gap, not a passing check
- PassE-80 / D181: the self-weight part is DISCLOSED on every run that has one, with its measured share
- PassE-79 REGRESSION: the pure-Nγ configuration is not falsely refused
- PassD181: the pure-Nγ surface case is flagged NOT mesh-converged, with the measured cause
- PassE-80: with confinement the capacity is surcharge-dominated and tracks the exact Nq
- PassD175 [BOW]: at zero NET footing pressure the settlement is 0 — q = q_s with a surcharge, q → 0 without
- PassD175: the page-default settlement is the footing-induced part only — value and derivation
- PassD175: the K0 procedure has no geostatic phase to run, and a failed geostatic phase refuses LOUDLY
- PassD175 user-visible text: plain English, no em dash, no internal issue code, no competitor product name
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-footing-bvp-web-validationValidation for the 2-D plane-strain FOOTING bearing-capacity FE BVP with the Mohr-Coulomb + Hardening-Soil-stiffness material (`fe-footing-bvp.ts`) — the advanced-constitutive continuum solve that closes the "HS in a 2-D FE" gap.8 passing
Analyses validated: footing-bearing-fe
- PassVesić (1973) bearing-capacity factors N_c, N_q, N_γ — published table (13 anchors)
- PassPrandtl (1921): φ=0 strip footing q_ult = 5.14·s_u (FE within the coarse-mesh band)
- PassPrandtl: q_ult scales LINEARLY with s_u (correct undrained mechanics)
- PassSmith & Griffiths: FE bearing capacity converges toward the Prandtl limit as the mesh refines
- PassVesić (1973): frictional footing q_ult follows c·N_c + q₀·N_q (φ = 30°)
- Passload–settlement curve is monotone rising to the plateau
- PassHS stress-dependent stiffness: footing stiffness scales with E_ref (Schanz-Vermeer-Bonnier)
- Passsolver returns finite results and the represented footing width
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-hs-footing-web-validationValidation for the Hardening-Soil footing BVP (`fe-hs-footing-bvp.ts`) — the SVB shear-hardening return-map run at every Gauss point with per-point plastic state γ^p carried across displacement-controlled load increments (Phase 2 of HS-in-…6 passing
Analyses validated: footing-bearing-fe
- Passconstitutive-in-FE: a full-width footing (1-D confined compression) reproduces the material point
- PassPrandtl (1921): φ=0 HS footing q_ult = 5.14·s_u (coarse-mesh band, from above)
- PassPrandtl: q_ult scales linearly with s_u (correct undrained mechanics)
- PassSmith & Griffiths: FE bearing capacity converges to the Prandtl limit from ABOVE as the mesh refines
- Passfrictional (φ=30) HS footing collapse load is in the Vesić range and tracks the M-C solver
- Passload–settlement rises monotonically to the collapse peak (hardening), then q_ult is the peak
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
flotation-web-validationValidation for `flotation` — buoyancy / uplift (EN 1997-1 UPL) check of a buried structure (`flotation-check.ts`, `computeFlotation`).11 passing
Analyses validated: flotation
- PassCraig Ex 10.2: printed loads are 18 024 kN concrete + 15 200 kN soil on the roof
- PassCraig Ex 10.2: pore pressure on the base u = 117.7 − 9.8z kPa and uplift U = 47.1 − 3.9z MN
- PassCraig Ex 10.2 (a): empty store needs the water table at least 4.4 m down
- PassCraig Ex 10.2 (b): half-filled with books (+5.7 MN) ⇒ z ≥ 3.1 m
- PassCraig Ex 10.2: water table at the surface needs tension piles T ≥ 19.1 MN
- PassDesigners’ Guide Ex 7.5: V_dst,d = 1000 kN and G_stb,d = 450 kN per 5 m² of raft
- PassDesigners’ Guide §10.2.3 Eq. D10.7: the UPL check is an overall factor of safety 1.00/0.90 = 1.11
- PassWorked Examples A.6.1 step 1: weight of structure only — printed "requirement is not fulfilled"
- PassWorked Examples A.6.1 step 2: adding wall friction R_k = 2680 kN — printed "still not satisfied"
- PassEN 1997-1 Table A.15 and Craig Table 10.3: γG;dst = 1.00 and γG;stb = 0.90
- PassA dry base (water table below the base) has no uplift and passes every check
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
footing-bearing-fe-web-validationC.FOOTFE — `footing-bearing-fe` web-benchmark (25 cited published values).6 passing
Analyses validated: footing-bearing-fe
- PassC.FOOTFE.1: φ=0 strip footing converges on the exact Prandtl (2+π)·c_u from above
- PassC.FOOTFE.2: the φ=0 limit load is exactly proportional to c_u (scale invariance)
- PassC.FOOTFE.3: 18 published Vesić factors (strip — no shape factors) within 0.5%
- PassC.FOOTFE.4: undrained clay through the public entry point agrees with the closed form
- PassC.FOOTFE.5: clean sand (c′=0) reports no FE capacity instead of a wrong one
- PassC.FOOTFE.6: closed form is monotonic in strength and never returns non-finite
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
footing-near-slope-web-validationFooting on or near a slope crest (`footing-near-slope.ts`: Vesić Nc/Nq/Nγ, Hansen ground factors g_c, g_q, g_γ, linear set-back recovery to b = 2B) vs PUBLISHED values.4 passing
Analyses validated: footing-near-slope
- PassBowles Example 4-11 Case II — Hansen ground factor on a 1-on-2 slope (β = 26.5°, φ = 36°, γ = 14.85 kN/m³)
- PassFHWA-SA-02-054 §5.2.3.4 — capacity is independent of the slope beyond two to six footing widths
- PassDas Table 4.2 — Nc, Nq, Nγ (φ = 0, 10, 20, 30, 40, 50°)
- PassIS 6403:1981 Table 1 — Nc, Nq, Nγ (φ = 15, 25, 35°) and the 45° row
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
foundation-analysis-web-validationrecords a differenceFoundation-analysis orchestrator (`foundation-analysis.ts`) vs PUBLISHED values.15 passing
Analyses validated: foundation-analysis, settlement
- PassDas Example 7.7 — Meyerhof–Bowles pressure that gives the printed 14.7 mm
- PassBowles §4-10 example under Fig. 4-7 — qa with the depth factor
- PassBowles Example 5-9 — qa table for N55 = 25, D = 1.5 m
- PassVarghese Example 4.3 — Teng Eq. 4.4: 6.1 mm under 40 kN/m² (N = 20, B = 5 m)
- PassVarghese Example 4.4 — 13.7 mm under 100 kN/m² (N = 23, B = 10 m)
- PassVarghese Example 6.4 — q25 = 125 kN/m² (N = 15, B = 3 m)
- PassVarghese Example 6.5 — q25 = 274 and q40 = 438 kN/m² (N = 27, B = 2 m); allowable 440
- PassVarghese Example 8.5 — raft on sand, q25 = 64.7 kN/m² (N = 10, B = 9 m)
- PassDas Example 3.1 — (N1)60 by Liao–Whitman C_N (γ = 17.3 kN/m³, dry)
- PassDas Table 3.7 — C_N by the seven published relations at σ′/pa = 0.5 (1.5 for Eq. 3.16) and 2.0
- PassIS 6403 Table 1 — Nγ recovered through the orchestrator
- PassIS 6403 Table 1 — Nq recovered through the orchestrator
- PassIS 6403 Table 1 — Nc recovered through the orchestrator
- PassIS 6403 Table 2 — shape factors recovered as ratios to the strip footing
- Passhand-derived: ground water at the base halves the weight term (IS 6403 Cl 5.1.2.4, W′ = 0.5)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
foundation-practice-web-validationWeb-benchmark validation for TWELVE foundation/monitoring/groundwater runner engines.12 passing
Analyses validated: asaoka, combined-footing, compensated-foundation, cpt-sbt-ic, deadman-anchor, embankment-benching, equivalent-raft, footing-near-slope, pile-buckling, preconsolidation, pump-test, tunnel-settlement-trough
- Passpreconsolidation reproduces the Casagrande break and the recompression index
- Passasaoka recovers β₀, β₁ and the asymptote from the 1978 recurrence
- Passcpt-sbt-ic reproduces Robertson (2009) I_c including the stress-exponent iteration
- Passpile-buckling uses the Davisson-Robinson depth to fixity with Euler
- Passtunnel-settlement-trough reproduces the Peck (1969) Gaussian
- Passcompensated-foundation computes net pressure and the degree of compensation
- Passpump-test reproduces Cooper & Jacob (1946)
- Passequivalent-raft applies the Tomlinson raft depth and 2:1 spread
- Passfooting-near-slope uses Vesić N-factors with Hansen/Vesić ground factors
- Passcombined-footing places the base so the pressure is uniform (Bowles §9)
- Passdeadman-anchor computes the Teng (1962) net passive resistance
- Passembankment-benching sizes IRC:75 benches from the existing slope
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hardening-soil-footing-web-validation≥20-ANCHOR WEB/LITERATURE BENCHMARK for the Hardening-Soil footing BVP (`fe-hs-footing-bvp.ts`) — the LAST GATE before this engine may be surfaced live.14 passing
Analyses validated: footing-bearing-fe, hardening-soil-footing
- Pass[1-4] Prandtl (1921)/Reissner (1924): φ=0 q_ult = 5.14·s_u at four strengths (from above)
- Pass[5] Prandtl: q_ult/s_u is a CONSTANT (correct undrained mechanics, no strength scaling error)
- Pass[6-8] Smith & Griffiths: the FE collapse load converges to the Prandtl limit FROM ABOVE
- Pass[9-12] Vesić (1973)/Terzaghi (1943): frictional q_ult tracks c·N_c + q₀·N_q at φ = 20/25/30/35°
- Pass[13] capacity increases monotonically with friction angle (correct frictional mechanics)
- Pass[14] Davis (1968): associated (ψ=φ) and non-associated (ψ=0) collapse loads, and HS-vs-MC agreement
- Pass[15-17] SVB (1999) constitutive-in-FE: the 1-D confined patch test reproduces the material point
- Pass[18-19] Elasticity (Boussinesq / Poulos & Davis 1974): the low-load branch is linear in load
- Pass[20] settlement scales inversely with stiffness (doubling E halves the early settlement)
- Pass[21] capacity increases with cohesion (the c·N_c term)
- Pass[25-28] Terzaghi/Vesić: the q₀·N_q SURCHARGE term is mobilised — q_ult tracks c·N_c + q₀·N_q over a 20× q₀ range
- Pass[22] the load-settlement curve hardens monotonically to the collapse peak, and q_ult IS that peak
- Pass[23] plastic shear γ^p is mobilised under every frictional footing (the HS hardening state works)
- Pass[24] all runs mobilise a collapse plateau and return finite, physical numbers
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
limit-analysis-bearing-web-validationWEB-BENCHMARK validation for the FE limit-analysis bearing-capacity bracket.11 passing
Analyses validated: limit-analysis-bearing
- PassLA web A1–A8: bracket contains exact Prandtl 5.14·cu across cu (25,50,100,10,200,75,150,90)
- PassLA web A1: Nc_lower ≤ 5.14159 ≤ Nc_upper
- PassLA web A9–A11: surcharge adds directly (Nq=1) — bracket contains 5.14·cu + q_s
- PassLA web A12: c=0 ⇒ q_ult ≈ surcharge (best estimate = q_s)
- PassLA web A13–A14: q_ult ∝ cu (linear in cohesion)
- PassLA web A15–A16: q_ult independent of footing width B (weightless φ=0)
- PassLA web A18/A24: best estimate (mean of bounds) is within the guaranteed error of exact
- PassLA web A19: bracket width % is finite and the bounds are ordered
- PassLA web A23: refined mesh keeps a valid bracket containing Prandtl
- PassLA web: bound convergence closes toward exact 2+π as the mesh refines
- PassLA web: lower-bound stress field emitted (compression under the footing)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
plate-load-is1888-web-validationplate-load — the IS 1888 / Terzaghi-Peck / Housel paths against PUBLISHED values (deep review D10, 2026-10-01).15 passing
Analyses validated: plate-load
- Pass[CB] Cl 5.3 forward scaling: 12 mm on a 750 mm plate → 17.78 mm under a 2 m footing
- Pass[SV] Cl 5.3 inverse: a 25 mm footing (1.5 m) corresponds to 16 mm on a 600 mm plate; ≈ 290 kPa there
- Pass[DS] clay: S_f = S_p·B/B_p (Das §7.12) and the footing ultimate equals the plate's (Eq. 7.73)
- Pass[ER][SV] sand: footing ultimate = plate ultimate × B/B_p (Das Eq. 7.74, Bowles Eq. 4-21)
- Pass[NIRM] PLT-1: IS 1888 Cl 5.2 log-log yield ≈ 60.17 T/m² (Table 4.7)
- Pass[NIRM] PLT-2: IS 1888 Cl 5.2 log-log yield ≈ 75.02 T/m² (Table 4.7)
- Pass[NIRM] PLT-3: IS 1888 Cl 5.2 log-log yield ≈ 70.33 T/m² (Table 4.7)
- Pass[NIRM] PLT-4: IS 1888 Cl 5.2 log-log yield ≈ 65.02 T/m² (Table 4.7)
- Pass[SV][CB] arithmetic-tangent readings (335, 500 kPa) — the IS 1888 log-log value is lower, within 12 %
- Passa test that never yielded reports a LOWER BOUND and says so
- Pass[BW] Bowles §4-12.2 Housel: q₁ 50.83 kPa, q₂ 11.17 kN/m, 3 × 3 m base 591.5 kN
- Pass[ER] Housel, circular plates: s = 46.13 kN/m, q = 93.48 kN/m², 1.2 m footing Q = 279.6 kN
- PassHousel refuses one plate, or two plates of the same perimeter/area ratio
- Passnegative or non-finite readings are refused; a repeated pressure keeps its largest settlement
- Passthe settlement-controlled pressure discloses a clamp when the test stopped short of it
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
plate-load-web-validation`plate-load` — the ASTM D1195 / D1196 (US, and via DIN 18134 European) path.16 passing
Analyses validated: plate-load
- PassASTM D1195 App. X1: the normal equations recover a0, a1, a2 of a known parabola exactly
- PassASTM D1195 §12.2.4: the FIRST stage of the first cycle is excluded from its fit
- PassASTM D1195 §12.2.5: the first stage of the SECOND cycle IS included in its fit
- PassASTM D1195 §12.2.8 Eq. (3): Ev = 1.5·r·1/(a1 + a2·σ0max), evaluated by hand
- PassASTM D1195 App. X1.2: Eq. (3) equals the 0.3-0.7·σ0max SECANT on the fitted parabola
- PassASTM D1195 §12.2.9: Ev2 uses the SECOND cycle curve but the FIRST cycle σ0max
- PassASTM D1195 Tables 1 and 2: the published load stages are accepted as given
- PassASTM D1195 §11.2.2: fewer than six first-cycle stages is warned, not silently accepted
- PassASTM D1195 §11.2.5 / §11.2.6: the per-plate stress and settlement limits are checked
- PassASTM D1196 §12.3 Eq. (2) and IS 9214 Cl 2.3 are the SAME formula — one implementation serves both
- PassE-42: K is disclosed as a LOWER BOUND when the test never reached 1.25 mm
- PassASTM D1196 §12.3 NOTE 2: a plate other than 762 mm is flagged for road/airfield K
- Passa fit that cannot be determined is refused rather than reported as zero
- Passno first-cycle data is an ERROR — σ0max is undefined without it
- Passa reload softer than the first cycle is flagged as physically suspect
- Passevery numeric output is finite, and the governing clauses are cited
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
punching-shear-web-validationrecords a differenceTwo-way (punching) shear of a footing or pile cap, IS 456:2000 Cl 31.6.3 (`punching-shear.ts`) vs PUBLISHED worked examples.12 passing
Analyses validated: punching-shear
- PassNPTEL Problem 2 — 400 × 400 column, 2.6 × 2.6 m footing, d = 536 mm, M20, factored pressure 0.333 N/mm²
- PassNPTEL Problem 3 — 400 × 400 column, 3.4 × 3.4 m footing, d = 596 mm, M20, factored pressure 0.18166 N/mm²
- PassNPTEL Problem 4 — 300 × 450 column, 2.7 × 2.85 m footing, d = 600 mm, M25, average pressure 242.105 kN/m²
- PassNPTEL Problem 5 — combined footing, interior column C2 300 × 500, d = 666 mm, M20, pressure 250 kN/m²
- PassNPTEL Q.1/A.1 — 300 × 500 column, 5 × 3 m footing, d = 1091 mm, M20, factored pressure 300 kN/m²
- PassNPTEL TQ.1 — 450 × 300 column, 2.7 × 2.64 m footing, d = 547 mm, M25, uniform pressure 227.27 kN/m²
- PassMittal (2025) pile-cap example — four piles, 570 kN equivalent axial load each, d = 740 mm, M25
- PassBowles Example 8-2 — 0.35 m column, 2 × 2 m footing, Pu = 1.4(350) + 1.7(450) = 1255 kN: d = 0.32 m at vc = 1.30 MPa
- PassBowles Example 8-9 — 0.50 × 0.40 m column, Pcol = 2480 kN, d = 501.73 mm: vc = 1298.40 kPa
- PassBowles Example 8-10 — 0.50 × 0.50 m column, Pcol = 2480 kN, d = 484.86 mm: vc = 1298.40 kPa
- PassBowles Example 8-8 — 0.45 m square column, Pu = 3291.4 kN, d = 0.66 m
- PassIS 456 Cl 31.6.3.1 — ks = 0.5 + βc capped at 1, τc = 0.25√fck (clause-rule checks, not worked answers)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
raft-sizing-published-web-validationraft-sizing — deep review D12 (2026-10-02).11 passing
Analyses validated: raft-sizing
- Pass[Das Ex 8.5] 20 × 30 m mat, Q 110 MN, Df 1.5 m — gross 183.3, net 156.3 kPa, FS 5.36
- Pass[Das Ex 8.6] 30 × 40 m mat, Q 200 MN, γ 15.72, Df 2 m — net load per unit area 135.2 kPa
- Pass[Das Ex 8.7 / IS 2950 App D] 20.5 × 27.5 m mat with My 8 373 and Mx 1 616 kN·m — corner pressures
- Pass[SV] Fully compensated depth Df = (Q/A)/γ = 75/18 = 4.167 m
- Pass[SV] Partially compensated: at the published Df = 0.821 m the FS-3 net pressure is exactly used up
- Pass[MCL] Minimum square under P = 864 kN and M = 100 kN·m with q_allow 175 kPa — B = 2.51 m
- Pass[MCL] Adopted B = 2.6 m → q_max = 161.946 kPa
- Pass[CGT] Biaxial: P 400, 12 × 10, e_L 0.30, e_B 0.20 — kern 0.27, corners 4.233 / 3.433 / 3.233 / 2.433, U = 0.847
- Pass[IS 2950 App D NOTE / Das Eq. 4.49] one-way partial contact satisfies equilibrium
- Pass[IS 2950 Cl 4.3] a raft shallower than 1 m is flagged
- PassD12 — a raft with self-weight grows to the exact minimum where (P + γc·t·A)/A − γDf = SBC
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
raft-sizing-web-validationWeb-benchmark validation for `raft-sizing`.9 passing
Analyses validated: raft-sizing
- Passgross / net loading and utilisation follow the IS 2950 definitions
- Passoverburden relief is floored at zero and never makes net loading negative
- Passan overloaded raft grows until net loading meets SBC
- Passa site area cap is honoured and reported rather than silently exceeded
- Passq_max / q_min follow Bowles (P/A)(1 ± 6e_L/L ± 6e_B/B)
- Passthe kern limit is e = L/6 exactly, and beyond it uplift is reported
- Passbiaxial eccentricity superposes both kern terms
- Passinvalid inputs are refused with a zeroed geometry, not a plausible raft
- Passevery result carries its governing standard
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
raft-winkler-web-validationWeb-benchmark validation for `raft-winkler` — rigid, Winkler-FEM and Vesić-equivalent raft analysis.11 passing
Analyses validated: raft-winkler
- Passflexural rigidity is D = E·t³/[12(1 − ν²)] (Kirchhoff)
- Passa missing ks is correlated as q_safe/s_allow (Bowles 5e Eq 9-6a)
- Passa concentrically loaded rigid raft settles uniformly at s = q/ks (Winkler)
- Passa central point load on a rigid raft gives the same uniform pressure as its UDL
- Passan eccentric load produces the linear pressure distribution and can cause uplift
- Passrigid strip actions follow ACI 336.2R §3.3.2
- Passthe Winkler FEM reproduces w = q/ks for a uniformly loaded raft
- Passa stiffer plate spreads a point load further — the physical signature of the FEM
- Passthe Vesić biot_plate branch derives ks from Es and differs from the supplied-ks run
- Passa load outside the footprint is excluded and said so, not silently absorbed
- Passinvalid geometry and serviceability limits are both handled
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rigid-base-pressure-web-validationRigid rectangular base on a tensionless subgrade — biaxial partial contact (2026-10-03).11 passing
Analyses validated: not attributed by the manifest
- Pass[FULL] inside the kern it is the linear formula (civilgeotools worked example, ksf)
- Pass[DAS] one-way partial contact L 10, B 6, e 2.5: q_max 4P/3B(L−2e), contact 3(L/2−e)
- Pass[DAS] one-way partial contact L 8, B 8, e 2: q_max 4P/3B(L−2e), contact 3(L/2−e)
- Pass[DAS] one-way partial contact L 20, B 12, e 4: q_max 4P/3B(L−2e), contact 3(L/2−e)
- Pass[BB-A] corner triangle e_x/L 0.3, e_y/B 0.3: q_max = (P/BL)·3/(8(½−e_x/L)(½−e_y/B))
- Pass[BB-A] corner triangle e_x/L 0.35, e_y/B 0.25: q_max = (P/BL)·3/(8(½−e_x/L)(½−e_y/B))
- Pass[BB-A] corner triangle e_x/L 0.4, e_y/B 0.4: q_max = (P/BL)·3/(8(½−e_x/L)(½−e_y/B))
- Pass[BB-D] trapezoid e_x/L 0.02, e_y/B 0.3 (y-dominant) and its mirror
- Pass[BB-D] trapezoid e_x/L 0.05, e_y/B 0.33 (y-dominant) and its mirror
- Passpentagon zone (one corner lifted) satisfies equilibrium and is continuous with the kern
- Passrefusals: resultant outside the base, non-positive load
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
seismic-bearing-capacity-ec8-web-validationEN 1998-5:2004 ANNEX F seismic bearing capacity — web-validation benchmark.17 passing
Analyses validated: not attributed by the manifest
- PassTable F.1 — all 14 numerical parameters, both soil types
- PassTable F.2 — model partial factor γ_Rd, cross-checked against Pecker Table 4.8.1
- PassF.3 and F.6 — N_max closed forms
- PassF.4 and F.7 — the dimensionless soil inertia force F̄
- PassPecker §4.8.1.3 — 6 published intermediates and the published LHS = −0.999
- PassPecker §4.8.1.3 — (F.1) reproduces −0.999 from the text’s OWN rounded values
- Passthe F̄ strength-basis ambiguity is exactly γ_M, and immaterial in this example
- Passthe utilisation is U-SHAPED in N̄ — a footing can fail for too LITTLE axial load
- Passthe F.5 / F.8 constraints are refusals, not warnings
- Passthe two F.5 permissions are opt-in, and the cohesionless one is CONDITIONAL
- Passthe Table F.2 row must match the soil idealisation
- PassAnnex F declares itself INFORMATIVE and reports a utilisation, not a safety factor
- PassAnnex E — (E.3) is exactly (E.2) with the bracket dropped, so a clamped radical reproduces it
- PassAnnex E — the branch switch is continuous at β = φ′_d − θ
- PassAnnex E — K rises with kh, with backfill slope, and the passive branch differs from the active
- PassAnnex E — (E.1) total design force, and (E.17) hydrodynamic force
- PassAnnex E — design angles φ′_d and δ_d divide the TANGENT, not the angle
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
subgrade-reaction-web-validationrecords a differencePUBLISHED-VALUES: 14 -- distinct published values for this engine (engine-level total, declared once); independent audit A3: about 14 distinct published values (the Baban table is a copy of Bowles).5 passing
Analyses validated: subgrade-reaction
- PassBowles (1997) Eq. 9-9 — k_s = 40·SF·q_a in Bowles's own worked examples
- PassBowles (1997) Example 10-2 and the 25.4 mm / 12 mm / 20 mm factors of Eq. 9-9
- PassBaban (2016) Eq. 5.44 and Varghese (2005) Table 1.8 note — same rule, stated as a coefficient
- PassBowles (1997) Table 9-1 / Baban (2016) Table 5.3 — engine results fall in the published clayey-soil ranges
- PassBowles (1997) Example 9-5 / Baban (2016) Eq. 5.42 / Das (2016) Eq. 8.50 — Vesic reduced form Es/(B(1−μ²))
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
t6-limit-load-web-validationWEB-VALIDATION for the T6 element-accuracy / limit-load engine (`t6-limit-load.ts`).26 passing
Analyses validated: t6-limit-load
- PassA1 — no engine errors; a distorted patch mesh with Gauss points was built
- PassA2 — CONSTANT-strain patch: T6 reproduces εxx=g to ~machine zero on a distorted mesh
- PassA3 — LINEAR-stress (pure-bending) patch: T6 reproduces the linear σxx field exactly
- PassA4 — CST CANNOT reproduce the linear stress field (error is order-unity kPa)
- PassA5 — T6 beats CST on the linear field by ≥6 orders of magnitude (the LST advantage)
- PassA6 — patch test PASSES (both T6 errors within tolerance) — element is valid
- PassB1 — exact tip deflection uses κ = M(1−ν²)/(E·I), I = D³/12 (plane strain)
- PassB2 — T6 reproduces pure-bending tip deflection to <1e-3% error (essentially exact)
- PassB3 — T6 tip deflection matches the analytical δ (finest mesh)
- PassB4 — CST is far too stiff: its tip-deflection error is orders larger than T6
- PassB5 — T6 is exact at EVERY mesh level; CST error only decreases with refinement
- PassB6 — the coarsest CST mesh is grossly too stiff (>25% deflection error)
- PassB7 — T6 mesh has more nodes than the base CST mesh (mid-side enrichment)
- PassC1 — T6 element stiffness is symmetric (Kᵀ = K)
- PassC2 — exactly 3 plane rigid-body modes carry zero energy (2 translations + 1 rotation)
- PassC3 — rigid-body motion produces ~zero nodal forces
- PassC4 — the deformation stiffness is POSITIVE-DEFINITE (Cholesky pivots > 0)
- PassD1 — reported Prandtl reference is exactly Nc = 2 + π = 5.14159
- PassD2 — coarse displacement-FE bearing is finite, positive, and OVER-predicts Prandtl (locking overshoot)
- PassD3 — bearing carries the honest not-converged limitation note
- PassD4 — bearing is omitted by default (fast path) unless explicitly requested
- PassE1 — pure-bending deflection is LINEAR in applied moment M (δ ∝ M)
- PassE2 — deflection scales as L² (Euler-Bernoulli): δ(2L)/δ(L) = 4
- PassE3 — near-incompressible ν=0.49: load-driven T6 bending stays exact while CST over-stiffens (Nagtegaal-Parks-Rice locking)
- PassE4 — invalid inputs are guarded: E≤0 records an error, result shape stays well-formed
- PassE5 — narrative notes are present and name the T6/CST contrast
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
two-layer-bearing-web-validationTwo-layer bearing capacity, strong-over-weak punching mechanism (`two-layer-bearing.ts`, the Meyerhof-Hanna punching-block model) vs PUBLISHED values.7 passing
Analyses validated: two-layer-bearing
- PassDas Example 5.4 — sand over soft clay, continuous footing
- PassBaban Problem 4.23 — the same profile with the chart reading Ks = 3
- PassDas Example 5.5 — adhesion term of the clay-over-clay punching block
- PassDas Table 4.2 — top-layer Nc, Nq, Nγ
- PassDas Table 4.2 — further top-layer rows (5° and 25°)
- PassDas Table 4.2 — bottom-layer factors, including the φ = 0 clay
- PassIS 6403:1981 Table 1 — the SAME factors as Das Table 4.2 (one source, not two; it reprints the Nc(45°) misprint)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
well-foundation-web-validationPublished-value validation for the well (caisson) foundation elastic-theory check (`well-foundation.ts`, `computeWellFoundation`).12 passing
Analyses validated: well-foundation
- PassVarghese Example 20.3: base area A = π(8.5)²/4 = 56.72 m²
- PassVarghese Example 20.3: Iv = L D³/12 = 2151 m⁴ (L = 0.9 d = 7.65 m) and IB = π d⁴/64 = 256 m⁴
- PassVarghese Example 20.3: I = IB + m Iv (1 + 2μ′α) = 2,685.7 m⁴
- PassVarghese Example 20.3 Eq. 20.11: r = I D/(2 m Iv) = 9.36 m
- PassVarghese Example 20.3: P = M/r = 4,487 kN
- PassVarghese Example 20.3 Eq. 20.16: base pressures σ1 = 284 and σ2 = 152 kN/m²
- PassVarghese Example 20.3 Condition 3: m M/I = 15.6 kN/m³
- PassVarghese Example 20.3: all four conditions satisfied (base friction, direction, elastic state, base pressure)
- PassVarghese Example 20.1: at the limiting elastic state the side reaction is Pmax = γ(KP − KA) L D²/6 = 6,400 kN
- PassVarghese Example 20.1: vertical load at the base W − μ′P = 15,000 − 2,560 = 12,440 kN → mean base pressure 12,440/40 = 311 kN/m²
- PassVarghese Example 20.1: base pressures 809 kN/m² compression and 187 kN/m² tension at Hmax
- PassVarghese Example 20.1: at Hmax, m M/I equals the limiting value γ(KP − KA) = 10 × 8/3 = 26.67 kN/m³
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Settlement, stress distribution and consolidation
23 finite-element rows (1 superseded) · 0 closed-form problems · 39 validation suites
Finite-element solver registry
Showing 23 of 23 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
settlement at the centre of the tank plaxis-verif-flexible-tank | 74.207mm | 74.44mm | −0.31 % | Ours 74.207 mmPublished 74.44 mm−0.31 % | Pass | |
| ||||||
Terzaghi U(Tv): bottom excess p/p_ext at t = 2 d (Tv 0.2) k4-gate-terzaghi | 0.7642 | 0.764 | +0.03 % | Ours 0.7642Published 0.764+0.03 % | Pass | |
| ||||||
fully coupled (total pore pressure) 1-D consolidation vs Terzaghi k4-gate-terzaghi-fully-coupled | 0.7642 | 0.764 | +0.03 % | Ours 0.7642Published 0.764+0.03 % | Pass | |
| ||||||
Mandel–Cryer: centre p/q peak (rise above the undrained value) k4-gate-mandel-cryer | 0.53737 | 0.53804 | −0.13 % | Ours 0.53737Published 0.53804−0.13 % | Pass | |
| ||||||
Skempton B under isotropic undrained (A) loading k4-gate-skempton-b | 0.983278 | 0.983278 | 0.00 % | Ours 0.983278Published 0.9832780.00 % | Pass | |
| ||||||
oedometric undrained initial excess p0/p_ext k4-gate-oedometric-p0 | 0.980198 | 0.980198 | 0.00 % | Ours 0.980198Published 0.9801980.00 % | Pass | |
| ||||||
unsaturated column: hydrostatic vG state is an equilibrium of the fully coupled phase k4-gate-unsaturated-column | 0kPa | 0kPa | — | Ours 0 kPaPublished 0 kPa— | Pass | |
| ||||||
Undrained (B): max shear stress at failure = su k4-gate-undrained-b-su | 20kPa | 20kPa | 0.00 % | Ours 20 kPaPublished 20 kPa0.00 % | Pass | |
| ||||||
case 2 (Hypres coarse, unsaturated): volumetric strain plaxis-verif-undrained-coarse-ev | -0.0099562 | -0.009925 | +0.31 % | Ours -0.0099562Published -0.009925+0.31 % | Pass | |
| ||||||
case 2: effective vertical stress at the top point plaxis-verif-undrained-coarse-sv | -15.7481kPa | -15.744kPa | +0.03 % | Ours -15.7481 kPaPublished -15.744 kPa+0.03 % | Pass | |
| ||||||
case 3 (Hypres fine): volumetric strain plaxis-verif-undrained-fine-ev | -0.0098162 | -0.009787 | +0.30 % | Ours -0.0098162Published -0.009787+0.30 % | Pass | |
| ||||||
case 3: effective vertical stress plaxis-verif-undrained-fine-sv | -18.4154kPa | -18.413kPa | +0.01 % | Ours -18.4154 kPaPublished -18.413 kPa+0.01 % | Pass | |
| ||||||
Bishop σ′v at the column bottom (10 kPa uniform suction, χ = Se) plaxis-verif-bishop-sv-bottom | -43.2625kPa | -43.2625kPa | 0.00 % | Ours -43.2625 kPaPublished -43.2625 kPa0.00 % | Pass | |
| ||||||
borehole wall radial displacement (Biot α < 1) plaxis-verif-biot-borehole | -3.5022mm | -3.5022mm | 0.00 % | Ours -3.5022 mmPublished -3.5022 mm0.00 % | Pass | |
| ||||||
centre settlement, Undrained (C) (total stress Eu, νu) through the K4 drainage types plaxis-verif-flexible-tank-k4-undrained-c | 74.207mm | 74.44mm | −0.31 % | Ours 74.207 mmPublished 74.44 mm−0.31 % | Pass | |
| ||||||
consolidation-biot (TS oracle) column: settlement degree U at Tv 0.848 k4-crosscheck-consolidation-biot · Self-check | 0.89904 | 0.90003 | −0.11 % | Ours 0.89904Published 0.90003−0.11 % | Pass | |
| ||||||
Tutorial 9 (Soft Soil undrained A + HS, 4 consolidation phases): time to p_excess < 1 kPa, plus settlements / excess pore pressures per phase k5b-plaxis-2d-tut9-consolidation-time | t at p_excess < 1 kPa (d): 38.69; settlement (0,0) mm P1/P2/P3/P4: [261.4, 664.5, 829.5, 1033.7]; max p_excess kPa P1/P… | > 50 d | — | Ours t at p_excess < 1 kPa (d): 38.69; settle…Published > 50 d— | Superseded | |
| ||||||
Tutorial 9 with the change of permeability c_k (Table 9-1): time to p_excess < 1 kPa; settlements per phase; Safety phases 5–8 k5d-plaxis-2d-tut9-ck | t at p_excess < 1 kPa (d): 58.19; settlement (0,0) mm P1/P2/P3/P4: [199.9, 659.7, 746.1, 1031.5]; max p_excess kPa P1/P… | > 50 d; ≈ 1 m | — | Ours t at p_excess < 1 kPa (d): 58.19; settle…Published > 50 d; ≈ 1 m— | Pass | |
| ||||||
time at which the phase stops, U = 50/90/99 % (step capped at 0.005 d) vs Terzaghi t* v-rm-degree-of-consolidation-capped-step | [3.8692, 10.5293, 20.0545] | [3.864, 10.5194, 20.0399] | [0.13, 0.09, 0.07] % | Ours [3.8692, 10.5293, 20.0545] dayPublished [3.864, 10.5194, 20.0399] day[0.13, 0.09, 0.07] % | Pass | |
| ||||||
stop time for |P-stop| = 0.30 and 0.05 kPa (step capped 0.005 d) vs Terzaghi t* v-rm-min-excess-capped-step | [5.8993, 13.3144] | [5.8942, 13.3026] | [0.09, 0.09] % | Ours [5.8993, 13.3144] dayPublished [5.8942, 13.3026] day[0.09, 0.09] % | Pass | |
| ||||||
stop time with the DEFAULT step control: P-stop 0.30 / U 50 % / U 90 % v-rm-consolidation-stop-default-stepping | [5.9194, 3.8771, 10.5903] | [5.8942, 3.864, 10.5194] | [0.43, 0.34, 0.67] % | Ours [5.9194, 3.8771, 10.5903] dayPublished [5.8942, 3.864, 10.5194] day[0.43, 0.34, 0.67] % | Pass | |
| ||||||
base excess pressure at t = 2 d, top drained by a DRAIN line (head = level) v-rm-drain-at-level-terzaghi | 0.7642kPa | 0.764kPa | +0.03 % | Ours 0.7642 kPaPublished 0.764 kPa+0.03 % | Pass | |
| ||||||
drain with head 0.2 m (level 1 m) in a consolidation phase: worst |p − Terzaghi| v-rm-drain-head-ignored-in-consolidation | 0.00115kPa | 0kPa | — | Ours 0.00115 kPaPublished 0 kPa— | Pass | |
| ||||||
Cited validation suites
asaoka-web-validationValidation of the Asaoka observational settlement forecast (`asaoka.ts`) against the PUBLISHED method.7 passing
Analyses validated: asaoka
- PassAsaoka Eq. (23): a record generated by Eq. (24) returns ρf = β0/(1 − β1)
- PassAsaoka Eq. (21): the regression slope is β1 and the intercept is β0 = ρf(1 − β1)
- PassAsaoka Eq. (23) with the Kobe Port No. 3 posterior modes (β1 = 0.9791, β0 = 6.94 cm, Fig. 6): ρf = 332 cm
- PassHan Eq. 7.63 / CEDD C4: cv = −4·hdr²·ln β1/(π²·Δt) for β1 = 0.8, hdr = 3 m, Δt = 30 days
- PassCEDD C3/C4 inverted: a Terzaghi-exponent record β1 = exp(−π²·cv·Δt/(4·H²)) gives back the cv that made it
- PassAsaoka 1978 Eq. (26) is NOT what the engine uses: for upward drainage ln β1 = −π²cv·Δt/(4H²), not −2cv·Δt/H²
- PassAsaoka Eq. (24): degree of consolidation and remaining settlement at the last reading
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
burland-burbidge-web-validationPUBLISHED-VALUES: 16 -- distinct published values for this engine (engine-level total, declared once); independent audit A3: about 16 distinct published values.9 passing
Analyses validated: burland-burbidge
- PassCraig (2012) Example 8.9 — compressibility index Ic = 1.71/N^1.4 at N = 10, 9, 8
- PassCraig (2012) Example 8.9 — settlement coefficient and the three converged widths give 25 mm
- PassCraig (2012) Fig 8.31 read in Example 8.9 — depth of influence z_I against B
- PassCraig (2012) Eq 8.68 text — creep factor Ft after 30 years, static vs variable loading
- PassDas (2016) Example 7.6 — 1.75 m square, N60 = 10, q = 120 kPa, normally consolidated
- PassDas (2016) Table 7.7 — over-consolidated branches use 1/3 of the normally consolidated compressibility
- PassBaban (2016) Problem 3.7 — 7.5 × 8.5 m pier base on dense sand and gravel, N = 40
- PassViana da Fonseca (2012) Eq 8.3 — coefficient 1.71 and influence depth B^0.75
- PassCraig (2012) Eqs 8.64, 8.66, 8.67 — N correction, shape factor, thin-layer factor (equation form)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
circular-load-stress-web-validationrecords a differencecircular-load-stress — dedicated web-benchmark against PUBLISHED values.4 passing
Analyses validated: circular-load-stress
- PassDas (2016) Table 6.1, r/(B/2) = 0 column — Δσ/q against z/(B/2), fourteen published values
- PassVarghese (2005) Table 3.3 and Bowles (1997) §5-3 — the Newmark r/z ↔ σz/q pairs
- PassDas (2016) Example 6.6 — B = 2 m circular area, q = 150 kPa, at z = 1, 3.5 and 6 m
- PassHoltz & Kovacs (1981) Example 8.20 — 3.91 m diameter tank, 117 kPa, z = 2 m under the centre
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
collapse-potential-web-validationValidation for `collapse-potential` — single-oedometer collapse potential I_c = Δh/h0 = Δe/(1+e0), ASTM D5333 severity and Jennings & Knight foundation-risk bands (`collapse-potential.ts`, `computeCollapsePotential`).5 passing
Analyses validated: collapse-potential
- PassASTM D5333 Table 1: 0 none; 0.1–2.0 slight
- PassASTM D5333 Table 1: 2.1–6.0 moderate; 6.1–10.0 moderately severe; > 10.0 severe
- PassJennings & Knight (1975): 0–1 no problem; 1–5 moderate trouble; 5–10 trouble
- PassJennings & Knight (1975): 10–20 severe trouble; > 20 very severe trouble
- PassStructville (2020) worked example: Δe_c = 0.04, e0 = 0.64, H = 4 m ⇒ collapse settlement S2 = 0.0975 m
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
compression-index-web-validationValidation of the compression / recompression index estimator (`compression-index.ts`) against the published correlations and the published WORKED ANSWERS that use them.8 passing
Analyses validated: compression-index
- PassBowles Example 5-14: wL = 78 % ⇒ Terzaghi–Peck Cc = 0.009(78 − 10) = 0.612
- PassBowles Example 5-15: wL = 50 % ⇒ Terzaghi–Peck Cc = 0.36
- PassVarghese Example 4.7: LL = 40 % ⇒ Cc = 0.009 × 30 = 0.27
- PassVarghese Example 4.11: LL = 65.5 % ⇒ Cc = 0.009 × 55.5 = 0.50
- PassLambe & Whitman Ch. 22 / Bowles Table 2-5: undisturbed Cc = 0.009(LL − 10) and remoulded Cc = 0.007(LL − 10) at LL = 60
- PassIS 8009 (Part 1) Eq. (8) / FHWA Table 5-5: Hough Cc = 0.30(e0 − 0.27) at e0 = 1.0
- PassDas Eq. 2.56 / Bowles Table 2-5: Nagaraj & Murthy Cc = 0.2343(LL/100)·Gs and Cr = 0.000463·wL·Gs at wL = 60, Gs = 2.7
- PassIS 8009 (Part 1) Eq. (7): the IS correlation equals the Terzaghi–Peck one at LL = 35 % (0.225)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
consolidation-biot-web-validationWeb-benchmark validation for the COUPLED BIOT consolidation FE (`consolidation-biot.ts`).33 passing
Analyses validated: not attributed by the manifest
- PassEoed = E(1−ν)/[(1+ν)(1−2ν)] — constrained modulus
- Passcv = (k/γw)·Eoed
- Passfinal settlement s∞ = σ·H/Eoed
- PassU_settlement(Tv=0.05) reproduces terzaghiUavg
- PassU_settlement(Tv=0.1) reproduces terzaghiUavg
- PassU_settlement(Tv=0.2) reproduces terzaghiUavg
- PassU_settlement(Tv=0.3) reproduces terzaghiUavg
- PassU_settlement(Tv=0.5) reproduces terzaghiUavg
- PassU_settlement(Tv=0.848) reproduces terzaghiUavg
- PassU_pressure(Tv=0.2) reproduces terzaghiUavg
- PassU_pressure(Tv=0.5) reproduces terzaghiUavg
- PassU_pressure(Tv=0.848) reproduces terzaghiUavg
- Passstandard table: U(Tv=0.008) ≈ 0.1 (Das/Terzaghi)
- Passstandard table: U(Tv=0.031) ≈ 0.2 (Das/Terzaghi)
- Passstandard table: U(Tv=0.071) ≈ 0.3 (Das/Terzaghi)
- Passstandard table: U(Tv=0.126) ≈ 0.4 (Das/Terzaghi)
- Passstandard table: U(Tv=0.197) ≈ 0.5 (Das/Terzaghi)
- Passstandard table: U(Tv=0.287) ≈ 0.6 (Das/Terzaghi)
- Passstandard table: U(Tv=0.403) ≈ 0.7 (Das/Terzaghi)
- Passstandard table: U(Tv=0.567) ≈ 0.8 (Das/Terzaghi)
- Passstandard table: U(Tv=0.848) ≈ 0.9 (Das/Terzaghi)
- Passstandard table: U(Tv=1.129) ≈ 0.95 (Das/Terzaghi)
- Passisochrone u_e/u₀ at (Z≈0.333, Tv=0.2) reproduces Terzaghi
- Passisochrone u_e/u₀ at (Z≈0.500, Tv=0.2) reproduces Terzaghi
- Passisochrone u_e/u₀ at (Z≈1.000, Tv=0.2) reproduces Terzaghi
- Passisochrone u_e/u₀ at (Z≈0.500, Tv=0.5) reproduces Terzaghi
- Passisochrone u_e/u₀ at (Z≈1.000, Tv=0.5) reproduces Terzaghi
- Passisochrone u_e/u₀ at (Z≈1.000, Tv=0.848) reproduces Terzaghi
- Passdrained face u_e=0; peak at the impermeable base; monotone with depth
- Passdouble drainage: Hdr = H/2 and cv unchanged
- Passdouble drainage U_settlement(Tv=0.2) reproduces terzaghiUavg
- Passdouble drainage U_settlement(Tv=0.5) reproduces terzaghiUavg
- PassU_settlement ≈ U_pressure (the 1-D Terzaghi identity)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
consolidation-degree-web-validationrecords a differenceValidation for `consolidation-degree` — the Terzaghi U ↔ T_v relationship (`consolidation-degree.ts`).6 passing
Analyses validated: consolidation-degree
- PassFHWA Table 7-4: Tv required for U = 10…98 %
- PassFHWA Table 7-4: U reached at the tabulated Tv
- PassDas Table 2.11 entries (Tv printed to 3 s.f.)
- PassDas Example 2.12: U = 40/87.5 = 45.7 % needs Tv = 0.164; field time 45,523 min (31.6 days)
- PassFHWA Example 7-3: t90 = Tv·Hd²/cv = 0.848·10²/0.2 = 424 days
- PassCraig Example 4.7: Tv = 4.7·0.5/10² = 0.0235 ⇒ Uv = 0.17
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
consolidation-family-web-validationconsolidation-family-web-validation.test.ts8 passing
Analyses validated: consolidation-3d, coupled-consolidation, footing-bearing-3d
- PassTerzaghi U(T_v) reproduces the published table, both directions (10 anchors)
- PassTerzaghi U and T_v are exact inverses, and the small-U branch follows (π/4)U²
- Passcoupled-consolidation: E_oed, c_v and H_dr from the closed forms (6 anchors)
- Passcoupled-consolidation: final settlement is the confined 1-D value q·H/E_oed
- Passcoupled-consolidation: t₅₀ and t₉₀ match Terzaghi T_v·H_dr²/c_v, and U ends consistent (6 anchors)
- Passconsolidation-3d: the oedometer and Boussinesq comparisons it prints are the textbook values (7 anchors)
- Passconsolidation-3d: the Q2–Q1 pair reports more displacement DOF than pressure DOF
- Passfooting-bearing-3d: shape factors follow Vesić/Meyerhof, and Skempton for a square (11 anchors)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
consolidation-terzaghi-web-validationValidation for the Terzaghi consolidation series (`consolidation-terzaghi.ts`).14 passing
Analyses validated: not attributed by the manifest
- PassU_avg(Tv=0.002) ≈ 0.05 (standard table)
- PassU_avg(Tv=0.008) ≈ 0.1 (standard table)
- PassU_avg(Tv=0.031) ≈ 0.2 (standard table)
- PassU_avg(Tv=0.071) ≈ 0.3 (standard table)
- PassU_avg(Tv=0.126) ≈ 0.4 (standard table)
- PassU_avg(Tv=0.197) ≈ 0.5 (standard table)
- PassU_avg(Tv=0.286) ≈ 0.6 (standard table)
- PassU_avg(Tv=0.403) ≈ 0.7 (standard table)
- PassU_avg(Tv=0.567) ≈ 0.8 (standard table)
- PassU_avg(Tv=0.848) ≈ 0.9 (standard table)
- Passboundary values: U(0)=0, U(large)→1
- Passsmall-time approximation √(4Tv/π) matches the series for U<0.5
- Passpore-pressure isochrone: full u0 at t=0, drained face (Z=0) → 0
- PassCasagrande Tv(U) closed form matches the series-implied Tv
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
consolidation-time-rate-web-validationrecords a differenceWeb-benchmark validation for `consolidation-time-rate` — Terzaghi 1-D consolidation.8 passing
Analyses validated: consolidation-time-rate
- PassTv matches all nine published Uav–Tv pairs (TPM 1996 §16)
- PassU(Tv) inverts the published table at every point
- PassT50 and T90 meet the values the module advertises
- PassE-89: the hand approximation deviates from the table where measured
- PassE-89: Tv is smooth through U=60% (no branch step)
- Passdouble drainage quarters the time (Hdr = H/2)
- Passworked case: t90 = T90·Hdr²/Cv
- Passsettlement at the target degree is U × ultimate
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
coupled-consolidation-web-validationValidation of the COUPLED CONSOLIDATION analysis (Biot u–p finite-element column, `consolidation-biot.ts`: `biotColumn` and the runner wrapper `computeBiotColumnConfig`) against PUBLISHED consolidation tables and worked examples.26 passing
Analyses validated: coupled-consolidation
- Passthe FE run completed without a time-step warning
- PassFHWA Table 7-4: Tv = 0.031 ⇒ U = 20 %
- PassFHWA Table 7-4: Tv = 0.071 ⇒ U = 30 %
- PassFHWA Table 7-4: Tv = 0.126 ⇒ U = 40 %
- PassFHWA Table 7-4: Tv = 0.197 ⇒ U = 50 %
- PassFHWA Table 7-4: Tv = 0.287 ⇒ U = 60 %
- PassFHWA Table 7-4: Tv = 0.403 ⇒ U = 70 %
- PassFHWA Table 7-4: Tv = 0.567 ⇒ U = 80 %
- PassFHWA Table 7-4: Tv = 0.848 ⇒ U = 90 %
- PassFHWA Table 7-4: Tv = 1.000 ⇒ U = 93.1 %
- PassFHWA Table 7-4: Tv = 1.500 ⇒ U = 98.0 %
- PassFHWA Table 7-4: Tv = 2.000 ⇒ U = 99.4 %
- PassFHWA Table 7-4 (pore-pressure definition): Tv = 0.197 ⇒ U = 50 %
- PassFHWA Table 7-4 (pore-pressure definition): Tv = 0.403 ⇒ U = 70 %
- PassFHWA Table 7-4 (pore-pressure definition): Tv = 0.848 ⇒ U = 90 %
- PassDas Table 2.11: Tv = 0.159 ⇒ U = 45 %
- PassDas Table 2.11: Tv = 0.477 ⇒ U = 75 %
- PassDas Table 2.11: Tv = 0.684 ⇒ U = 85 %
- PassDas Table 2.11: Tv = 1.129 ⇒ U = 95 %
- PassDas Table 2.11: Tv = 1.781 ⇒ U = 99 %
- PassFHWA Example 7-3: t90 = 424 days (single drainage, Hd = 10 ft, cv = 0.2 ft²/day)
- PassCraig Example 4.2: upper clay (mv = 0.35 m²/MN, Δσ′ = 82 kPa, H = 3 m) settles 86.1 mm
- PassCraig Example 4.2: lower clay (mv = 0.13 m²/MN, Δσ′ = 77 kPa, H = 3 m) settles 30.0 mm
- PassCraig Example 4.7: mv = 0.25 m²/MN, Δσ′ = 65 kPa, H = 10 m gives a final settlement of 162 mm
- PassDas Example 2.13: k = 1.303e-7 m/min with mv = 0.00108 m²/kN gives cv = 1.23e-5 m²/min
- PassDas Example 2.12 (lab specimen): 25.4 mm double-drained, cv = 7.061 mm²/min ⇒ t50 = 4.5 min
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
cv-oedometer-web-validationrecords a differenceWeb-benchmark validation for `cv-oedometer` — coefficient of consolidation from an oedometer time–compression curve.11 passing
Analyses validated: cv-oedometer
- Pass[IS 2720-15 §6.1.2.4] the log-time time factor is 0.197
- Pass[IS 2720-15 §6.1.1.5] the root-time time factor is 0.848
- Pass[Craig 4.3] log-time method reproduces the published c_v = 0.45 m²/year
- Pass[Craig 4.3] root-time method reproduces the published c_v = 0.46 m²/year
- Pass[Craig 4.3 + IS 2720-15] the drainage path is HALF the specimen thickness
- Pass[Craig 4.3] the two methods agree on the same specimen to within 1.3%
- Pass[Craig 4.3] permeability from c_v·m_v·γw reproduces k = 1.0e-10 m/s
- Passk is null, not zero, when m_v is not supplied
- Passc_v scales with the square of the drainage path, per the closed form
- Passa cleared fitting time is refused rather than producing a huge c_v
- Passan oedometer drainage path in metres is flagged as a units error
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
differential-settlement-ec7-web-validationDifferential settlement — the **EUROPEAN** check, validated against **EN 1997-1:2004 Annex H**, *"Limiting values of structural deformation and foundation movement"*.6 passing
Analyses validated: differential-settlement
- PassEN 1997-1 Annex H (2) — the published rotation range 1/2000 … 1/300, with 1/500 the general value
- PassEN 1997-1 Annex H (3) — hogging HALVES the acceptable ratio
- Passthe Annex H check applied end to end, at the published thresholds
- PassAnnex H is reported as INFORMATIVE guidance, not as a normative limit
- Passthe three-state assessable flag is honoured — no verdict on no data
- Passthe SAME site can be judged under both standards, and they differ meaningfully
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
differential-settlement-web-validationC.DIFF — `differential-settlement` web-benchmark against IS 1904:1986 Table 1, 72 cited values (24 cells × 3 quantities).6 passing
Analyses validated: differential-settlement
- PassC.DIFF.1: all 24 cells of IS 1904:1986 Table 1 match the engine transcription
- PassC.DIFF.2: the steel row is 0.0033L in ALL four columns (the OCR near-miss)
- PassC.DIFF.3: the differential coefficient is consistent with the angular limit
- PassC.DIFF.4: checkIS1904 applies the published limits to a computed settlement pattern
- PassC.DIFF.5: the "not likely to be encountered" cells report applicable:false, not a pass
- PassC.DIFF.6: E-6/Q-1 regression — one point must NOT report a pass
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
elastic-settlement-web-validationrecords a differenceelastic-settlement — dedicated web-benchmark against PUBLISHED values.9 passing
Analyses validated: elastic-settlement
- PassBowles (1997) Table 5-2 — Steinbrenner I1 (=F1) and I2 (=F2), fourteen printed cells
- PassDas (2016) Tables 7.2 / 7.3 — cells at n′ values Bowles does not tabulate
- PassBaban (2016) Problem 3.2 (= Das Example 7.2 re-solved): rigid 1×2 m footing, centre
- PassBaban (2016) Problem 3.3: same footing, Es,av = 8 500 kPa over H = 4 m (=4B)
- PassDas (2016) Example 7.2 — the table reads (not the mis-added Is of the printed solution)
- PassBowles (1997) Example 5-7 — raft of the "Savings Bank Building", centre
- PassBowles (1997) Example 5-13 — ring footing idealised as a 3.658 m square, H = 5B′
- PassBowles (1997) §5-6: rigid-base reduction and the half-space limit
- Passclosed-form sanity: engine Is reduces to F1 + (1−2μ)/(1−μ)·F2 and S = m·q·B′·(1−μ²)/Es·Is·IF
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
embankment-stress-web-validationembankment-stress — dedicated web-benchmark against PUBLISHED values.4 passing
Analyses validated: embankment-stress
- PassIllinois DOT (2015) Geotechnical Manual Table D.8-1 — Osterberg influence values for stated a/z, b/z
- PassDas (2016) Example 6.8 — 7 m embankment, γ = 17.5 kN/m³, crest 5 m, 2H:1V slopes: stress under the centreline at z = 5 m
- PassHoltz & Kovacs (1981) Example 8.21 — 3 m highway embankment, ρ = 2.0 Mg/m³, 10 m crest, 2H:1V slopes
- PassSurface limit and the vertical-face (strip) limit — Das Fig 6.18 axis, H&K text, Das Table 6.3
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
expansive-heave-web-validationrecords a differenceValidation for `expansive-heave` — swell-index heave of an expansive clay, ΔH = Cs·H/(1+e0)·log10(p_s/σ'), zero when σ' ≥ p_s (`expansive-heave.ts`, `computeExpansiveHeave`).4 passing
Analyses validated: expansive-heave
- PassTerzaghi–Peck–Mesri Art. 16.10: 1-m sublayer, p_s = 3000 kPa, C_εs = 0.036, σ'_vo = 45 kPa ⇒ heave 66 mm
- PassTerzaghi–Peck–Mesri Table 16.2: swelling from p_s(e=1.0) to p_s(e=1.5) changes the void ratio by 0.5
- PassTerzaghi–Peck–Mesri Art. 16.10: no heave once the final stress reaches the swelling pressure
- PassFredlund & Rahardjo (1993) Eq. 8.34: strain is linear in C_s/(1+e0) and in log(P_f/P_o)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
expansive-soil-web-validationWeb-benchmark validation for `expansive-soil` — swelling-soil classification, heave, and the mitigation ladder.11 passing
Analyses validated: expansive-soil
- PassFSI severity breaks at the published 20 / 35 / 50 % edges (IS 2720-40)
- PassPI severity breaks at the published 15 / 35 / 55 % edges (IS 1498 Annex C)
- Passswell-pressure severity breaks at the published 50 / 150 / 300 kPa edges (IS 2720-41)
- Passthe governing severity is the worst of the three indices
- Passindices that disagree sharply are flagged for re-testing
- Passrecommended foundation depth is the active zone + 0.3 m, or deeper if founded deeper
- Passheave follows Δh = Σ Cs/(1+e0)·H·log10(σ′sw/σ′f), integrated over the active zone
- Passsurcharge that exceeds the swell pressure suppresses heave entirely
- Passheave needs Cs, e0 AND a swell pressure — a partial set is refused with a reason
- Passthe mitigation ladder escalates with severity and cites its standards
- Passa very high severity under a building escalates to piles, and rationale is cited
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
gibson-consolidation-layered-terzaghi-web-validationWEB-VALIDATION for the finite-strain (Gibson) consolidation engine — the SMALL-STRAIN LIMIT against Terzaghi's published time-factor table, plus the LAYERED interface physics.13 passing
Analyses validated: gibson-consolidation, gibson-consolidation-layered
- PassGibson Terzaghi-limit setup: strain is small (< 0.5%) and solids are conserved
- PassGibson → Terzaghi limit: U = 20% at T_v = 0.0314 (Das Table 2.11)
- PassGibson → Terzaghi limit: U = 30% at T_v = 0.0707 (Das Table 2.11)
- PassGibson → Terzaghi limit: U = 40% at T_v = 0.126 (Das Table 2.11)
- PassGibson → Terzaghi limit: U = 50% at T_v = 0.197 (Das Table 2.11)
- PassGibson → Terzaghi limit: U = 60% at T_v = 0.286 (Das Table 2.11)
- PassGibson → Terzaghi limit: U = 70% at T_v = 0.403 (Das Table 2.11)
- PassGibson → Terzaghi limit: U = 80% at T_v = 0.567 (Das Table 2.11)
- PassGibson → Terzaghi limit: U = 90% at T_v = 0.848 (Das Table 2.11)
- PassGibson → Terzaghi limit: t₉₀/t₅₀ = 0.848/0.197 = 4.305 (c_v cancels)
- PassGibson → Terzaghi limit: t₅₀/t₃₀ = 0.197/0.0707 = 2.786 (c_v cancels)
- PassGibson → Terzaghi limit: doubling the drainage path quadruples t₅₀ and t₉₀
- PassGibson layered: the layered path also degenerates to the Terzaghi table at U = 50% and 90%
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
gibson-consolidation-layered-web-validationWEB-BENCHMARK validation for the LAYERED finite-strain (Gibson) consolidation option (per-layer C_c / C_k / e₀ / k₀; the interface flux is written in the CONTINUOUS effective-stress gradient with a harmonic-mean permeability, since the voi…9 passing
Analyses validated: gibson-consolidation, gibson-consolidation-layered
- PassGibson layered REDUCTION-2: identical 2-layer stack ≡ single material (ultimate + final)
- PassGibson layered REDUCTION-3: identical unequal 3-layer stack ≡ single material
- PassGibson layered BOUND: soft/stiff column lies between all-soft and all-stiff bounds
- PassGibson layered CONTINUITY: at equilibrium σ′ is continuous, e is discontinuous at the interface
- PassGibson layered TREND: soft-at-bottom settles more than soft-at-top
- PassGibson layered TREND: a lower-k layer slows consolidation (less consolidated at a fixed time)
- PassGibson layered EXACT: solids-mass conserved for layered profiles
- PassGibson layered WEB (Terzaghi limit): stiff small-strain column consolidates fully & monotonically
- PassGibson layered WEB (Townsend-McVay geometry): solids height invariant + void-space bound
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
gibson-consolidation-small-strain-web-validationPUBLISHED-VALUES(gibson-consolidation): 16 -- distinct published values for this engine (engine-level total, declared once); independent audit A3: 16-18 distinct published values; declared at the lower bound.18 passing
Analyses validated: gibson-consolidation, gibson-consolidation-layered
- PassTerzaghi corner is a valid small-strain run (precondition for every comparison below)
- PassFHWA Table 7-4: U = 20 % at Tv = 0.031
- PassFHWA Table 7-4: U = 30 % at Tv = 0.071
- PassFHWA Table 7-4: U = 40 % at Tv = 0.126
- PassFHWA Table 7-4: U = 50 % at Tv = 0.197
- PassFHWA Table 7-4: U = 60 % at Tv = 0.287
- PassFHWA Table 7-4: U = 70 % at Tv = 0.403
- PassFHWA Table 7-4: U = 80 % at Tv = 0.567
- PassFHWA Table 7-4: U = 90 % at Tv = 0.848
- PassFHWA Table 7-4: the engine reports t90 itself consistently with Tv = 0.848
- PassFHWA Table 7-4: Tv = 1.000 ⇒ U = 93.1 % (printed to 0.1 %)
- PassFHWA Table 7-4: Tv = 0.197 ⇒ U = 50 %
- PassFHWA Table 7-4 ratio t90/t50 = 0.848/0.197 (cv and H cancel)
- PassFHWA Table 7-4 ratio t80/t40 = 0.567/0.126 (cv and H cancel)
- PassFHWA Example 7-3: t90 = 0.848·(10 ft)²/0.2 ft²/day = 424 days
- PassDas Example 2.12: 45.7 % consolidation after 31.6 days
- PassDas Example 2.12: at the published 31.6 days the engine has consolidated 45.7 %
- PassCraig Example 4.7: Tv = 0.0235 after 6 months ⇒ Uv = 0.17
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
gibson-consolidation-web-validationWEB-BENCHMARK validation for the finite-strain (Gibson) consolidation engine.10 passing
Analyses validated: gibson-consolidation, gibson-consolidation-layered
- PassGibson web EXACT1: solids-mass conservation (Hs = H0/(1+e0) invariant)
- PassGibson web EXACT2: ultimate settlement ≤ void-space bound H0 − Hs
- PassGibson web EXACT3: consolidation time scales as 1/k₀ (halve k₀ ⇒ 2× t₉₀)
- PassGibson web EXACT4: Townsend-McVay phosphate clay — solids height 0.6076 m invariant
- PassGibson web BENCHMARK4b: power-law reproduces Townsend-McVay ultimate settlement ≈ 5.44 m
- PassGibson web TREND5: surcharge deepens settlement
- PassGibson web TREND6: for fixed H0, lower e0 (denser) ⇒ more self-weight settlement
- PassGibson web TREND7: monotonic settlement, converges to ~100% given time
- PassGibson web TREND8: bottom consolidates more than the drained top
- PassGibson verdict: names ultimate settlement + degree of consolidation
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hs-confined-settlement-web-validationValidation for the Hardening-Soil confined settlement engines (`hs-confined-settlement.ts`: `computeHsConfinedSettlement` — slug `hs-confined-settlement`; `computeHsLayeredSettlement` — slug `hs-layered-settlement`).17 passing
Analyses validated: hs-confined-settlement, hs-layered-settlement
- Pass[1] the engine's OWN closed-form analytic settlement matches the hand-derived Schanz-Vermeer-Bonnier oedometer integral exactly
- Pass[2] the nonlinear FE (two-surface plasticity) settlement matches the closed-form analytic integral within the engine's own documented 2% tolerance
- Pass[3] the closed-form checks out at a second, independent input set (thinner layer, stiffer clay, higher increment)
- Pass[4] preconsolidated (OCR>1) soil settles LESS than the equivalent normally-consolidated soil, per the HS stiff-unload-reload branch
- Pass[5] the linear-elastic (initial-modulus) estimate OVER-predicts settlement relative to the true HS response, because HS stiffness increases with stress while the linear estimate holds it fixed at the (lower) initial value
- Pass[6] applied_load_kpa=0 gives exactly zero settlement, labelled definitional
- Pass[7] invalid HS parameters (zero stiffness, phi outside (0,90), m outside [0,1]) are refused
- Pass[8] a two-layer profile's total settlement equals the sum of its per-layer settlements exactly
- Pass[9] the total thickness reported equals the sum of the input layer thicknesses exactly
- Pass[10] the dominant layer index correctly identifies the layer with the largest settlement contribution
- Pass[11] an empty layer list, or applied_load_kpa < 0, is refused
- PassCraig Ex 4.5 (p. 132): m_v 0.94 m²/MN, Δσ′ 14.7 kPa, H 8 m → 110 mm
- PassDas Ex 2.12: NC clay 2.8 m, σ′₀ 140 → 212 kN/m², e 0.92 → 0.86 → S_c = 87.5 mm
- PassFHWA Ex 7-3 (p. 7-37): NC clay 10 ft, C_c 0.5, e₀ 1.0, 600 → 3000 psf → ΔH = 1.75 ft
- PassCraig Ex 4.2 (p. 112): layered embankment settlement 86.1 + 30.0 = 116.1 mm
- Passseating regression: stiff soil at low σ′v0 — FE tracks the closed form within 3 % (was 55× too small, 2× too large, 0)
- Passthe published-value tally is 6 distinct printed numbers; PARTIAL (short of 20 by 14 per engine)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
is8009-settlement-web-validationis8009-settlement — dedicated web-benchmark against PUBLISHED values.5 passing
Analyses validated: is8009-settlement
- PassCraig (2012) Example 8.5 / Table 8.7 — five 3 m layers under the centre of a 6 m square footing, q = 160 kPa
- PassDas (2016) Table 6.5 — centre-of-rectangle influence factor Ic (= engine I_B), fourteen cells
- PassDas (2016) Example 6.2 — 2.5 × 5 m footing, 150 kPa, z = 6.25 m below the centre
- PassBowles (1997) Example 5-3 — 800 kN on a 2 × 2 m footing (q = 200 kPa): stress under the centre
- PassIS 8009 (Part 1):1976 Cl 9.5.2 — rigidity factor 0.8 on the centre settlement
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
janbu-settlement-web-validationWEB-BENCHMARK validation for the Janbu tangent-modulus settlement engine.23 passing
Analyses validated: janbu-settlement
- PassV1 (§5): crust layer settlement 2.35 cm (published 2.35)
- PassV2 (§5): clay layer settlement 39.26 cm (published 39.26)
- PassV3 (§5): sand layer settlement 1.93 cm (published 1.93)
- PassV4 (§5): total settlement 43.5 cm (Settle3 published; Janbu 1963 43.6)
- PassV5 (§5): discretization converges — n=20 closer to published than n=1
- PassV6 (Eq 3.9): a=1 till m=500 → ε = Δσ/(m·σ′r) = 0.002 → 2.0 mm
- PassV7 (Eq 3.11): a=0.5 dense sand m=400 → (√200−√100)/(5·400) = 2.071 mm
- PassV8 (Eq 3.11): a=0.5 compact sand m=250 → (√200−√100)/(5·250) = 3.314 mm
- PassV9 (Eq 3.11): a=0.5 loose sand m=100 → (√200−√100)/(5·100) = 8.284 mm
- PassV10 (Eq 3.15): a=0 soft silty clay m=10 → (1/10)·ln2 = 69.31 mm
- PassV11 (Eq 3.15): a=0 soft marine clay m=5 → (1/5)·ln2 = 138.63 mm
- PassV12 (Eq 3.15): a=0 peat m=2 → (1/2)·ln2 = 346.57 mm (softest Table 3.1 soil)
- PassV13 (Eq 3.11): a=0.5 silt m=200 → (√200−√100)/(5·200) = 4.142 mm
- PassV14 (Eq 3.11): a=0.5 at lower stress σ0=50, m=250 → (√150−√50)/(5·250) = 4.141 mm
- PassV15: a=0.5 settles MORE at lower initial stress (modulus ∝ √σ′) — the Janbu non-linearity
- PassV16: a=1 settlement is independent of σ0 (constant modulus)
- PassV17: a=1 settlement scales linearly with H (elastic)
- PassV18 (Eq 3.18): a=0 with m = ln10·(1+e0)/Cc reproduces the Cc settlement exactly
- PassV19: a=1 with m = E/100 reproduces the elastic settlement Δσ·H/E
- PassV20 (Eq 3.17): OC below σ′p settles LESS than NC at the same increment (mr > m)
- PassV21 (Eq 3.16): OC crossing σ′p = recompression to σ′p + virgin beyond
- PassV22: finite-footing Δσ from the shared Boussinesq library (2×2 @ z=1 → 0.7009·q)
- PassV23: 2:1 method gives a deeper-spread, smaller near-surface Δσ than infinite
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
koppejan-settlement-web-validationWEB-BENCHMARK validation for the Koppejan settlement & time-dependent consolidation engine.23 passing
Analyses validated: koppejan-settlement
- PassV1 (§17 part 1): ultimate settlement 0.355 m (published 0.355, analytical = Settle3)
- PassV2 (§17 part 2): settlement at 1000 d 0.568 m (published 0.568, spreadsheet = Settle3)
- PassV3 (§17): at 1000 d the profile is fully consolidated (U = 1)
- PassV4 (§17): settlement at 1 d ≈ ultimate (creep term log10(1) = 0)
- PassV5 (§17): settlement at 10 d = ultimate + 1 log-cycle of creep
- PassV6 (§17): settlement at 100 d = ultimate + 2 log-cycles of creep
- PassV7 (§17): settlement at 10000 d = ultimate + 4 log-cycles of creep
- PassV8 (§17): creep increments are equal per log-cycle (secular linearity)
- PassV9 (Eq 29): Cp=10, Cs=50 ultimate ε = (1/10)·ln2 = 0.069315 → 69.31 mm
- PassV10 (Eq 29): Cp=5 ultimate doubles the primary strain → 138.63 mm
- PassV11 (Eq 29): Cp=20 ultimate halves the primary strain → 34.66 mm
- PassV12 (Eq 29): @1000d Cs=50 → (0.1 + 3/50)·ln2 = 110.90 mm
- PassV13 (Eq 29): @1000d Cs=25 → (0.1 + 3/25)·ln2 = 152.49 mm (more creep)
- PassV14 (Eq 29): @1000d Cs=100 → (0.1 + 3/100)·ln2 = 90.11 mm (less creep)
- PassV15 (Eq 29): creep per log-cycle = (1/Cs)·ln(σ′f/σ′i)·H = 13.863 mm/cycle for Cs=50
- PassV16: small Tv ⇒ U = √(4·Tv/π) (U≤60% branch); cv=0.001, H=4, Hdr=2, t=10d → U=0.0564
- PassV17: partial consolidation at intermediate time (cv=0.001, H=4, t=1000d → U=0.5642)
- PassV18: large Tv ⇒ U = 1; cv=0.5, H=4, Hdr=2, t=100d (Tv=12.5)
- PassV19: double drainage halves the drainage path ⇒ 4× faster consolidation
- PassV20 (§4.4): k = cv·γw/(Cp·σ′zi); cv=1, γw=9.81, Cp=10, σ=100 → 0.00981 m/day
- PassV21 (§4.4): k doubles with cv; k inversely proportional to Cp
- PassV22: OC below σ′p uses recompression constants ⇒ less settlement than NC
- PassV23: OC crossing σ′p combines recompression + virgin log terms
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
line-load-stress-web-validationline-load-stress — dedicated web-benchmark against PUBLISHED values.3 passing
Analyses validated: line-load-stress
- PassDas (2016) Table 6.2 — Δσ_z/(q/z) against x/z, twenty-one published values
- PassFHWA NHI-06-089 (2006) Example 10-2 — lateral pressure on a 30 ft unyielding wall from a 700 lb/ft line load 15 ft away
- PassVarghese (2005) Eq. 17.3 — the wall-pressure coefficient of the line-load horizontal stress
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
multilayer-consolidation-web-validationValidation of the multi-layer 1-D consolidation engine (`multilayer-consolidation.ts`) against PUBLISHED layered-clay settlement and time-rate examples.25 passing
Analyses validated: multilayer-consolidation
- PassFHWA Table A.6-3: Sub-layer 1 (recompression only) = 1.17 in
- PassFHWA Table A.6-3: Sub-layer 2 (Cr then Cc) = 2.55 in
- PassFHWA Table A.6-3: Sub-layer 3 (Cr then Cc) = 8.11 in
- PassFHWA Table A.6-3: clay total = 11.83 in
- PassFHWA Table A.6-6: Sub-layer 1 under embankment + surcharge = 1.93 in (book rounds terms to 0.01 ft)
- PassFHWA Table A.6-6: Sub-layer 2 under embankment + surcharge = 4.44 in
- PassFHWA Table A.6-6: Sub-layer 3 under embankment + surcharge = 10.89 in
- PassFHWA Table A.6-6: clay total under embankment + surcharge = 17.26 in
- PassFHWA Table A.6-6: the surcharge alone adds 5.43 in
- PassFHWA Table A.7-3: pier Sub-layer 1 = 0.97 in
- PassFHWA Table A.7-3: pier Sub-layer 2 (0.18 + 0.80) = 0.98 in
- PassFHWA Table A.7-3: pier clay total = 1.95 in
- PassFHWA Table A.7-6: abutment Sub-layer 1 = 0.12 in
- PassFHWA Table A.7-6: abutment Sub-layer 2 (NC, Cc) = 2.50 in
- PassFHWA Table A.7-6: abutment clay total = 2.62 in
- PassFHWA Table A.6-4: 20 % of the 35-ft clay settlement takes 16 days
- PassFHWA Table A.6-4: 50 % takes 101 days
- PassFHWA Table A.6-4: 70 % takes 206 days
- PassFHWA Table A.6-4: 90 % takes 432 days
- PassFHWA Table A.6-4 read the other way: 16 days ⇒ 20 %, 101 days ⇒ 50 %
- PassFHWA Table A.6-4 read the other way: 206 days ⇒ 70 %, 432 days ⇒ 90 %
- PassFHWA Table A.7-4: the 25-ft pier clay (Hd = 12.5 ft) reaches 20/50/70/90 % in 8/51/104/220 days
- PassFHWA Example 7-3: primary settlement of the NC clay = 1.75 ft = 21 in
- PassFHWA Example 7-3: t90 = 424 days (single drainage, Hd = 10 ft, cv = 0.2 ft²/day)
- PassLambe & Whitman Example 25.6: ρ = 4.3/(1+1.83)·(1.83 − 1.40) = 0.653 m
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pvd-design-published-web-validationValidation of the PVD / sand-drain spacing DESIGNER (`pvd-design.ts`) against PUBLISHED radial consolidation tables and PUBLISHED worked drain designs.12 passing
Analyses validated: pvd-design
- PassDas Table 16.5: n = 5
- PassDas Table 16.5: n = 10
- PassDas Table 16.5: n = 15
- PassDas Table 16.5: n = 20
- PassDas Table 16.5: n = 25
- PassDas Example 16.5: 77 % radial consolidation in 9 months with 0.2 m drains needs n = 15
- PassCraig Example 4.7: the large-diameter sand-drain target is found feasible, not refused
- PassCraig Example 4.7: spacing ratio n = 9
- PassCraig Example 4.7: square-pattern spacing S = 3.2 m
- PassHan Design Example 7.1: 1.0 m triangular spacing reproduces the published Ur at the published Tr
- PassFHWA-NHI-16-027 §4.4: ≈ 8 ft spacing for 90 % in ≈ 300 days
- PassFHWA-NHI-16-027 §4.4: ≈ 10 ft spacing for 90 % in ≈ 500 days
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pvd-design-web-validationValidation against Barron (1948) and Hansbo (1981, Proc.10 passing
Analyses validated: pvd-design, radial-consolidation
- Pass[1-2] influence diameter constants match the published Hansbo/Barron values exactly: de=1.05.S (triangular), de=1.128.S (square)
- Pass[3-4] ROUND-TRIP CONSISTENCY: the spacing solved for a 90% target, run back through the forward radialConsolidation solver, reproduces ~90% U
- Pass[5] influence diameter reported by the design matches the pattern constant times the solved spacing exactly
- Pass[6] a longer available time allows a WIDER (less conservative) spacing to reach the same target
- Pass[7] a higher target consolidation requires a TIGHTER spacing, all else equal
- Pass[8] a higher coefficient of consolidation ch allows a wider spacing for the same target/time
- Pass[9] an unreachable target (very high U, very little time) is reported as NOT feasible, not silently solved at the tightest spacing
- Pass[10] a trivially-easy target (met even at the widest practical spacing) is flagged as such, not silently solved at the tightest
- Pass[11] the U-vs-spacing curve is monotonically DECREASING (tighter spacing -> higher U, per Hansbo theory)
- Pass[12] invalid inputs (ch<=0, target outside (0,100), time<=0, dw<=0) are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
radial-consolidation-web-validationRadial consolidation by vertical drains — validated against the three papers the engine cites:7 passing
Analyses validated: radial-consolidation
- PassBarron (1948) equal-strain drain factor F(n) — 10 values across the design range
- PassHansbo (1981) smear extension — and the Barron lower-bound clamp
- Passinfluence diameter — 1.05·S triangular, 1.128·S square (the standard unit-cell equivalences)
- PassUh = 1 − exp(−8·Th/μ) end to end, with Th = ch·t/de²
- PassCarrillo (1942) — U = 1 − (1 − Uv)(1 − Uh)
- PassHansbo (1981) well resistance — the depth-averaged Fr and its sign
- Passthe audit E-22/23/24 guards hold alongside the physics
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
schmertmann-web-validationSCHMERTMANN STRAIN-INFLUENCE SETTLEMENT — web-validation benchmark.8 passing
Analyses validated: schmertmann
- PassDas Ex 7.4 — geometry of the Iz diagram (Eqs 7.21-7.24): 4 published values
- PassDas Ex 7.4 — Es = 2.8 qc for L/B = 2 (Eq 7.27), and the correction factors
- PassDas Ex 7.4 — Σ Iz/Es·Δz = 17.52e-5 and Se = 27.83 mm
- PassE-60 — the answer must not depend on how the caller binned the CPT
- PassE-59 — Es for a rectangle is logarithmic in L/B, not linear in (L/B−1)/9
- Passthe Iz diagram degenerates correctly at the square and strip limits
- Passthe published interpolation relations are slightly NON-monotone in L/B — recorded, not corrected
- PassC1 and C2 behave as Eqs (7.20) define them
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
secondary-compression-web-validationWEB-BENCHMARK validation for the isotache / secondary-compression (creep) engine.25 passing
Analyses validated: secondary-compression
- Passcreep 1: Cαε=0.05, H=5, t_p=1→t2=100 yr ⇒ 500 mm (2 log-cycles)
- Passcreep 2: same, t2=50 yr ⇒ 424.74 mm
- Passcreep 3: same, t2=10 yr ⇒ 250 mm (1 log-cycle = Cαε·H)
- Passcreep 4: Das NC-clay Cα=0.02, e_p=0.766, H=3, t_p=1.5→t2=15 ⇒ 33.98 mm
- Passcreep 5: Das clay, t2=6.5 yr ⇒ 21.63 mm
- Passcreep 6: inorganic Cα=0.008, e_p=0.9, H=4, t_p=2→t2=20 ⇒ 16.84 mm
- Passcreep 7: inorganic, t2=50 ⇒ 23.55 mm
- Passcreep 8: t2 = t_p ⇒ 0 mm (creep starts only after primary)
- Passcreep 9: settlement scales linearly with H
- Passt_p 10: cv=5 m²/yr, H=10, single drainage ⇒ t_p = 1.129·100/5 = 22.58 yr
- Passt_p 11: double drainage halves H_dr ⇒ t_p = 5.645 yr (¼ of single)
- Passt_p 12: no cv ⇒ falls back to the input t_p
- PassSSC 13: μ* = Cα/(ln10·(1+e)); Cα=0.04, e=1 ⇒ 0.008686
- PassSSC 14: λ* = Cc/(ln10·(1+e)); Cc=0.485, e=1 ⇒ 0.1053 (≈ Soft-Soil-Creep (Vermeer & Neher 1999) preset λ*=0.1055)
- PassSSC 15: κ* = 2·Cr/(ln10·(1+e)); Cr=0.05, e=1 ⇒ 0.02172
- Passrate 16: dS/dt = Cαε·H·1000/(ln10·t2); base @100 yr ⇒ 1.086 mm/yr
- Passrate 17: rate decreases with time (creep decelerates)
- Passfingerprint 18: Cα/Cc=0.04 ⇒ inorganic clay, consistent
- Passfingerprint 19: peat Cα/Cc≈0.06 ⇒ peat/organic band
- Passfingerprint 20: Cα/Cc=0.15 ⇒ flagged inconsistent (outside 0.02–0.10)
- Passsurcharge 21: R_s′>0 reduces creep vs no surcharge (t_l = 100·t_p·R_s′^1.7)
- Passsurcharge 22: if t_l > design life ⇒ zero creep, ~100 % eliminated
- Passsurcharge 23: no surcharge ⇒ eliminated 0 %, settlement unchanged
- Passsurcharge 24: peat uses t_l = 10·t_p·R_s′ (linear, not power 1.7)
- Passverdict 25: below the limit ⇒ ACCEPTABLE; above ⇒ recommends a surcharge
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
settlement-is8009-web-validationC.SET8009 — `settlement` web-benchmark against IS 8009 (Part 1):1976.6 passing
Analyses validated: settlement
- PassC.SET8009.1: rigidity factor is exactly 0.8 — IS 8009-1 Cl 9.5.2 Eq (13)
- PassC.SET8009.2: depth factor — Cl 9.5.1 / Fig 12 endpoints and monotonicity
- PassC.SET8009.3: primary consolidation follows the Terzaghi 1-D law (Cl 9.3.3)
- PassC.SET8009.4: IS 8009 prescribes Boussinesq — both stress paths are available and differ
- PassC.SET8009.5: the corrected citation is what the engine now reports at runtime
- PassC.SET8009.6: IS 1904 serviceability guidance is surfaced past 75 mm
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
settlement-worked-examples-web-validationsettlement — FULL WORKED EXAMPLES (the ≥20-value gate).33 passing
Analyses validated: settlement
- Pass[DAS] Ex 2.12 primary consolidation Sc = 87.5 mm
- Pass[DAS] Ex 2.12 at t = 31.6 days U = 45.7 % (S = 40 mm)
- Pass[DAS] Problem 2.13 (NC): Sc = 87.2 mm (Cc = 0.009(LL − 10) = 0.288, Eq. 2.54; Cs = Cc/5)
- Pass[DAS] Problem 2.14 (OC, σ′p = 128): Sc = 56.69 mm (Cc = 0.009(LL − 10) = 0.288, Eq. 2.54; Cs = Cc/5)
- Pass[DAS] Ex 7.10 oedometric Sc under a 1 × 2 m footing = 46.5 mm (Boussinesq; Das averages Δσ by Simpson’s rule)
- Pass[DAS] Ex 7.11 secondary compression t 1.3 → 6.3 yr, C′α = Cα/(1 + ep) → Ss = 19.4 mm
- Pass[CRAIG] Ex 4.6 final consolidation settlement = 182 mm
- Pass[CRAIG] Ex 4.6 settlement after 3 yr (corrected t = 2.5 yr, half-closed) = 61 mm
- Pass[CRAIG] Ex 8.5 Boussinesq corner factor at z = 1.5 m below base: Iqr = 0.233
- Pass[CRAIG] Ex 8.5 Boussinesq corner factor at z = 4.5 m below base: Iqr = 0.121
- Pass[CRAIG] Ex 8.5 Boussinesq corner factor at z = 7.5 m below base: Iqr = 0.06
- Pass[CRAIG] Ex 8.5 Boussinesq corner factor at z = 10.5 m below base: Iqr = 0.033
- Pass[CRAIG] Ex 8.5 Boussinesq corner factor at z = 13.5 m below base: Iqr = 0.021
- Pass[BOW] Table 5-2 Steinbrenner N = 0.2, M = 1: I1 = 0.009, I2 = 0.041
- Pass[BOW] Table 5-2 Steinbrenner N = 0.4, M = 1.5: I1 = 0.028, I2 = 0.071
- Pass[BOW] Table 5-2 Steinbrenner N = 0.6, M = 2: I1 = 0.055, I2 = 0.092
- Pass[BOW] Table 5-2 Steinbrenner N = 0.8, M = 1.2: I1 = 0.1, I2 = 0.09
- Pass[BOW] Table 5-2 Steinbrenner N = 1, M = 1: I1 = 0.142, I2 = 0.083
- Pass[BOW] Table 5-2 Steinbrenner N = 1.5, M = 1.7: I1 = 0.217, I2 = 0.102
- Pass[BOW] Table 5-2 Steinbrenner N = 2, M = 1.4: I1 = 0.292, I2 = 0.083
- Pass[BOW] Table 5-2 Steinbrenner N = 3, M = 2: I1 = 0.402, I2 = 0.084
- Pass[BOW] Table 5-2 Steinbrenner N = 4, M = 1: I1 = 0.408, I2 = 0.037
- Pass[BOW] Table 5-2 Steinbrenner N = 5, M = 1.5: I1 = 0.496, I2 = 0.045
- Pass[BOW] Table 5-2 Steinbrenner N = 6, M = 1.8: I1 = 0.55, I2 = 0.045
- Pass[BOW] Table 5-2 Steinbrenner N = 8, M = 2: I1 = 0.611, I2 = 0.038
- Pass[BOW] Table 5-2 Steinbrenner N = 10, M = 1.3: I1 = 0.554, I2 = 0.02
- Pass[BOW] Table 5-2 Steinbrenner N = 20, M = 1.9: I1 = 0.69, I2 = 0.015
- Pass[DAS] Ex 7.2 Steinbrenner at m′ = 2, n′ = 10: F1 = 0.641, F2 = 0.031
- Pass[BOW] Ex 5-7 raft: M = 1.2, N = 0.7, μ = 0.35 → Is = 0.121; flexible centre ΔH = 16.5/IF(0.95) = 17.4 mm
- Pass[BOW] Ex 5-14 OC clay (Cr to p′c, Cc beyond), Boussinesq through the layer → ΔH = 1.14 in (Bowles uses a layer-average Δp; ±5 %)
- Pass[NHI] NHI-06-088 Ex 7-3 embankment on NC clay: ΔH = 0.53 m
- Pass[NHI] NHI-06-088 Ex 7-3 single drainage: t90 = 424 days
- Pass[NHI] NHI-06-089 Ex 8-3 footing on NC clay, 2:1 at clay mid-depth: ΔH = 1.1 in
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
strip-load-stress-web-validationstrip-load-stress — dedicated web-benchmark against PUBLISHED values.3 passing
Analyses validated: strip-load-stress
- PassDas (2016) Table 6.3, 2x/B = 0 column — Δσ/q0 against 2z/B, twenty-one published values
- PassFHWA NHI-06-088 (2006) Example 2-2 — 5 ft strip footing, 1 000 psf: stress under the centreline from the isobar chart
- PassVarghese (2005) §3.8.1 / Eq. 3.10 — the strip subtends 90° at a depth of B/2; stress ratio there is (π/2 + 1)/π
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
vacuum-preload-web-validationValidation of the VACUUM PRELOADING engine (`vacuum-preload.ts`) against PUBLISHED preloading settlement and PVD time-rate examples.22 passing
Analyses validated: vacuum-preload
- PassHan Example 7.1: Sc1 = 1.58 m under 4.5 m of fill (Δσ = 88.65 kPa)
- PassHan Example 7.1: Sc2 = 2.08 m under 8 m of fill (Δσ = 157.6 kPa)
- PassHan Example 7.1: Sc3 = 2.37 m under 11 m of fill (Δσ = 216.7 kPa)
- PassHan Example 7.1: Tr = 0.185 ⇒ Ur = 48.2 %
- PassHan Example 7.1: Tr = 0.423 ⇒ Ur = 77.8 %
- PassHan Example 7.1: Tr = 0.720 ⇒ Ur = 92.3 %
- PassHan Example 7.1: Tr = 0.148 ⇒ Ur = 40.9 %
- PassHan Example 7.1: Tr = 0.502 ⇒ Ur = 83.2 %
- PassHan Example 7.1: Tr = 1.145 ⇒ Ur = 98.3 %
- PassHan Example 7.1: overall Uvr = 51.0 % at 52.5 days (Uv = 5.4 % with Hdr = 6 m)
- PassHan Example 7.1: overall Uvr = 93.1 % at 204 days
- PassHan Example 7.1: settlement at 52.5 days = 0.510 × 1.58 = 0.81 m
- PassDas Table 16.5: n = 5, Tr = 0.0811 ⇒ Ur = 50 %
- PassDas Table 16.5: n = 10, Tr = 0.0704 ⇒ Ur = 30 %
- PassDas Table 16.5: n = 10, Tr = 0.4543 ⇒ Ur = 90 %
- PassDas Table 16.5: n = 15, Tr = 0.3966 ⇒ Ur = 80 %
- PassDas Table 16.5: n = 15, Tr = 0.7382 ⇒ Ur = 95 %
- PassDas Table 16.5: n = 20, Tr = 0.3392 ⇒ Ur = 70 %
- PassDas Table 16.5: n = 25, Tr = 0.2834 ⇒ Ur = 60 %
- PassDas Table 16.5: n = 25, Tr = 1.0846 ⇒ Ur = 97 %
- PassCraig Example 4.7: vertical drainage alone gives Uv = 0.17 at 6 months (half-closed, d = H = 10 m)
- PassCraig Example 4.7: the 3.2 m sand-drain layout reaches U = 85 % in about 6 months
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
vertical-stress-increase-web-validationrecords a differencevertical-stress-increase — dedicated web-benchmark against PUBLISHED values.8 passing
Analyses validated: vertical-stress-increase
- PassDas (2016) Table 6.4 — Boussinesq corner influence I(m,n), fourteen cells (5 d.p.)
- PassDas (2016) Table 6.5 — Boussinesq influence Ic under the CENTRE, ten cells (3 d.p.)
- PassDas (2016) Examples 6.2 and 6.9 — 2.5 × 5 m footing, 150 kPa, z = 6.25 m under the centre
- PassDas (2016) Table 6.8 — Westergaard corner influence Iw for ν = 0, twelve cells (4 d.p.)
- PassBowles (1997) Table 5-1 — corner Ia (3 d.p., M = B/z, N = L/z), eleven cells
- PassBowles (1997) Example 5-3 — 800 kN on a 2 × 2 m footing, q = 200 kPa
- PassBowles (1997) Eq. (5-15) programming check — Westergaard corner factor at μ = 0.45
- PassLambe & Whitman (1979) Example 8.3 and Holtz & Kovacs (1981) Example 8.18 — chart-read corner factors
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
weighted-creep-web-validationrecords a differenceweighted-creep — validation of Bligh's and Lane's creep-ratio checks against PUBLISHED safe-ratio tables and worked weir examples.25 passing
Analyses validated: weighted-creep
- PassLane 1935 (IHE thesis Table 2-2): very fine sand or silt → safe weighted-creep ratio 8.5
- PassLane 1935 (IHE thesis Table 2-2): fine sand → safe weighted-creep ratio 7
- PassLane 1935 (IHE thesis Table 2-2): medium sand → safe weighted-creep ratio 6
- PassLane 1935 (IHE thesis Table 2-2): coarse sand → safe weighted-creep ratio 5
- PassLane 1935 (IHE thesis Table 2-2): fine gravel → safe weighted-creep ratio 4
- PassLane 1935 (IHE thesis Table 2-2): coarse gravel including cobbles → safe weighted-creep ratio 3
- PassLane 1935 (IHE thesis Table 2-2): boulders with some cobbles and gravel → safe weighted-creep ratio 2.5
- PassLane 1935 (IHE thesis Table 2-2): soft clay → safe weighted-creep ratio 3
- PassLane 1935 (IHE thesis Table 2-2): hard clay → safe weighted-creep ratio 1.8
- PassMustansiriyah 2020 Table 1: light sand and mud → Bligh coefficient 18
- PassMustansiriyah 2020 Table 1: fine micaceous sand → Bligh coefficient 15
- PassMustansiriyah 2020 Table 1: coarse-grained sand → Bligh coefficient 12
- PassMustansiriyah 2020 Table 1: fine_gravel lies inside the printed Bligh range 5–9 for boulders/gravel/sand
- PassMustansiriyah 2020 Table 1: coarse_gravel lies inside the printed Bligh range 5–9 for boulders/gravel/sand
- PassMustansiriyah 2020 Table 1: boulders_gravel lies inside the printed Bligh range 5–9 for boulders/gravel/sand
- PassGarg Table 11.2: coarse gravel (3.0) and boulders (2.5) lie inside the printed Lane ranges 3.0–3.5 and 2.5–3.0
- PassMustansiriyah 2020 Eq. 9 / Lane 1935: 30 m of horizontal contact counts 10 m, 30 m of vertical counts 30 m
- PassMustansiriyah 2020 Ex 1 (Bligh): creep length 63 m, gradient 1/15.75
- PassMustansiriyah 2020 Ex 1 (Bligh): on fine sand (C = 15) the structure is "safe"
- PassMustansiriyah 2020 Ex 2 (Bligh): creep length 64 m, gradient 1/10.67
- PassMustansiriyah 2020 Ex 2 (Bligh): safe on sand mixed with boulders and gravel (C = 5…9)
- PassMustansiriyah 2020 Ex 5 (Lane): N = 52.2 m, V = 31.2 m → weighted creep length 48.6 m
- PassMustansiriyah 2020 Ex 5 (Lane): coarse sand (C = 5) → "safe against piping"
- PassLane rule "safe if H/Lw ≤ 1/C": a structure exactly at C is safe, just under it is not
- Passa cleared head is refused rather than reported as a creep ratio of 2.4e10
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Slopes and embankments — factor of safety
32 finite-element rows (7 deviations, 1 recorded, 2 superseded) · 0 closed-form problems · 18 validation suites
Finite-element solver registry
Showing 32 of 32 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
drained / undrained embankment + safety factor plaxis-2d-tut2 | — | — | — | Ours —Published —— | Superseded | |
| ||||||
SR-FELA factor of safety, lower / upper bound (ACADS 1(a), homogeneous slope) k5c-acads-1a-fela-bounds | lower: 0.9769; upper: 0.9879; errorPct: 0.56 | 0.981 | — | Ours lower: 0.9769; upper: 0.9879; errorPct: …Published 0.981— | Pass | |
| ||||||
LEM critical-circle factor of safety: Bishop / Spencer / Morgenstern–Price k5c-acads-1a-lem | bishop: 0.9851; spencer: 0.9841; morgenstern-price: 0.984 | 0.986 | −0.20 % | Ours bishop: 0.9851; spencer: 0.9841; morgens…Published 0.986−0.20 % | Pass | |
| ||||||
SR-FELA factor of safety, lower / upper bound (ACADS 1(c), three soils, inclined boundaries) k5c-acads-1c-fela-bounds | lower: 1.3443; upper: 1.3623; errorPct: 0.67 | 1.359 | — | Ours lower: 1.3443; upper: 1.3623; errorPct: …Published 1.359— | Pass | |
| ||||||
LEM critical-circle factor of safety: Bishop / Spencer / Morgenstern–Price k5c-acads-1c-lem | bishop: 1.4027; spencer: 1.372; morgenstern-price: 1.3715 | 1.375 | −0.22 % | Ours bishop: 1.4027; spencer: 1.372; morgenst…Published 1.375−0.22 % | Pass | |
| ||||||
SR-FELA factor of safety, lower / upper bound (ACADS 1(d), kh = 0.15) k5c-acads-1d-fela-bounds | lower: 0.9669; upper: 0.9767; errorPct: 0.51 | 1.039 | −6.47 % | Ours lower: 0.9669; upper: 0.9767; errorPct: …Published 1.039−6.47 % | Deviation | |
| ||||||
LEM critical-circle factor of safety, kh = 0.15: Bishop / Spencer / Morgenstern–Price k5c-acads-1d-lem | bishop: 1.0128; spencer: 0.9891; morgenstern-price: 0.9866 | 0.991 | −0.19 % | Ours bishop: 1.0128; spencer: 0.9891; morgens…Published 0.991−0.19 % | Pass | |
| ||||||
SR-FELA factor of safety, lower / upper bound (ACADS 3(a), weak seam + water table) k5c-acads-3a-fela-bounds | lower: 1.2592; upper: 1.2622; errorPct: 0.12 | 1.265 | — | Ours lower: 1.2592; upper: 1.2622; errorPct: …Published 1.265— | Pass | |
| ||||||
LEM non-circular (path search) Spencer factor of safety k5c-acads-3a-lem-noncircular | spencer (circular): 1.5025; spencer (non-circular): 1.2629; morgenstern-price (circular): 1.4963; morgenstern-price (no… | 1.246 | +1.35 % | Ours spencer (circular): 1.5025; spencer (non…Published 1.246+1.35 % | Pass | |
| ||||||
LEM (Bishop / Spencer / M-P) and SR-FELA bounds, polyline water table k5c-arai-tagyo-16 | lem: (bishop: 1.1132; spencer: 1.1139; morgenstern-price: 1.1122); felaLower: 1.116; felaUpper: 1.1191 | 1.118 | −0.43 % | Ours lem: (bishop: 1.1132; spencer: 1.1139; m…Published 1.118−0.43 % | Pass | |
| ||||||
SR-FELA bounds and LEM, 2:1 slope φ′ 20°, c′/γH 0.05, D = 1 k5c-griffiths-lane-ex1 | felaLower: 1.3751; felaUpper: 1.3809; lem: (bishop: 1.3781; spencer: 1.3758; morgenstern-price: 1.3756) | 1.38 | — | Ours felaLower: 1.3751; felaUpper: 1.3809; le…Published 1.38— | Pass | |
| ||||||
factor of safety of the 1:2 embankment: SR-FELA bounds, LEM k5c-plaxis-phic-vs-bishop | felaLower: 1.5342; felaUpper: 1.5419; lem: (bishop: 1.5419; spencer: 1.5389; morgenstern-price: 1.5386) | 1.534 | −0.13 % | Ours felaLower: 1.5342; felaUpper: 1.5419; le…Published 1.534−0.13 % | Pass | |
| ||||||
factor of safety with the crest load: SR-FELA bounds, LEM k5c-plaxis-phic-vs-bishop-loaded | felaLower: 1.2551; felaUpper: 1.2625; lem: (bishop: 1.2721; spencer: 1.2689; morgenstern-price: 1.2694) | 1.261 | −0.17 % | Ours felaLower: 1.2551; felaUpper: 1.2625; le…Published 1.261−0.17 % | Pass | |
| ||||||
stability number γH/cu of an unsupported vertical cut (Tresca), gravity multiplier k5c-vertical-cut | lower: 3.7577; upper: 3.7927; errorPct: 0.46 | 3.772–3.7845 | — | Ours lower: 3.7577; upper: 3.7927; errorPct: …Published 3.772–3.7845— | Pass | |
| ||||||
Tutorial 2, embankment on DRAINED HS clay: uy at the crest (23,4), centre base (25,0), 2 m beyond the toe (38,0) k5b-plaxis-2d-tut2-drained | crest: -226.7; centre base: -177.9; beyond toe (38,0): 0.6 | —mm | — | Ours crest: -226.7; centre base: -177.9; beyo… mmPublished — mm— | Recorded, no published value | |
| ||||||
Tutorial 2, embankment on UNDRAINED (A) HS clay: construction completes k5b-plaxis-2d-tut2-undrained | 1ΣMstage | 1ΣMstage | 0.00 % | Ours 1 ΣMstagePublished 1 ΣMstage0.00 % | Pass | |
| ||||||
factor of safety ΣMsf, embankment 1:2, no load (Analysis 1) k5a-phic-bishop-analysis1 | 1.53867 | 1.534 | +0.30 % | Ours 1.53867Published 1.534+0.30 % | Pass | |
| ||||||
factor of safety ΣMsf after a 30 kPa crest load (Analysis 2) k5a-phic-bishop-analysis2 | 1.25937 | 1.261 | −0.13 % | Ours 1.25937Published 1.261−0.13 % | Pass | |
| ||||||
factor of safety, homogeneous 2:1 slope, φ′ 20°, c′/γH 0.05, ψ 0, D = 1 k5a-gl99-example1 | 1.3412 | 1.35 | −0.65 % | Ours 1.3412Published 1.35−0.65 % | Deviation | |
| ||||||
factor of safety, undrained (φu = 0) 2:1 slope on a foundation, cu/γH 0.25, D = 2, homogeneous k5a-gl99-example3 | 1.45234 | 1.47 | −1.20 % | Ours 1.45234Published 1.47−1.20 % | Pass | |
| ||||||
factor of safety ΣMsf, embankment on drained clay (Phase 3) k5a-tut2-safety-drained | 1.84688 | 1.8 | +2.60 % | Ours 1.84688Published 1.8+2.60 % | Pass | |
| ||||||
factor of safety ΣMsf, embankment on undrained (A) clay (Phase 4) k5a-tut2-safety-undrained | 1.14911 | 1.4 | −17.9 % | Ours 1.14911Published 1.4−17.9 % | Superseded | |
| ||||||
Tutorial 2 as ONE project (Phase 2 changes the clay to its undrained (A) copy — per-phase material change); ΣMsf of the Safety phases 3 (drained) / 4 (undrained), real Hardening Soil → Mohr–Coulomb at frozen start stiff… k5d-plaxis-2d-tut2-safety | drained: 1.8563; undrained (phase 2 completed under the default policy — the PLAXIS-comparable value): 1.3814 | drained: 1.8; undrained: 1.4 | drained: 3.13; undrained: -1.33 % | Ours drained: 1.8563; undrained (phase 2 comp…Published drained: 1.8; undrained: 1.4drained: 3.13; undrained: -1.33 % | Pass | |
| ||||||
Tutorial 2 Phase 2: embankment construction on UNDRAINED (A) HS clay — ΣMstage reached; uy crest (23,4) / centre base (25,0) / beyond the toe (38,0); max p_excess k5d-plaxis-2d-tut2-undrained-construction | default policy (strict, then the PLAXIS criterion with the initial stiffness — D124 + D684): (ΣMstage: 1; uy crest mm:… | completes (ΣMstage 1); toe heave, p_excess highest under the embankment (figures) | — | Ours default policy (strict, then the PLAXIS …Published completes (ΣMstage 1); toe heave, p_exce…— | Pass | |
| ||||||
SCMEP soft-clay embankment, Soft Soil (USTUTT set): centreline settlement after undrained construction / after 100 years, p_excess at (0, −2.5) k5d-benchmark-embankment-soft-clay | tol 1e-8 (530 T15, 9 Nov 2026): after the D557 mesh change layer 1 stops at ΣMstage 0.8515 (92 steps); settlement (0,0)… | other models after construction: 0.11–0.24 m; after 100 years: 1.10–1.60 m | — | Ours tol 1e-8 (530 T15, 9 Nov 2026): after th… m, kPaPublished other models after construction: 0.11–0.… m, kPa— | Deviation | |
| ||||||
ΣMsf of the Safety phase after the second excavation (phase 3) k5d1-plaxis-2d-tut4-safety-phase7 | — | 1.33 | — | Ours —Published 1.33— | Deviation | |
| ||||||
ΣMsf of the Safety phase after the wall and backfill (phase 6) k5d1-plaxis-2d-tut4-safety-phase8 | — | 1.83 | — | Ours —Published 1.83— | Deviation | |
| ||||||
ΣMsf of the Safety phase after the second excavation (phase 3) — PLAXIS-REPRODUCTION variant (cable strength per metre, reduced in Safety; PLAXIS-parity convergence) alg1-plaxis-2d-tut4-repro-safety-phase7 | 1.2852 | 1.33 | −3.37 % | Ours 1.2852Published 1.33−3.37 % | Deviation | |
| ||||||
ΣMsf of the Safety phase after the wall and backfill (phase 6) — PLAXIS-REPRODUCTION variant (cable strength per metre, reduced in Safety; PLAXIS-parity convergence) alg1-plaxis-2d-tut4-repro-safety-phase8 | 1.6625 | 1.83 | −9.15 % | Ours 1.6625Published 1.83−9.15 % | Deviation | |
| ||||||
Janbu simplified factor of safety on the searched critical circle (ACADS 1(a): c' 3 kPa, phi' 19.6 deg, gamma 20 kN/m3) geostudio-swv-acads-1a-janbu-simplified | 0.9351 | 0.939 | −0.42 % | Ours 0.9351Published 0.939−0.42 % | Pass | |
| ||||||
Janbu corrected (f0) factor of safety on the searched critical circle (ACADS 1(a): c' 3 kPa, phi' 19.6 deg, gamma 20 kN/m3) geostudio-swv2022-acads-1a-janbu-corrected | 0.9854 | 0.992 | −0.66 % | Ours 0.9854Published 0.992−0.66 % | Pass | |
| ||||||
Bishop factor of safety on the manual's ONE specified slip circle (simple 2h:1v slope, 10 m high, c' 5 kPa, phi' 30 deg, gamma 20 kN/m3, 29 slices, phreatic line through the toe) geostudio-hand-bishop-specified-circle | 1.2463 | 1.249 | −0.22 % | Ours 1.2463Published 1.249−0.22 % | Pass | |
| ||||||
Cited validation suites
embankment-stability-web-validationembankment-stability (embankment basal stability, `computeEmbankmentBasalStability` in `embankment-rehab.ts`) — validation against PUBLISHED values.4 passing
Analyses validated: embankment-stability
- Pass[H] Han Design Example 7.1 stage 1: γ = 19.7, cu = 24, Nc = 5.14, FS = 1.3 → H1 = 4.8 m
- Pass[H] Han Example 7.1: the 4.5 m first stage actually placed meets the required FS = 1.3
- Pass[F] default Nc is the φ = 0 bearing factor 2 + π = 5.14 (FHWA Eq. 8-4; Craig qf = 5.14·cu)
- Passdefinition (hand-derived): FoS = Nc·cu/(γH + q); inputs ≤ 0 are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-slope-srm-layered-water-web-validationC.FE.1 + A.5 web-benchmark & cross-validation — multi-layer + water-table effective-stress FE strength-reduction slope stability.13 passing
Analyses validated: fe-slope-stability
- PassC.FE.1: water table at the base (elev 0) ≡ dry (u=0 everywhere)
- PassC.FE.1: two identical layers ≡ homogeneous (exact regression)
- PassC.FE.1: empty/invalid layers array falls back to the scalar soil
- PassB: Griffiths & Lane (1999) Example 1 — dry homogeneous unchanged (1.367 on the conforming mesh)
- PassC: dry homogeneous FE ↔ Bishop LEM agree within method spread
- PassD: raising the water table lowers FoS (monotonic, correct direction)
- PassD: partially-saturated FE ↔ Bishop LEM agree (same phreatic surface)
- PassD: a mid-height water table drives the slope to marginal stability — FE and LEM agree
- PassD: a fully-saturated profile fails, and FE ↔ LEM still agree
- PassE: a weak surface layer lowers FoS below the strong-homogeneous case
- PassE: a strong crust over weak clay ↔ Bishop LEM agree within spread
- PassA.5: plastic-zone + shear-strain fields are exported and sane
- PassA.5: dry slope reports no pore pressure influence; fields still present
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-slope-stability-web-validationREAL PUBLISHED WORKED EXAMPLE (not formula-fidelity -- an independently- published answer) from Griffiths, D.V.18 passing
Analyses validated: fe-slope-stability
- Pass[1] GL99 Example 1 geometry check: c'/(gamma.H) = 10/(20.10) = 0.05 exactly, matching the paper's stated case
- Pass[2] the FE strength-reduction FoS is within 15% of the paper's published FOS=1.4 (coarse 6-row mesh vs the paper's finer mesh; the codebase's own Morgenstern-Price limit-equilibrium cross-check gives 1.369 for the identical slope)
- Pass[3] the iteration-count signature GL99 describe (ballooning iterations near the critical SRF, the numerical fingerprint of true collapse) is reproduced
- Pass[4] a steeper slope (1:1 vs 2:1) gives a LOWER factor of safety, all else equal (monotone in slope angle, the basic physical trend)
- Pass[5] a weaker soil (lower cohesion) gives a LOWER factor of safety, all else equal
- Pass[6] a higher friction angle gives a HIGHER factor of safety, all else equal
- Pass[7] a submerged (water table at crest) slope gives a LOWER factor of safety than the dry case, per the effective-stress SRM (pore pressure reduces the normal effective stress on potential failure surfaces)
- Pass[8] invalid inputs (zero height, zero slope ratio) are refused
- Pass[9] pathological (absurdly large) geometry returns a clean error rather than crashing the process
- Pass[VAL-1] ACADS 1(a): FE strength-reduction FoS lies inside the published cross-code envelope 0.94-1.00 (lowest vendor value 0.939 .. ACADS referee 1.00)
- To do[VAL-1] ACADS 1(a): FE strength-reduction FoS within 3 % of RS2 SSR 0.99Not asserted: VAL1-FE-1: RS2 SSR 0.99 (critical SRF 0.995) is above the rigorous upper bound 0.984, so a 3 % band around it is not a correctness criterion. Default is 0.9609 after VAL1-FE-2 (was 0.9453, 4.5 % low). See MEDIUM-ACADS-REPORT.md / MEDIUM-D612-REPORT.md
- Pass[VAL-1] ACADS 1(a), rows 4: ψ = 0 FE-SRM FoS ≤ the rigorous associated upper bound 0.984 and ≥ 0.94 (conforming mesh, no staircase collapse)
- Pass[VAL-1] ACADS 1(a), rows 6: ψ = 0 FE-SRM FoS ≤ the rigorous associated upper bound 0.984 and ≥ 0.94 (conforming mesh, no staircase collapse)
- Pass[VAL-1] ACADS 1(a), rows 8: ψ = 0 FE-SRM FoS ≤ the rigorous associated upper bound 0.984 and ≥ 0.94 (conforming mesh, no staircase collapse)
- Pass[VAL-1] the slope face is a straight mesh edge: every boundary node on the face lies on the line from crest (H, H) to toe (W, 0)
- Pass[VAL1-FE-2] ACADS 1(a), rows 4: FoS within one bisection cell (1/64) of the uncapped reference 0.9824, and ≤ the Optum bound 0.984
- Pass[VAL1-FE-2] ACADS 1(a), rows 8: FoS within one bisection cell (1/64) of the uncapped reference 0.9629, and ≤ the Optum bound 0.984
- Pass[VAL1-FE-2] ACADS 1(a), rows 12: FoS within one bisection cell (1/64) of the uncapped reference 0.959, and ≤ the Optum bound 0.984
- Pass[VAL1-FE-2] ACADS 1(a): a slow-converging trial runs past the old 1 500 cap, and clear collapses stop early
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
infinite-slope-web-validationPUBLISHED-VALUES: 18 -- distinct published values for this engine (engine-level total, declared once); independent audit A3: about 18 distinct published values (Duncan & Wright is quoted through the Slide manual).15 passing
Analyses validated: infinite-slope
- Pass[C] Craig Ex. 12.3(a): φ′cv = 28° — τmob = 20.3 kPa, τf = 20.7 kPa, ULS satisfied
- Pass[C] Craig Ex. 12.3(b): φ′r = 20° — τf = 14.2 kPa, τmob unchanged, ULS NOT satisfied
- Pass[E] Example E-5, seepage parallel (ru = 0.325): published F = 1.63
- Pass[E] Example E-5, horizontal seepage (ru = 0.52): published F = 1.30
- Pass[E] Example E-5: friction term A·tanφ′/tanβ = 0.98 and 0.65; cohesion term B·c′/γH = 0.65
- Pass[E] Example E-5 chart coefficients recovered from the engine: A = 0.62 / 0.41, B = 3.1
- Pass[E] ru → pore pressure is u = ru·γ·z (Eq. E-12), the input the chart method is entered with
- Pass[L] Example 24.2: submerged slope, γb·H·cos²i — published coefficient 28.73 kN/m²
- Pass[L] Example 24.1: seepage-parallel limiting slope tan i = (γb/γt)·tanφ̄ = 0.182 → FoS = 1
- Pass[L] Example 24.1: printed c̄/γt = 0.245 is the cohesion ratio of the engine run
- Pass[D] Slide verification #79 (D&W Fig. 14.4): φ′ = 30°, 2.5H:1V → reference FoS 1.44
- Pass[D] Slide verification #81 (D&W Fig. 14.7): φ′ = 30°, 2H:1V → reference FoS 1.15
- Pass[D] FoS is independent of unit weight and depth for a dry cohesionless slope (FHWA/Slide statement)
- Pass[H] Han Eq. 2.82: γ′/γsat = 0.5 ⇒ seepage FoS = ½ · dry FoS; φ′ = 30° limiting angle ≈ 16°
- Passinput guards: β outside (0,90), φ ≥ 90, missing γsat and missing ru are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
probabilistic-slope-web-validationrecords a differenceprobabilistic-slope — dedicated validation against a PUBLISHED worked reliability example (`probabilistic-slope.ts`).8 passing
Analyses validated: probabilistic-slope
- Pass[MIT] Table 1 slope: deterministic F = 1.15 and the slope is stable
- Pass[MIT] FOSM: Var[F] = 0.0467
- Pass[MIT] FOSM: β = 0.714 and Pf = Φ(−0.714) = 0.237
- Pass[MIT] Monte Carlo: Pf ≈ 0.223 within three standard errors of the difference
- Pass[MIT] FOSM and MC agree with the note's remark that near-linearity makes all three Pf close (0.223-0.237)
- PassHAND-CHECK: σ_F equals the closed-form first-order variance (no finite-difference step bias)
- Passdefinition: β = (μ_F − 1)/σ_F and Pf = Φ(−β) (Baecher & Christian 2003 Eq. 14.3)
- Passall-zero COVs are refused (deterministic analysis dressed as reliability)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rapid-drawdown-web-validationValidation for the rapid (sudden) drawdown engine (`rapid-drawdown.ts`) — the improved Duncan-Wright-Wong three-stage method of USACE EM 1110-2-1902 App.46 passing
Analyses validated: rapid-drawdown
- PassA. Kf(φ'=30, c'=0) = tan²(45+φ/2) = 3 (EM G-7)
- PassA. Kf(φ'=35, c'=0) = tan²(45+φ/2) = 3.6902 (EM G-7)
- PassA. Kf(φ'=20, c'=0) = tan²(45+φ/2) = 2.0396 (EM G-7)
- PassA. Kf(φ'=25, c'=0) = tan²(45+φ/2) = 2.4639 (EM G-7)
- PassA. Kf(φ'=40, c'=0) = tan²(45+φ/2) = 4.5989 (EM G-7)
- PassA6. Kf with c'>0 grows with c' at fixed σ'fc (EM G-8)
- PassB1. cR=0 ⇒ d_{Kc=1} = 0 (EM G-5)
- PassB2. ψ_{Kc=1}(cR=0, φR=20, φ′=30) = atan(sinφR·cosφ′/(1−sinφR)) ≈ 24.24° (EM G-6)
- PassB3. φR = 0 ⇒ ψ = 0 and d = 0 (no undrained strength gain from an isotropic frictionless R-envelope)
- PassC1. isotropic consolidation (τc = 0) ⇒ Kc = 1 (EM G-11)
- PassC2. adding consolidation shear raises Kc above 1 (EM G-11)
- PassD1. at isotropic (Kc=1) τff = d + σ′c·tanψ (the Kc=1 envelope, EM G-9)
- PassD2. τff is bounded by the two envelopes (EM G-12 interpolation)
- PassD3. τff scales with the consolidation stress σ′c
- PassD4. τff is never negative
- PassE1. rapid drawdown REDUCES the factor of safety vs the full reservoir
- PassE2. stage-3 (min of drained/undrained) ≤ stage-2 (undrained)
- PassE3. complete drawdown is the most critical — FoS rises as the drawn-down level rises
- PassE4. stronger friction raises the rapid-drawdown FoS
- PassE5. more cohesion raises the rapid-drawdown FoS
- PassE6. the drawdown FoS ratio is reported and < 1 (drawdown always costs stability)
- PassE7. a valid critical circle and full slice table are returned
- PassE8. input guards: drawn-down level above full pool is rejected
- PassF1. Fig. G-5: Kc=1 envelope from the R-envelope (cR = 1200 psf, φR = 16°, φ′ = 30°) → d = 1379 psf, ψ = 18.2° (EM G-5/G-6)
- PassF2. Fig. G-10b/G-11: Kf = tan²(45+φ′/2) = 3.00 for φ′ = 30°, c′ = 0 (EM G-26)
- PassF3.1. Fig. G-10b slice 1 (σ′c 0.32, τc 0.08 ksf): Kc 1.71, τff(Kc=1) 1.49, τff(Kc=Kf) 0.19, τff 1.02 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.2. Fig. G-10b slice 2 (σ′c 1.44, τc 0.38 ksf): Kc 1.71, τff(Kc=1) 1.85, τff(Kc=Kf) 0.83, τff 1.49 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.3. Fig. G-10b slice 3 (σ′c 2.9, τc 0.76 ksf): Kc 1.71, τff(Kc=1) 2.33, τff(Kc=Kf) 1.67, τff 2.1 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.4. Fig. G-10b slice 4 (σ′c 3.64, τc 0.95 ksf): Kc 1.71, τff(Kc=1) 2.58, τff(Kc=Kf) 2.1, τff 2.41 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.5. Fig. G-10b slice 5 (σ′c 4.05, τc 1.06 ksf): Kc 1.71, τff(Kc=1) 2.71, τff(Kc=Kf) 2.34, τff 2.58 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.6. Fig. G-10b slice 6 (σ′c 4.45, τc 1.17 ksf): Kc 1.71, τff(Kc=1) 2.84, τff(Kc=Kf) 2.57, τff 2.75 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.7. Fig. G-10b slice 7 (σ′c 4.57, τc 1.2 ksf): Kc 1.71, τff(Kc=1) 2.88, τff(Kc=Kf) 2.64, τff 2.8 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.8. Fig. G-10b slice 8 (σ′c 4.54, τc 1.19 ksf): Kc 1.71, τff(Kc=1) 2.87, τff(Kc=Kf) 2.62, τff 2.78 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.9. Fig. G-10b slice 9 (σ′c 4.31, τc 1.13 ksf): Kc 1.71, τff(Kc=1) 2.8, τff(Kc=Kf) 2.49, τff 2.69 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.10. Fig. G-10b slice 10 (σ′c 3.66, τc 0.96 ksf): Kc 1.71, τff(Kc=1) 2.58, τff(Kc=Kf) 2.11, τff 2.42 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.11. Fig. G-10b slice 11 (σ′c 2.6, τc 0.68 ksf): Kc 1.71, τff(Kc=1) 2.23, τff(Kc=Kf) 1.5, τff 1.97 ksf (EM G-24, G-9, G-10, G-27)
- PassF3.12. Fig. G-10b slice 12 (σ′c 1.01, τc 0.27 ksf): Kc 1.71, τff(Kc=1) 1.71, τff(Kc=Kf) 0.59, τff 1.31 ksf (EM G-24, G-9, G-10, G-27)
- PassF4a. Stage-3 rule on the published tables: drained strength governs on exactly slices 1, 2 and 12 (EM §G-6e)
- PassF4b. Stage 1 (Simplified Bishop, c′ = 0, φ′ = 30°, full pool): F = 2.20 (EM Fig. G-10a, ±0.06 = 2σ of table rounding)
- PassF4c. Stage 2 (undrained τff as c, φ = 0): F = 1.52 (EM Fig. G-11a, ±0.02 = 2σ of table rounding)
- PassF4d. Stage 3 (drained strength on slices 1, 2, 12): F = 1.44 (EM Fig. G-11c, ±0.02 = 2σ of table rounding)
- PassF4e. Published ordering: F1 (2.20) > F2 (1.52) > F3 (1.44) — the THIRD stage governs
- PassF5. End-to-end on the EM slope (2.84:1 average face, 110 ft, γ 135 pcf, pool 103 → 24 ft): third stage governs and the critical FoS lies at or below the EM non-critical-circle 1.44
- PassG1. full pool to the crest, c′ = 0: full-pool minimum → tanφ′/tanβ (DWB 2014 Ch. 6), independent of slices and R-envelope
- PassG2. the screen default (H 15, β 22°, c′ 5, φ′ 28°): full-pool FoS stable within 1.5 % from 10 to 60 slices and with φR
- PassG3. no drawdown, a pool above the crest, a level below the toe, negative c′ / cR and an emptied slice count are refused with no numbers
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
seepage-slope-stability-web-validationWEB-BENCHMARK validation for the coupled steady-seepage → slope-stability engine (the release rules ≥20 cited-value gate).36 passing
Analyses validated: seepage-slope-stability
- PassInf-slope DRY c'=0: FoS = tanφ/tanβ φ=30° β=20° (Skempton-DeLory 1957)
- PassInf-slope DRY c'=0: FoS = tanφ/tanβ φ=35° β=25° (Skempton-DeLory 1957)
- PassInf-slope DRY c'=0: FoS = tanφ/tanβ φ=32° β=18° (Skempton-DeLory 1957)
- PassInf-slope DRY c'=0: FoS = tanφ/tanβ φ=28° β=22° (Skempton-DeLory 1957)
- PassInf-slope DRY c'=0: FoS = tanφ/tanβ φ=40° β=30° (Skempton-DeLory 1957)
- PassInf-slope DRY c'=0: FoS = tanφ/tanβ φ=25° β=15° (Skempton-DeLory 1957)
- PassInf-slope SEEPAGE-PARALLEL c'=0: FoS = (γ'/γsat)·tanφ/tanβ φ=30° β=20° (Craig/Das)
- PassInf-slope SEEPAGE-PARALLEL c'=0: FoS = (γ'/γsat)·tanφ/tanβ φ=35° β=25° (Craig/Das)
- PassInf-slope SEEPAGE-PARALLEL c'=0: FoS = (γ'/γsat)·tanφ/tanβ φ=32° β=18° (Craig/Das)
- PassInf-slope SEEPAGE-PARALLEL c'=0: FoS = (γ'/γsat)·tanφ/tanβ φ=34° β=24° (Craig/Das)
- PassInf-slope SEEPAGE-PARALLEL c'=0: FoS = (γ'/γsat)·tanφ/tanβ φ=30° β=15° (Craig/Das)
- PassInf-slope: seepage-parallel FoS ≈ 0.5× dry when γ_sat ≈ 2γ_w (γ_sat=19.62)
- PassInf-slope SUBMERGED c'=0: FoS = tanφ/tanβ (= dry, buoyancy) φ=30° β=20°
- PassInf-slope SUBMERGED c'=0: FoS = tanφ/tanβ (= dry, buoyancy) φ=34° β=26°
- PassInf-slope regime ordering: dry > seepage-parallel > rapid-drawdown (c′=0)
- PassInf-slope seepage-parallel: u = γ_w·z·cos²β (u = γ_w·h_p)
- PassInf-slope r_u override: u = r_u·γ·z (r_u=0.1)
- PassInf-slope r_u override: u = r_u·γ·z (r_u=0.25)
- PassInf-slope r_u override: u = r_u·γ·z (r_u=0.5)
- PassInf-slope r_u: FoS decreases monotonically as r_u rises
- PassInf-slope cohesive seepage worked example → FoS ≈ 1.031 (Craig/Das closed form)
- PassBishop search DRY c'≈0: FoS → tanφ/tanβ φ=30° β=18.43° (Skempton-DeLory 1957)
- PassBishop search DRY c'≈0: FoS → tanφ/tanβ φ=35° β=21.8° (Skempton-DeLory 1957)
- PassBishop search DRY c'≈0: FoS → tanφ/tanβ φ=32° β=26.57° (Skempton-DeLory 1957)
- PassBishop search DRY c'≈0: FoS → tanφ/tanβ φ=38° β=18.43° (Skempton-DeLory 1957)
- PassBishop search φ=0 vs Taylor Ns β=60° (Ns=0.191): F=c/(γHNs)
- PassBishop search φ=0 vs Taylor Ns β=53.13° (Ns=0.182): F=c/(γHNs)
- PassBishop dry search == closed-form infinite-slope FoS at the cohesionless limit
- PassBishop on a large-radius circle → closed-form tanφ/tanβ (explicit circle)
- PassBishop: seepage-parallel FoS < dry FoS, and reduction is reported > 0
- PassBishop: FoS decreases monotonically as the phreatic surface rises
- PassBishop: increasing r_u monotonically lowers FoS (u = r_u·γ·z)
- PassBishop slices: u = γ_w·h_p on every slice; max u>0 wet, =0 dry
- PassEngine returns a finite closed-form infinite-slope cross-check
- PassGuard: c′=0 AND φ′=0 is rejected with an error (no shear strength)
- PassGuard: non-positive height is rejected with an error
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-reinforcement-web-validationReinforcement forces in the slope engine (slope-reinforcement.ts): soil nails, rock bolts / anchors, geosynthetics, micropiles.9 passing
Analyses validated: micropile, slope-stability
- Pass[FHWA] planar surface, one nail: passive and active closed forms reproduced by Janbu, Spencer, Morgenstern–Price (static and pseudo-static)
- Pass[FHWA] Sarma on the same planar surface (2 wedges, interfaces normal to the base): passive 2.6917 and active 3.5526 as the closed forms
- Passcapacities at the crossing: tensile, pull-out beyond the surface, facing + bond in front; the least governs and says so
- Passanchor: active by default, free length is not bonded, lock-off load limits the force
- Passgeosynthetic: horizontal force, pull-out from 2·σ′v·tanδ·C per metre embedded when no bond is given (FHWA GEC 11)
- Passorientation: along the element (nail), tangent to the surface (micropile), horizontal (geosynthetic); components resolved as stated
- Passrefusals and warnings by name
- Pass[Y54] Yamagami slope: no pile 1.102 (Slide) / 1.10; the 10.7 kN micropile lifts the same critical circle to 1.193 / 1.20
- Pass[A47] Amherst nailed wall: critical planar surface, two passive nails — 0.890 (Slide, Janbu), 0.887 (Sheahan)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-sarma-web-validationSarma (1979) non-vertical wedges and the global non-circular searches (particle swarm, cuckoo) on the slope engine.10 passing
Analyses validated: slope-stability
- Pass[R4] Hoek spoil pile, drained: Sarma 1.198 (Slide) / 1.2 (Hoek 1987) — optimised interface angle
- Pass[R7] Matthews et al. circle, centre (39.88, 33.63): Sarma 1.175 (Slide), reference 1.136
- Pass[S8] ACADS 3(b) prescribed surface: Sarma against Spencer 1.277, GLE 1.262, Janbu corrected 1.294 and the Giam & Donald reference 1.34
- Pass[S22] F&K composite circle (resampled to 12 wedges): Sarma within 6 % of Spencer / M-P dry (1.382/1.373, 1.372/1.370) and within 6 % with ru 0.25 (1.124/1.118)
- PassSarma with noncircular_search finds a surface, reports the optimiser and the Spencer cross-check; refusals are explicit
- Passpso: Spencer search reproduces Slide #14 1.386, #16 1.094, #7 1.246 within 2 % and never exceeds the pattern search
- Passpso: Janbu simplified search vs Slide #14 1.253 and #16 0.968 (within 2 %), deterministic
- Passcuckoo: Spencer search reproduces Slide #14 1.386, #16 1.094, #7 1.246 within 2 % and never exceeds the pattern search
- Passcuckoo: Janbu simplified search vs Slide #14 1.253 and #16 0.968 (within 2 %), deterministic
- Passthe default optimiser is untouched: omitting noncircular_optimizer equals 'pattern' to the last digit
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-stability-craig-ex122-web-validationCircular method-of-slices slope stability — validated against a PUBLISHED WORKED EXAMPLE on the published circle.8 passing
Analyses validated: slope-stability
- Pass[1-2] the published geometry is self-consistent: the circle passes through the toe
- Pass[3-5] Craig Eq 12.19 reproduced from his own Table 12.1 sums
- Pass[6-8] the engine on the published circle reproduces the published factors of safety
- Pass[9] the RATIO — the anchor that geometry error cannot hide behind
- Pass[10-11] the published finding survives in the engine, not just in the arithmetic
- Pass[12-15] a prescribed circle is used VERBATIM — no search, no substitution
- Pass[16-17] the SEARCH finds something at least as critical as the published circle
- Pass[18-20] omitting trial_circle changes nothing — the search path is untouched
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-stability-geometry-web-validationslope-stability — POLYLINE GEOMETRY validation (stage A: ground_profile, layer bottom_profile, piezometric_line, rigid_base_y_m).16 passing
Analyses validated: slope-stability
- Pass[S3] the printed critical circle meets the read-off ground exactly at the printed endpoints
- Pass[S3] ACADS 1(c) on the printed circle: Bishop 1.405, Spencer 1.375, GLE 1.374
- Pass[S4] ACADS 1(d) kh = 0.15 on the printed circles: Bishop 1.016, Spencer 0.991, GLE 0.989
- Pass[S4] the pseudo-static force acts at the slice CENTROID (Kramer 1996 §10.6.1.1; FHWA GEC-3 §6.2.2)
- Pass[S3] ACADS 1(c) grid search with the rigid base 5 m below the toe: Bishop 1.405, Spencer 1.375
- Pass[S3] the grid search honours the rigid base — no critical circle dips below y = −5
- Pass[S4] ACADS 1(d) grid search: Bishop 1.016, Spencer 0.991
- Pass[S16] Arai & Tagyo Ex 3 with its printed polyline water table: Bishop 1.118, Spencer 1.118
- Pass[S16] u is γw × the vertical distance to the line, clamped to the ground
- Pass[EM] EM 1110-2-1902 F-5 end-of-construction: Simplified Bishop 1.33 on the prescribed circle
- Pass[EM] slices crossing EL 0 weigh both soils; the base soil sets the strength
- Pass[compat] F&K dry prescribed circle (Bishop 2.080 F&K / 2.079 Slide): same result with an equivalent ground_profile
- Pass[compat] ACADS 1(a) grid search (Bishop 0.987 Slide): same result with an equivalent ground_profile
- Pass[compat] polyline-layer mode with ONE soil split in two reproduces the band result
- Passcircle crossing a polyline 4 times: the slip mass is the span containing the lowest point
- Passmalformed / inconsistent geometry is refused with a clear error
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-stability-noncircular-search-web-validationrecords a differenceslope-stability — SEARCH for the critical non-circular surface (`noncircular_search`), 2026-10-03.6 passing
Analyses validated: slope-stability
- Pass[S14] Arai & Tagyo Ex 1 Janbu search: simplified 1.253 (Slide) / 1.265 (A&T), corrected 1.346 / 1.357
- Pass[S14] Arai & Tagyo Ex 1 Spencer search: 1.386 (Slide), below the best circle
- Pass[S16] Arai & Tagyo Ex 3 Janbu search: simplified 0.968 / 0.995, corrected 1.050 / 1.071
- Pass[S16] Arai & Tagyo Ex 3 Spencer search: 1.094 (Slide)
- Pass[S7] ACADS 3(a) weak seam: Spencer 1.246 (Slide), inside the Giam & Donald reference range 1.24 – 1.27
- Passthe search is deterministic and refuses methods defined only for circles
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-stability-noncircular-web-validationslope-stability — NON-CIRCULAR slip surfaces (stage C): General Limit Equilibrium (Fredlund & Krahn 1977) Spencer and Morgenstern-Price, Janbu simplified and Janbu (1973) corrected, on a prescribed polyline `slip_surface`.10 passing
Analyses validated: slope-stability
- Pass[S8] ACADS 3(b) prescribed non-circular surface: Spencer 1.277, GLE 1.262, Janbu corrected 1.294
- Pass[S8] slices break at the seam crossing: no base straddles two materials
- Pass[S22] F&K composite circle, dry: Spencer 1.382 (Slide) / 1.373 (F&K), M-P 1.372 / 1.37
- Pass[S22] F&K composite circle, ru 0.25: Spencer 1.124 (Slide) / 1.118 (F&K), M-P 1.114 / 1.118
- PassGLE(f = 1) = circular Spencer on the F&K circle, dry
- PassGLE(f = 1) = circular Spencer on the F&K circle, ru 0.25
- PassGLE(f = 1) = circular Spencer on the F&K circle, k_h 0.15
- PassGLE(f = 1) = circular Spencer on the F&K circle, water-filled 3 m crack
- Passa slip_surface that traces the F&K circle reproduces the prescribed-circle result
- Passslip_surface refusals are explicit
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-stability-strip-load-web-validationslope-stability — STRIP LOADS (offset surcharge), 2026-10-03.8 passing
Analyses validated: slope-stability
- Pass[MKB Table 1] β = 30°: Spencer 1.36, Bishop 1.37 (SLIDE 6.0)
- Pass[MKB Table 1] β = 45°: Spencer 1, Bishop 1.01 (SLIDE 6.0)
- Pass[MKB Table 1] β = 60°: Spencer 0.79, Bishop 0.8 (SLIDE 6.0)
- Pass[MKB Table 3] example 2: Spencer 0.7 (SLIDE 6.0), inside the FELA bracket 0.69–0.71
- Passa strip load covering the whole crest region equals the existing crest surcharge
- Passphysics: FoS falls with load magnitude and recovers with setback (MKB §3.2–3.3 trends)
- Passlinearly varying pressure is integrated exactly (trapezoid force and centroid)
- Passrefusals: reversed span, negative pressure, non-finite values
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-stability-tension-crack-web-validationslope-stability — TENSION CRACK (stage B) and the JANBU SIMPLIFIED kernel.8 passing
Analyses validated: slope-stability
- Pass[S2] ACADS 1(b) on the printed circle: Bishop 1.596, Spencer 1.592, GLE 1.592
- Pass[S2] ACADS 1(b) grid search: Bishop 1.596, Spencer 1.592
- Pass[S2] the crack truncates the slip at depth_m and the water thrust is ½γw·hw² at hw/3
- PassCraig 8e p. 474 — φ = 0 with a water-filled crack: the engine equals the moment equation
- Pass[S56] Pockoski & Duncan slope 2 on the printed circle: Spencer 1.290, Bishop 1.285; endpoints as printed
- Pass[S56] grid search: Bishop 1.285, Spencer 1.290, Janbu simplified 1.141
- Pass[S16] Arai & Tagyo circular: Janbu simplified 1.046 (Slide Table 16.2)
- Passinvalid tension-crack input is refused with a clear error
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-stability-web-validationWEB-BENCHMARK validation for the circular method-of-slices slope engine (the release rules ≥20 cited-value gate).26 passing
Analyses validated: slope-stability
- PassSlope web: c=0 FoS=tanφ/tanβ φ=25° 2:1 (β=26.6°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=25° 2.5:1 (β=21.8°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=25° 3:1 (β=18.4°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=25° 4:1 (β=14.0°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=30° 2:1 (β=26.6°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=30° 2.5:1 (β=21.8°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=30° 3:1 (β=18.4°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=30° 4:1 (β=14.0°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=35° 2:1 (β=26.6°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=35° 2.5:1 (β=21.8°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=35° 3:1 (β=18.4°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=35° 4:1 (β=14.0°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=40° 2:1 (β=26.6°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=40° 2.5:1 (β=21.8°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=40° 3:1 (β=18.4°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=40° 4:1 (β=14.0°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=45° 2:1 (β=26.6°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=45° 2.5:1 (β=21.8°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=45° 3:1 (β=18.4°)
- PassSlope web: c=0 FoS=tanφ/tanβ φ=45° 4:1 (β=14.0°)
- PassSlope web: φ=0 undrained vs Taylor Ns β=60° (Ns=0.191)
- PassSlope web: φ=0 undrained vs Taylor Ns β=53.13° (Ns=0.182)
- PassSlope E-113: an INVERTED layer must be rejected, not silently read as the deepest layer
- PassSlope E-113: layer elevations ARE honoured — order of strata changes FoS
- PassSlope E-113: a gap or overlap in the profile must be reported
- PassSlope E-113: non-finite and non-physical layer properties must be rejected
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-stability-worked-examples-web-validationslope-stability — FULL WORKED EXAMPLES (the ≥20-value gate).15 passing
Analyses validated: slope-stability
- Pass[FK] dry: Ordinary 1.928 / 1.931 (F&K / Slide)
- Pass[FK] dry: Bishop 2.080 / 2.079 — read from `critical.fos`, which must now BE Bishop
- Pass[FK] dry: Spencer 2.073 / 2.075
- Pass[FK] dry: Morgenstern-Price 2.076 / 2.075
- Pass[FK] ru 0.25: Ordinary 1.607 (F&K; Slide 1.687 uses a different ru convention)
- Pass[FK] ru 0.25: Bishop 1.766 / 1.763, Spencer 1.761 / 1.760, M-P 1.764 / 1.760
- PassSpencer picks the PHYSICAL root: F&K θ ≈ +14°, and Spencer ≈ Bishop on the same circle
- Pass[AT] Arai & Tagyo Ex 3 (horizontal water-table approximation): Spencer takes the physical root, ≈ Bishop
- PassMorgenstern-Price with f(x) = constant reduces to Spencer
- Pass[SLIDE] HC#1 dry: Bishop 2.113
- Pass[SLIDE] HC#2 water table at surface: Bishop 1.554
- Pass[ACADS] 1(a): Bishop 0.987, Spencer 0.986, M-P 0.986; ACADS reference 1.00
- Pass[ACADS] 1(a): Janbu simplified (uncorrected) 0.939 (SLOPE/W §2.1 Table 2)
- Pass[CRAIG] Ex 12.1: φu = 0, F = 2.48 (graphical area 70 m², d 4.5 m) — and Spencer = Bishop
- Pass[VAR] Ex 24.1: φ = 0 — printed 1.14 uses a graphical area 7.5 % larger than its own geometry
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
taylor-stability-web-validationtaylor-stability — dedicated validation against PUBLISHED worked answers (`taylor-stability.ts`).18 passing
Analyses validated: taylor-stability
- Pass[F] Example 6-1, trial Fc=Fφ=1.6, Ns=0.065: printed H = 40.1 ft
- Pass[F] Example 6-1, trial Fc=Fφ=1.9, Ns=0.073: printed H = 30.04 ft and FS ≈ 1.9
- Pass[F] Example 6-1a table row Fφ=1 (φd=20°, Ns=0.026): printed Fc = 5.3
- Pass[F] Example 6-1a table row Fφ=1.5 (φd=14°, Ns=0.055): printed Fc = 2.5
- Pass[F] Example 6-1a table row Fφ=2 (φd=10°, Ns=0.075): printed Fc = 1.9
- Pass[F] Example 6-1a table row Fφ=2.5 (φd=8°, Ns=0.087): printed Fc = 1.6
- Pass[K] Craig Ex. 12.1(a): Ns = 0.18 → F = 2.37
- Pass[K] Craig Ex. 12.1(c): EC7 DA1b design cu = 65/1.40 → maximum cutting depth h ≤ 13.58 m
- Pass[V] Example 24.1 (Terzaghi Ns_T = 5.52, c = 25 kPa, γ = 19): H_c = 7.26 m, FoS(H = 6 m) = 1.21
- Pass[V] Example 24.3 (Ns_T = 7.8, c = 30, γ = 20, H = 8): F.S. against cohesion = 1.46
- Pass[V] Example 24.4 (Ns_T = 6.8, γ = 20, H = 8): required c = 23.5 kN/m², FoS on available c = 30 → 1.28
- Pass[V] Example 24.5 (γH_c/c = 7.2, c = 12, γ = 19 as used in the solution): H_c = 4.55 m, H(FS=1.5) = 3.03 m
- Pass[U] Example E-1 (N0 = 5.8, c = 452 psf, Pd = 2302 psf): F = 1.14
- Pass[U] Example E-2 (N0 = 5.6, c = 499 psf, Pd = 2253 psf): F = 1.24
- Pass[U] Example E-3 (Ncf = 6, c = 735 psf, Pd = 4500 psf): F = 1.0
- Pass[U] Example E-4 (Ncf = 35, c = 134 psf, Pd = 4141 psf): F = 1.13
- Passdefinition checks: c_d = Ns·γ·H, and FoS = 1 exactly at H = H_c
- Passzero / negative / non-numeric Ns, γ or H are refused (no fabricated FoS)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Retaining walls, excavations and structural elements
46 finite-element rows (5 deviations, 2 recorded, 3 superseded) · 3 closed-form problems · 35 validation suites
Finite-element solver registry
Showing 46 of 46 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
total discharge under the dam (impermeable wall, confined flow) plaxis-verif-confined-wall-Q | 0.81959m³/day/m | 0.82m³/day/m | −0.05 % | Ours 0.81959 m³/day/mPublished 0.82 m³/day/m−0.05 % | Pass | |
| ||||||
midspan deflection, point load F = 100 kN/m, L = 1 m, EA 1e5, EI 83.33, ν 0 (simply supported) plaxis-verif-bending-plates-point-u | 25.6mm | 25.6mm | 0.00 % | Ours 25.6 mmPublished 25.6 mm0.00 % | Pass | |
| ||||||
Mmax, point load plaxis-verif-bending-plates-point-M | 25kNm/m | 25kNm/m | 0.00 % | Ours 25 kNm/mPublished 25 kNm/m0.00 % | Pass | |
| ||||||
Qmax, point load plaxis-verif-bending-plates-point-Q | 50kN/m | 50kN/m | 0.00 % | Ours 50 kN/mPublished 50 kN/m0.00 % | Pass | |
| ||||||
midspan deflection, distributed load q = 200 kN/m/m plaxis-verif-bending-plates-dist-u | 31.85mm | 31.85mm | 0.00 % | Ours 31.85 mmPublished 31.85 mm0.00 % | Pass | |
| ||||||
Mmax, distributed load plaxis-verif-bending-plates-dist-M | 25kNm/m | 25kNm/m | 0.00 % | Ours 25 kNm/mPublished 25 kNm/m0.00 % | Pass | |
| ||||||
Qmax, distributed load plaxis-verif-bending-plates-dist-Q | 100kN/m | 100kN/m | 0.00 % | Ours 100 kN/mPublished 100 kN/m0.00 % | Pass | |
| ||||||
sliding force at failure (plateau), push 1 mm plaxis-verif-sliding-block-force | 60.0763kN/m | 60.076kN/m | 0.00 % | Ours 60.0763 kN/mPublished 60.076 kN/m0.00 % | Pass | |
| ||||||
average maximum shear stress under the block plaxis-verif-sliding-block-avg-tau | 15.0191kPa | 15.019kPa | +1.0e-3 % | Ours 15.0191 kPaPublished 15.019 kPa+1.0e-3 % | Pass | |
| ||||||
lateral load P at u = 0.08 m (1.6 % of D), strict convergence plaxis-verif-pipe-capacity-r1.0 | 299.87kN/m | 298.5kN/m | +0.46 % | Ours 299.87 kN/mPublished 298.5 kN/m+0.46 % | Pass | |
| ||||||
lateral load P at u = 0.08 m (1.6 % of D), strict convergence plaxis-verif-pipe-capacity-r0.8 | 290.51kN/m | 289.1kN/m | +0.50 % | Ours 290.51 kN/mPublished 289.1 kN/m+0.50 % | Pass | |
| ||||||
lateral load P at u = 0.08 m (1.6 % of D), strict convergence plaxis-verif-pipe-capacity-r0.6 | 279.1kN/m | 277.2kN/m | +0.68 % | Ours 279.1 kN/mPublished 277.2 kN/m+0.68 % | Pass | |
| ||||||
lateral load P at u = 0.08 m (1.6 % of D), strict convergence plaxis-verif-pipe-capacity-r0.4 | 265.56kN/m | 263.3kN/m | +0.87 % | Ours 265.56 kN/mPublished 263.3 kN/m+0.87 % | Pass | |
| ||||||
lateral load P at u = 0.08 m (1.6 % of D), strict convergence plaxis-verif-pipe-capacity-r0.2 | 249.61kN/m | 247.1kN/m | +1.00 % | Ours 249.61 kN/mPublished 247.1 kN/m+1.00 % | Pass | |
| ||||||
initial horizontal stiffness Kxx of the full pipe, R_inter = 1 plaxis-verif-pipe-initial-stiffness | 99102kN/m | 99125kN/m | −0.02 % | Ours 99102 kN/mPublished 99125 kN/m−0.02 % | Pass | |
| ||||||
maximum bending moment in the wall, final excavation (−6 m), characteristic parameters, embedment 4 m ertc7-wall-moment | 204kNm/m | 212kNm/m | −3.77 % | Ours 204 kNm/mPublished 212 kNm/m−3.77 % | Deviation | |
| ||||||
strut force, final excavation ertc7-strut-force | 123.9kN/m | 117kN/m | +5.90 % | Ours 123.9 kN/mPublished 117 kN/m+5.90 % | Deviation | |
| ||||||
horizontal displacement of the wall base, final excavation ertc7-wall-base-displacement | 9mm | 6mm | +50.0 % | Ours 9 mmPublished 6 mm+50.0 % | Deviation | |
| ||||||
|u| at (50, 10) at the end of each phase (submerged excavation, undrained-A clay) plaxis-2d-tut3 | phase1: 0.0092; phase2: 0.0302; phase3: 0.0302; phase4: 0.074; phase5: stops at ΣMstage 0.350 (tol 1e-8 and 1e-7); at t… | phase1: 0.005; phase2: 0.024; phase3: 0.024; phase4: 0.057; phase5: 0.141 | — | Ours phase1: 0.0092; phase2: 0.0302; phase3: … mPublished phase1: 0.005; phase2: 0.024; phase3: 0.… m— | Superseded | |
| ||||||
cantilever tip deflection, tip load P = 10, L = 2, EI 1e3, EA 2e5, ν 0.2 (plane strain: EI/(1−ν²)) k3-gate-cantilever | 0.025888m | 0.025888m | 0.00 % | Ours 0.025888 mPublished 0.025888 m0.00 % | Pass | |
| ||||||
moment over the middle support, two equal spans L = 2 under q = 12 k3-gate-two-span | 5.93325kNm/m | 5.93325kNm/m | 0.00 % | Ours 5.93325 kNm/mPublished 5.93325 kNm/m0.00 % | Pass | |
| ||||||
centre deflection of a simply supported circular plate (axisymmetric), a = 2, q = 10, ν 0.3 k3-gate-circular-plate | 0.009301m | 0.009301m | 0.00 % | Ours 0.009301 mPublished 0.009301 m0.00 % | Pass | |
| ||||||
collapse load of a simply supported Mp-plate (N–M diamond), with and without N = 100 (Np 400) k3-gate-plastic-hinge · Self-check | —kN/m | —kN/m | 0.00 % | Ours — kN/mPublished — kN/m0.00 % | Pass | |
| ||||||
node-to-node / fixed-end anchor displacement and force k3-gate-anchor-spring | 0.2m | 0.2m | 0.00 % | Ours 0.2 mPublished 0.2 m0.00 % | Pass | |
| ||||||
tension-only geogrid: u = F L / EA in tension; zero force in compression k3-gate-geogrid | 0.08m | 0.08m | 0.00 % | Ours 0.08 mPublished 0.08 m0.00 % | Pass | |
| ||||||
sliding resultant Σ τ = R (c L + tan φ N) and every point on the Coulomb line, R_inter 1 and 0.6 k3-gate-interface-patch | 36.0458kN/m | 36.0458kN/m | 0.00 % | Ours 36.0458 kN/mPublished 36.0458 kN/m0.00 % | Pass | |
| ||||||
heave of the new surface after removing 3 m of a laterally restrained elastic column (7 m remain) k3-gate-excavation-unloading | 0.0315m | 0.0315m | 0.00 % | Ours 0.0315 mPublished 0.0315 m0.00 % | Pass | |
| ||||||
settlement of a very stiff plate loaded by the force of a rough rigid footing pushed δ = 0.01 k3-gate-plate-soil-compatibility · Self-check | 0.0100001m | 0.01m | +1.0e-3 % | Ours 0.0100001 mPublished 0.01 m+1.0e-3 % | Pass | |
| ||||||
global equilibrium every phase of a staged excavation (wall plate, two-sided interface, prestressed strut, two stages): ΣRy = soil weight + wall weight, ΣRx = −strut k3-gate-staged-wall-equilibrium · Self-check | —kN/m | —kN/m | 0.00 % | Ours — kN/mPublished — kN/m0.00 % | Pass | |
| ||||||
top anchor force at the end of phase 3 (prestress 500 kN per anchor, Lspacing 2.5 m) plaxis-2d-tut7-prestress-top | 500kN | 500kN | 0.00 % | Ours 500 kNPublished 500 kN0.00 % | Pass | |
| ||||||
bottom anchor force at the end of phase 5 (prestress 1000 kN) plaxis-2d-tut7-prestress-bottom | 1000kN | 1000kN | 0.00 % | Ours 1000 kNPublished 1000 kN0.00 % | Pass | |
| ||||||
final phase: wall max |M|, anchor forces, wall displacements plaxis-2d-tut7-final | wallL Mmax: 154; wallR Mmax: 157; at y: 23; anchors top L/R: [430.4, 428.6]; anchors bottom L/R: [1053.4, 1050.8]; ux(4… | — | — | Ours wallL Mmax: 154; wallR Mmax: 157; at y: …Published —— | Superseded | |
| ||||||
final phase with REAL phase-6 steady flow: wall max |M|, anchor forces, wall displacements plaxis-2d-tut7-final-k4-flow | wallL Mmax: 167; wallR Mmax: 170.7; at y: 23; anchors top L/R: [420.1, 424.4]; anchors bottom L/R: [1081.6, 1081.8]; ux… | — | — | Ours wallL Mmax: 167; wallR Mmax: 170.7; at y…Published —— | Superseded | |
| ||||||
Tutorial 7 with the REAL Hardening Soil (Table 7-1) + phase-6 steady flow: anchor forces, wall max |M|, wall ux k5b-plaxis-2d-tut7-real-hs | prestress P3 / P5: [500, 1000]; final anchors top L/R: [450.6, 446.8]; final anchors bottom L/R: [1058.8, 1055.4]; wall… | prestress 500 / 1000 kN (figures otherwise) | — | Ours prestress P3 / P5: [500, 1000]; final an…Published prestress 500 / 1000 kN (figures otherwi…— | Recorded, no published value | |
| ||||||
|u| at (50, 10) at the end of each phase — real Hardening Soil, the kernel's own submerged excavation (D90: deactivated clusters keep their water) k5d-plaxis-2d-tut3-submerged-hs | phase1: 0.0054; phase2: 0.0225; phase3: 0.0225; phase4: 0.0589; phase5: 0.1519 | phase1: 0.0062; phase2: 0.0242; phase3: 0.0242; phase4: 0.0572; phase5: 0.1417 | phase1: -12.9; phase2: -7; phase3: -7; phase4: 3; phase5: 7.2 % | Ours phase1: 0.0054; phase2: 0.0225; phase3: … mPublished phase1: 0.0062; phase2: 0.0242; phase3: … mphase1: -12.9; phase2: -7; phase3: -7; p… | Deviation | |
| ||||||
Tutorial 10: Tutorial 7 (real HS) + two extraction wells in the phase-6 steady flow (1.5 m³/day/m, h_min 17 m): well discharges, groundwater head in the pit, final anchor forces / wall moments k5d-plaxis-2d-tut10-dewatering | well discharge each (m³/day/m): -0.9797; side inflow each: 0.9773; pit-bottom seepage: 0; head in the pit (m): 18.90–18… | figures only (head lowered in the excavation, flow to the wells) | — | Ours well discharge each (m³/day/m): -0.9797;…Published figures only (head lowered in the excava…— | Recorded, no published value | |
| ||||||
design-approach presets DA1-1 (A1+M1), DA1-2 (A2+M2), DA2 (A1+M1), DA3 (A2+M2 on geotechnical actions): γG 1.35/1.0, γQ 1.5/1.3, γφ′ = γc′ 1.25, γcu 1.4, γqu 1.4, γγ 1.0; tan φ factored, ψ ≤ φ_d k5d1-da-ec7-annex-a | 1.25 | 1.25 | 0.00 % | Ours 1.25Published 1.250.00 % | Pass | |
| ||||||
worst bar-point axial-force error (of N(0) = 48.2014 kN/m) of a pulled grouted cable with an elastic bond Ks k5d1-cable-winkler · Self-check | 2.050e-5 | 0.002 | — | Ours 2.050e-5Published 0.002— | Pass | |
| ||||||
worst error of the pulled-cable force against the plastic bond capacity (c_bond + σn tan φ_bond P)·L / L_spacing = 15 kN/m k5d1-cable-plastic-bond · Self-check | 8.890e-11 | 1.000e-6 | — | Ours 8.890e-11Published 1.000e-6— | Pass | |
| ||||||
worst bar-point axial-force error of an embedded beam row (skin spring R_s + tension-free base spring K_F), push and pull k5d1-embedded-beam-axial · Self-check | 3.280e-6 | 0.001 | — | Ours 3.280e-6Published 0.001— | Pass | |
| ||||||
worst bending-moment error (of the maximum 1.4963 kNm/m) of a laterally loaded embedded beam row (λL = 8.34) k5d1-embedded-beam-lateral · Self-check | 0.00713 | 0.02 | — | Ours 0.00713Published 0.02— | Pass | |
| ||||||
β-method (deconfinement d = 0.6) wall displacement of an elastic circular opening, then the lined state k5d1-beta-method-cc | 0.00750509m | 0.0075m | +0.07 % | Ours 0.00750509 mPublished 0.0075 m+0.07 % | Pass | |
| ||||||
ΣMsf of the Safety phase on SLS phase 6 k5d1-plaxis-2d-tut8-safety-sls | 1.4828 | 1.49 | −0.48 % | Ours 1.4828Published 1.49−0.48 % | Pass | |
| ||||||
ΣMsf of the Safety phase on ULS phase 12 (DA3: inherits the design strengths) k5d1-plaxis-2d-tut8-safety-uls | 1.1813 | 1.19 | −0.73 % | Ours 1.1813Published 1.19−0.73 % | Pass | |
| ||||||
|u| at (40, 27) at the end of ULS phase 12 (real Hardening Soil, DA3) k5d1-plaxis-2d-tut8-uls-displacement | 0.069m | 0.0518m | +33.2 % | Ours 0.069 mPublished 0.0518 m+33.2 % | Deviation | |
| ||||||
meshed area of a square cut by two crossing structure lines that close a face against the boundary k5d1-mesher-crossing-structures · Self-check | 100m² | 100m² | 0.00 % | Ours 100 m²Published 100 m²0.00 % | Pass | |
| ||||||
Closed-form engine registry
| Problem | Ours | Published | Difference | Tolerance | Status | Details | |
|---|---|---|---|---|---|---|---|
Steel strut flexural buckling — Designers’ Guide EC3 Ex. 6.7, N_b,Rd DC-STRUT-DGEC3-6.7 | 2296.79kN | 2297kN | −9.2e-3 % | ± 0.1 % | Ours 2296.79 kNPublished 2297 kN−9.2e-3 % | Pass | |
| |||||||
Geogrid long-term design strength — GEC-11 Vol II Ex. E1 Table E1-7.3, GG-I, T_r = φ·T_al·R_c DC-GEOGRID-GEC11-E1-GG1 | 976.227lb/ft | 976lb/ft | +0.02 % | ± 0.1 % | Ours 976.227 lb/ftPublished 976 lb/ft+0.02 % | Pass | |
| |||||||
Ground anchor grout–ground bond — GEC-4 Appendix A Example 1, allowable bond at L = 12 m DC-ANCHOR-GEC4-EX1-BOND | 600kN | 600kN | 0.00 % | ± 0.5 % | Ours 600 kNPublished 600 kN0.00 % | Pass | |
| |||||||
Cited validation suites
as4678-factors-web-validationAS 4678—2002 partial-factor system — anchored to the standard.12 passing
Analyses validated: not attributed by the manifest
- PassAS 4678 Table 1.1: C is the MOST critical class and A the LEAST — the reverse of EC8/ASCE
- PassAS 4678 Table 5.2: Φn = 0.9 (C), 1.0 (B), 1.1 (A) at ULS; all 1.0 at SLS
- PassAS 4678: choosing class A emits the caution, because the letter reads like the opposite
- PassAS 4678 Table 5.1(A): every published Φuφ and Φuc reproduced (16 values)
- PassAS 4678 Table 5.1(A) internal ordering: better fill ⇒ higher factor, SLS ≥ ULS
- PassAS 4678 Table 5.1(B): Φuφ = 0.0 in EVERY column — undrained credits no friction
- PassAS 4678 §5.2: an undrained analysis returns φ* = 0 and factors cu only
- PassAS 4678 §5.2.1 and §5.2.2: c* = Φuc·c and tan φ* = Φuφ·tan φ
- PassAS 4678 vs EN 1997-1: the conventions are RECIPROCAL, and that is asserted
- PassAS 4678 Table 4.1: minimum live loads 1.5 / 2.5 (class A) and 2.5 / 5 (classes B, C)
- Passthe design soil is never non-finite, negative or stronger than characteristic
- Passthe citations name the standard, its amendments and the companion AS 1170 parts
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
basal-heave-web-validationrecords a differenceBASAL-HEAVE — web-validation benchmark against published worked examples and tables.7 passing
Analyses validated: basal-heave
- PassNAVFAC DM-7.2 Fig. 30 — strip and rectangular Nc at H/B = 1.67, B/L = 0.15
- PassNAVFAC DM-7.2 Fig. 30 — driving and resisting pressure, factor of safety, verdict
- PassBowles 5e Table 14-1 (p. 813) — strip N′c at D/B = 0, 4.0 and 5.0
- PassBowles 5e Table 14-1 (p. 813) — square/circular N′c (Skempton column) at D/B = 0, 4.0 and 5.0
- PassVarghese Ex. 22.1 (p. 417) — Skempton Nc, bearing capacity, overburden, FS
- PassDas 8e Eq. 15.16 / Craig §11.9 — Terzaghi branch constants: Nc = 5.7 and B′ ≈ 0.7B
- PassDas §15.7 (p. 800) and NAVFAC Table 6 — the recommended base-heave factor of safety is 1.5
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
braced-excavation-web-validationrecords a difference`braced-excavation` — anchored to NAVFAC DM-7.02 Figures 26 and 27.11 passing
Analyses validated: braced-excavation
- PassNAVFAC Fig. 26(a): sand σh = 0.65·KA·γH with KA = tan²(45 − φ/2)
- PassNAVFAC Fig. 26(b): σh = γH − 4·m·c, and N₀ = γH/c is the selection basis
- PassE-48: m = 0.4 where the cut is underlain by deep soft NC clay — a 1.48× increase
- PassNAVFAC Fig. 26(c): stiff clay σh spans 0.2·γH to 0.4·γH, selectable
- PassE-49: a ratio outside Figure 26(c)’s 0.2–0.4 band is flagged as unsupported
- PassNAVFAC Fig. 26(c): for 4 < N₀ < 6 the LARGER of diagrams (b) and (c) is used
- PassNAVFAC Figs. 26 & 27: strut forces from hinges at strut locations / simple span between braces
- Passstrut spacing converts kN/m to kN per strut linearly
- PassNAVFAC Fig. 26 note: the bottom-instability FoS band is 1 ≤ FSB ≤ 1.5
- Passthe governing figures are cited, and the OCR-ambiguous value is NOT asserted anywhere
- Passevery numeric output is finite, and a cut with no struts is refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
building-damage-assessment-web-validationrecords a differenceDedicated validation for the building-damage engine (`building-damage-assessment.ts`): the Burland & Wroth (1974) equivalent-beam deflection-ratio + horizontal-strain method with Boscardin & Cording (1989) damage categories, as codified by…10 passing
Analyses validated: building-damage-assessment
- PassBoscardin & Cording (1989) Table 2: damage category vs limiting tensile strain
- PassRankin (1988): settlement < 10 mm and slope < 1/500 → screened out, category 0
- PassRankin screen does NOT apply above 10 mm
- PassSagging beam: Δ/L → εb, εd, εbt, εdt reproduce M-T-B (1996) eqs 7-10 exactly
- PassHogging beam: a building offset past the inflection point hogs (I = H³/3, t = H)
- PassE/G = 12.5 framed RC raises the shear stiffness and lowers the diagonal strain (M-T-B §4.5)
- PassL/H regime warning: diagonal dominates for L/H < 1.5, bending for L/H > 1.5
- PassBuilding length capped at 2.5i (M-T-B 1996 §4.1)
- PassCording et al. (2008) Evanston South Wing: angular distortion 2.7e-3, lateral strain 2.5e-3
- PassInput validation: L, H, i, profile errors
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
concrete-durability-web-validationrecords a differenceDedicated validation for the concrete durability classification (`concrete-durability.ts`): the IS 456:2000 Table 4 sulphate exposure class from soil SO3 (%) and groundwater SO4 (g/L), the cement type, minimum cement content and maximum fr…9 passing
Analyses validated: concrete-durability
- PassIS 456:2000 Table 4: sulphate class from total SO3 in soil (% by mass), interior of each printed band
- PassIS 456:2000 Table 4: sulphate class from SO4 in groundwater (g/L), interior of each printed band
- PassIS 456:2000 Table 4: the printed open/closed ends of the bands
- PassIS 456:2000 Table 4: minimum cement content (kg/m³) per class
- PassIS 456:2000 Table 4: maximum free water-cement ratio per class
- PassIS 456:2000 Table 4 class 3: Portland pozzolana / slag cement have their own, stricter row (350 kg/m³, w/c 0.45)
- PassIS 456:2000 Table 16 and cl 26.4.2.2: cover is max(50 mm footing floor, Table 16) for every class
- PassIS 456:2000 Table 16: Extreme exposure 75 mm; Very severe is 50 mm (not more) for a footing
- PassIS 456:2000 cl 8.2.2.4 / Table 4 Note 3: pH scope warnings
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
contiguous-pile-wall-web-validationWeb-benchmark validation for `contiguous-pile-wall`.12 passing
Analyses validated: contiguous-pile-wall
- Passthe active pressure at the dredge line is Rankine Ka·σv, with the surcharge included
- PassRankine Ka and Kp are reciprocal, and cohesion relieves the ACTIVE side
- Passwall friction δ reduces the horizontal active thrust (Coulomb, δ = 0 → Rankine)
- Passbelow the water table the engine uses γ′ = γ_sat − γ_w and adds hydrostatic thrust
- Passomitting γ_sat below the water table is flagged rather than assumed silently
- Passthe moment capacity is IS 456 Annex G M_lim = 0.138·f_ck·D·d_eff²
- Passsteel area follows A_st = M_u/(0.87·f_y·0.9·d_eff) with the IS 456 0.4 % floor
- Passper-pile actions scale with the pile spacing (tributary width)
- Passbasal-heave Nc follows Bjerrum & Eide 5.7 + 0.39·(H/B), capped at 9
- Passa low basal-heave FoS fails the wall, and a frictional soil withholds the check
- Passthe deflection estimate sits in the CIRIA C760 §8.1 band 0.001–0.005·H
- Passinvalid inputs are refused with a zeroed result, including the E-9 f_y guard
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
deadman-anchor-web-validationrecords a differenceDEADMAN-ANCHOR — web-validation benchmark against published coefficient tables and a worked example.4 passing
Analyses validated: deadman-anchor
- PassBowles 5e Table 11-3 (p. 603) — Rankine Ka, β = 0, φ = 26°…42°
- PassBowles 5e Table 11-4 (p. 603) — Rankine Kp, β = 0, φ = 26°…42°
- PassDas 8e Table 12.1 (p. 608) — Ka(R) at α = 0°, θ = 0°, φ′ = 28°…40°
- PassBowles 5e Example 13-7 (p. 779) — block-face earth forces (Kp = 3.25, Ka = 0.307 in the book)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
earth-pressure-web-validationWEB-BENCHMARK validation for the lateral earth-pressure engine (the release rules mandatory ≥20 cited-value gate).12 passing
Analyses validated: earth-pressure
- PassEP web 1–10: Rankine Ka at φ=20,25,28,30,32,34,35,36,40,45 (Rankine 1857 / Das)
- PassEP web 11–15: Rankine Kp at φ=20,30,35,40,45 (Rankine 1857 / Das)
- PassEP web 16–18: at-rest K0 = 1−sinφ at φ=30,35,40 (Jaky 1948)
- PassEP web 19–20: Rankine Ka sloping backfill φ=30°, β=10°/20° (Das Eq. 13.x)
- PassEP web 21–22: active thrust Pa=½Ka γ H² (φ=30 H=6; φ=35 H=5)
- PassEP web 23: passive thrust Pp=½Kp γ H² (φ=30 H=5) = 675 kN/m
- PassEP web 24: active resultant at H/3 (φ=30, H=6 → 2.0 m)
- PassEP web 25: Bell tension-crack depth z_c=2c/(γ√Ka) (c=20, φ=20, γ=18 → 3.17 m)
- PassEP E-115: the reference Rankine case is untouched (Ka = 1/3, Pa = 75 kN/m)
- PassEP E-115: wall friction δ — NaN, negative, and δ > φ must all be refused
- PassEP E-115: backfill slope β ≥ φ must be refused, not warned
- PassEP E-115: wall inclination α must be finite and within ±90°
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
earth-pressure-worked-examples-web-validationearth-pressure — FULL WORKED EXAMPLES (the ≥20-value gate).15 passing
Analyses validated: earth-pressure
- Pass[DAS] Ex 12.1: at-rest thrust with the water table at 2.5 m → P0 = 122.85 kN/m at 1.53 m
- Pass[BOW] Ex 11-4: c 10.5, φ 10°, H 6.5 → R = 158.5 kN/m at 1.69 m (tension zone neglected), zc = 1.43 m
- Pass[BOW] Prob 11-7: crack replaced → full-height thrust = 103.3 kN/m at H/3
- Pass[BOW] Prob 11-5: printed 63.2 kN/m is the net area, printed 4.65/3 m is the neglect-zone centroid
- Pass[CRAIG] Ex 11.2(b): water table at 2 m → total thrust 93.3 kN/m
- Pass[DAS] Ex 12.6: Coulomb, φ 35°, δ = ⅔φ, H 5 m, γ 17.6 → Pa = 53.77 kN/m
- Pass[DAS] Ex 12.7: Coulomb, battered back + 95.76 kPa surcharge → total ≈ 328.2 kN/m
- Pass[DAS] Ex 12.11: Mononobe-Okabe, kh 0.3 → P_ae = 46.05 kN/m (static 22.88)
- Pass[DAS] Ex 12.14: passive with wall friction → Caquot-Kérisel 311 kN/m (Coulomb 351.6)
- Pass[DAS] Ex 13.1: Rankine, H 7.158 m, β 10° → Pa = 161.2 kN/m
- Pass[DAS] Ex 13.2: Coulomb, battered back 15°, δ = ⅔φ → Pa = 157.22 kN/m
- Pass[BOW] Ex 11-1: Coulomb, β 10°, δ 20° → Pa = 74.5 kN/m at H/3
- Pass[BOW] Ex 11-3: Rankine, β 10° → Pa = 76.6 kN/m
- Pass[EC7] Dublin A.4.2/A.4.5: Ka;β = 0.365 and the characteristic soil thrust E_a;Gk = 201 kN/m
- Pass[USACE] EM 1110-2-2502 App. H: peak Ka 0.31 and Kp 3.25 at φ 32°
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
eurocode7-factors-web-validationEurocode 7 partial factors — validated against **EN 1997-1:2004 (BS EN 1997-1:2004)**, *Eurocode 7: Geotechnical design — Part 1: General rules*, **Annex A**.9 passing
Analyses validated: not attributed by the manifest
- PassEN 1997-1 Cl 2.4.7.3.4 — every Design Approach combines the correct A/M/R sets
- PassTable A.4 — γφ′ is applied to tan φ′, not to φ′ (via the engine's own ec7ReduceMaterials)
- PassEN 1997-1 Cl 2.4.7.3.1 eq 2.6a/b — Fd = γG·Gk + γQ·Qk via ec7DesignAction
- Passthe three EC7 verification philosophies are structurally distinct
- Passevery factor is ≥ 1 and finite — a partial factor can never increase capacity
- PassEC7_LABELS name the A/M/R combination so a report shows which philosophy was used
- PassNational Annex variations are DOCUMENTED and deliberately NOT auto-applied
- PassDA3 exposes the A1 (structural) action set, and says so
- Passthe four approaches produce four DIFFERENT design outcomes (they are not aliases)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
excavation-settlement-web-validationrecords a differenceEXCAVATION-SETTLEMENT — web-validation benchmark against published envelopes and limits.11 passing
Analyses validated: excavation-settlement
- PassOu 2006 p. 203 — influence ranges "2 He and 3 He" for sand and stiff clay
- PassOu 2006 Fig. 6.25(a) — sand: triangular, δv/δvm = 1.0 at the wall, 0.5 at d/He = 1.0, 0 at 2.0
- PassOu 2006 Fig. 6.25(b) — stiff clay: triangular, 1.0 at the wall, 0.5 at d/He = 1.5, 0 at 3.0
- PassOu 2006 p. 203 + Fig. 6.25(c) — soft to medium clay: plateau to d/He = 0.75, then linear to 0 at 2.0
- PassOu 2006 §6.4.4 p. 194 (Fig. 6.14) — δvm = (0.5-0.75)·δhm, Hsieh-Ou range
- PassCFEM 2006 §26.15.2-26.15.4 (pp. 435-437) — zones of influence by ground type
- PassLook 2007 Table 23.15 — medium to dense sand: 0.3 % at the wall, 0.1 % at 1.2 He, 0.0 % at 2.0 He
- PassCraig 2012 Fig. 11.39 (p. 455) — the coarse-grained envelope returns to zero at x/h ≈ 2
- PassLook 2007 Table 23.7 / EC7 WE Table 3.4.1 — 1/500: "safe limit for no cracking" / "cracking in walls"
- PassLook 2007 Table 23.7 — 1/300: "first cracking of panel walls"
- PassLook 2007 Table 23.7 / EC7 WE Table 3.4.1 — 1/150: "considerable cracking" / "structural damage"
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-design-checks-anchor-web-validationW3 FE design check — GROUND ANCHOR — web-validation benchmark against published tables and worked examples.23 passing
Analyses validated: not attributed by the manifest
- Pass[GEC4 Table 10 p.78] 1-strand 1860 MPa tendon (A = 140 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 10 p.78] 3-strand 1860 MPa tendon (A = 420 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 10 p.78] 4-strand 1860 MPa tendon (A = 560 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 10 p.78] 5-strand 1860 MPa tendon (A = 700 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 10 p.78] 7-strand 1860 MPa tendon (A = 980 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 10 p.78] 9-strand 1860 MPa tendon (A = 1260 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 10 p.78] 12-strand 1860 MPa tendon (A = 1680 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 10 p.78] 15-strand 1860 MPa tendon (A = 2100 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 10 p.78] 19-strand 1860 MPa tendon (A = 2660 mm²): f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 9 p.77] 26-mm bar, f_pu = 1035 MPa: f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 9 p.77] 32-mm bar, f_pu = 1035 MPa: f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 9 p.77] 36-mm bar, f_pu = 1035 MPa: f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 9 p.77] 45-mm bar, f_pu = 1035 MPa: f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 9 p.77] 64-mm bar, f_pu = 1035 MPa: f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 9 p.77] 26-mm bar, f_pu = 1104 MPa: f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 9 p.77] 32-mm bar, f_pu = 1104 MPa: f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Table 9 p.77] 36-mm bar, f_pu = 1104 MPa: f_pu·A, 0.8/0.7/0.6·f_pu·A
- Pass[GEC4 Ex.1 p.A-9] soil anchor: bond 600 kN at L = 12 m, required L = 8.9 m, tendons 501 / 469 kN
- Pass[GEC4 Ex.2 p.A-27/28] rock anchor: bond 900 kN at L = 7.5 m, required L = 5.3 m, tendons 675 / 782 kN
- Pass[DG7 Ex.8.1 Table 8.2] DA-1 LEM: R_a,k,req = γa·P_d = 461 kN; EN 1537 proof load = 419 kN
- Pass[DG7 Ex.8.1 Table 8.2] DA-2(L) LEM: R_a,k,req = γa·P_d = 611 kN; EN 1537 proof load = 557 kN
- Pass[DG7 Ex.8.1 Table 8.2] DA-2(S) spring: R_a,k,req = γa·P_d = 421 kN; EN 1537 proof load = 383 kN
- Pass[DG7 Ex.8.1 Table 8.2] DA-3 LEM: R_a,k,req = γa·P_d = 461 kN; EN 1537 proof load = 419 kN
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-design-checks-d277-web-validationW4 (D277) — published benchmarks for the W3 checks that had none: IS 456 RC wall flexure, EN 1993-1-1 strut buckling, FHWA GEC-11 geogrid rupture.9 passing
Analyses validated: not attributed by the manifest
- PassIS 456 — NPTEL M3L7 Problem 3.2 (b 300, d 550, M20, Fe415, A_st 1256): x_u 209.94 mm, M_u 209.43 (direct) / 209.68 kNm (SP-16 Table 2)
- PassIS 456 — NPTEL M3L7 Problem 3.3 (A_st 1658): x_u 277.14 > x_u,max → M_u,lim 250.01 (direct) / 250.47 kNm (SP-16, 2.76 b d²)
- PassIS 456 — NPTEL M3L7 Q.1 (b 300, d 500, M20, Fe500): A_st 452 → x_u 91.03, M_u 90.79 / 90.3 kNm; A_st 1030 → x_u 207.43, M_u 184.99 kNm; x_u,max 230 mm
- PassEN 1993-1-1 — Designers’ Guide Ex. 6.7 (CHS 244.5×10 S355, L 4 m, curve a): N_cr 6571, λ̄ 0.63, Φ 0.74, χ 0.88, N_b,Rd 2297, N_c,Rd 2616 kN
- PassEN 1993-1-1 — Designers’ Guide Ex. 6.9 (A 8300, S355, curve a) y-axis: Φ 0.92, χ 0.77, N_b,Rd 2266 kN
- PassEN 1993-1-1 — Designers’ Guide Ex. 6.9 (A 8300, S355, curve a) z-axis: Φ 1.63, χ 0.41, N_b,Rd 1209.2 kN
- PassGEC-11 Example E1 Table E1-7.3: T_al and T_r = 0.90 T_al for GG-I / GG-II / GG-III (lb/ft)
- PassGEC-11 Example E1 Table E1-7.4: CDR = T_r/T_MAX for all 11 layers
- PassGEC-11 Example E9 Step 4: T_al = 6850/(1.25·1.2·3.0) = 1520 lb/ft (22 kN/m)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-design-checks-geogrid-web-validationW3-3 — `fe-design-checks/geogrid.ts` (the per-element geogrid tension check) against published long-term-strength values.6 passing
Analyses validated: not attributed by the manifest
- PassBS 8006-1 Table 9: f_n = 1.0 / 1.0 / 1.1 for categories 1 / 2 / 3 (printed p. 52)
- PassBS 8006-1 Table 12 combination A: the check default γ_F = f_fs = 1.5 on soil self-weight (printed p. 70)
- PassBS 8006-1 Annex A.3: T_D = T_char/RF with RF = 7 (GEC-11 Eq 3-13 conservative anchor) decomposed as RF_CR·(RF_ID·RF_W·RF_CH·f_s)
- PassGEC-11 (2009) Table 4-7: φ = 0.90 geosynthetic static; (2023) Table 16 SSM: φ = 0.80
- PassGEC-11 Vol II Example E9 Step 4: T_al = 6850/(1.25·1.2·3.0) = 1520 lb/ft (22 kN/m)
- PassGEC-11 Vol II Example E1 Table E1-7.3: T_al and T_r = 0.90 T_al for GG-I / GG-II / GG-III (lb/ft)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-design-checks-pile-web-validationW4 (D276) — embedded pile check: web / published benchmark.13 passing
Analyses validated: not attributed by the manifest
- PassJRC EUR 26227 Ex. 2 (bored, CPT): R_b,k = 284 kN, R_s,k = 101 kN per metre
- PassJRC EUR 26227 Ex. 2: DA1-C1 F_c,d = 630 kN equals R_c,d at L_s = 3.99 m
- PassJRC EUR 26227 Ex. 2: DA1-C2 F_c,d = 495 kN equals R_c,d at L_s = 4.08 m
- PassJRC EUR 26227 Ex. 2: DA2 R_c,d = 630 kN at L_s = 4.05 m
- PassJRC EUR 26227 Ex. 3 (driven, γ_Rd 1.75): R_b,k = 386 kN, R_s,k = 153 kN per metre
- PassJRC EUR 26227 Ex. 3 EN 1997-1 DA1-C1: R_c,d = 221 + 87.4·L_s; = F_c,d 1260 kN at L_s = 11.9 m
- PassJRC EUR 26227 Ex. 3 EN 1997-1 DA1-C2: R_c,d = 170 + 67.3·L_s; = F_c,d 990 kN at L_s = 12.2 m
- PassJRC EUR 26227 Ex. 3 EN 1997-1 DA2: R_c,d = 201 + 79.5·L_s; = F_c,d 1260 kN at L_s = 13.3 m
- PassEN 1992-1-1 §2.3.4.2(2) design diameter of an uncased cast-in-place pile (code rule, 4 values)
- Passstructural (golden, hand-evaluated): d 0.6 m uncased C30/37, 8 H20 (2513 mm²), B500
- Passplain concrete uses α_cc,pl = 0.8; precast/cased uses the nominal diameter and γ_c = 1.5
- Passnever defaults: missing pile type, resistances and section → incomplete with every field named
- Passtension: R_t,d = R_s,k/γ_s,t (Table A.7 R1: 1.25); dispatcher converts the kernel sign (tension +)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-design-checks-rc-wall-web-validationWeb / published-benchmark validation — RC wall design check (fe-design-checks/rc-wall.ts).13 passing
Analyses validated: not attributed by the manifest
- PassEC2 M_Rd — [JRC] p.58, T-beam mid-span AB (b_eff 2611.2, d 372): MEd 89.3 → As 556 mm²
- PassEC2 M_Rd — [JRC] p.58, T-beam support B (b_w 250, d 372): MEd 132.9 → As 947 mm²
- PassEC2 M_Rd — [JRC] pp.65–66, slab X-dir support axis 2 (d 143): MEd 49.18 → As 856 mm²/m
- PassEC2 M_Rd — [JRC] p.66, slab X-dir mid-span 1-2: MEd 18.32 → As 303 mm²/m
- PassEC2 M_Rd — [JRC] p.66, slab X-dir mid-span 2-3 / axis 3: MEd 36.95 → As 630 mm²/m
- PassEC2 M_Rd — [JRC] pp.66–67, slab Y-dir support axis B: MEd 68.15 → As 1235 mm²/m
- PassEC2 M_Rd — [JRC] p.67, slab Y-dir mid-span: MEd 52.14 → As 915 mm²/m
- PassEC2 V_Rd,c — [JRC] p.59 beam support A: bw 250, d 372, Asl 565, C25 → k 1.73, ρl 0.61 %, V_Rd,c 47.90 kN
- PassEC2 V_Rd,c — [JRC] p.92 slab with embedded lighting: bw 240, d 190, ρl = 0.02 (cap), k = 2.0 → 40.2 kN
- PassEC2 v_Rd,c / v_min — [JRC] p.73 (punching, same Eq. 6.47 ≡ 6.2a form): d 164 → k 2.0, ρl 0.83 %, v_Rd,c 0.66, v_min 0.49 MPa
- PassACI φM_n — [SP] p.4: b 12 in, d 9.75 in, f'c 3000 psi, fy 60 ksi, As 0.316 in²/ft → φM_n = M_u 13.4 kip·ft/ft
- PassACI stress block — [SP] p.4: As 0.321 in²/ft → a 0.629 in, c 0.74 in, εt 0.037 (> 0.005, tension-controlled)
- PassACI φV_c Eq. (a) — [SP] p.3: φ·2λ√f'c·bw·d, bw 12 in, d 9.75 in, 3000 psi → 9.61 kips/ft
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-design-checks-sheet-pile-web-validationFE-DESIGN-CHECKS / SHEET PILE — benchmark against published worked examples (EN 1993-5:2007).12 passing
Analyses validated: not attributed by the manifest
- PassPU 18 (Ex. 1) — §8.3 M_c,Rd = 568; §8.4 A_v 3769, V_pl,Rd 772.5 kN/web, 1288 kN/m
- PassPU 18 (Ex. 1) — §8.5 V_Ed 800: M_V,Rd/M_c,Rd 0.971, M_V,Rd 552; §8.8 ρ 0.059
- PassPU 18 (Ex. 1) — §8.6/8.7 N_pl,Rd 5797, N/N_pl 0.259, M_N,Rd 560
- PassPU 18 (Ex. 1) — §8.8 V 800 + N 1500: f_y,red 334.2, M_c,Rd 535, N_pl,Rd 5456, M_N,Rd 516
- PassPU 18 (Ex. 1) — §8.9 member buckling: N_cr 32697, 0.04N_cr 1308, λ̄ 0.421, χ 0.84 (chart), M_Ed ≤ 297
- PassAZ 18-700 (Ex. 2) — M_c,Rd 639; A_v 3699, V_pl,Rd 758.1 kN/web, 1083 kN/m
- PassAZ 18-700 (Ex. 2) — V_Ed 800: ratio 0.94, M_V,Rd 601 (class 3, elastic analogue)
- PassAZ 18-700 (Ex. 2) — N_pl,Rd 4942, N/N_pl 0.304, M_N,Rd 445
- PassAZ 18-700 (Ex. 2) — V 800 + N 1500: ρ 0.228, f_y,red 274.1, M_c,Rd 493, N_pl,Rd 3815, M_N,Rd 299
- PassHandbook Ch. 3 Table 3.7 — M_c,Rd for AZ 25-800 / PU 28-1.0 in S 430 GP (new and corroded)
- PassHandbook Table 8.7 — AZ 18-700 slant height c 527.4 mm and (c/t_w)/ε 75.5 / 79.3 / 82.0 (S 390 / 430 / 460)
- Passdocumented difference — AZ 18-700 S 355: (c/t_w)/ε = 72.02 > 72 so the engine applies the shear-buckling clause
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-design-checks-strut-web-validationW3-3 — `fe-design-checks/strut.ts` (the per-element strut check) against published column-buckling values.6 passing
Analyses validated: not attributed by the manifest
- PassENV 1993-1-1 Table 5.5.2 — curve a (α = 0.21), λ̄ = 0.2…1.5 (14 published χ values)
- PassENV 1993-1-1 Table 5.5.2 — curve a (α = 0.21), λ̄ = 1.6…3.0 (15 published χ values)
- PassENV 1993-1-1 Table 5.5.2 — curve b (α = 0.34), λ̄ = 0.2…1.1 (10 published χ values)
- PassDesigners’ Guide Ex. 6.7 (CHS 244.5×10 S355, L 4 m, curve a): N_b,Rd 2297, N_c,Rd 2616 kN
- PassDesigners’ Guide Ex. 6.9 (A 8300, S355, curve a) y-axis: N_b,Rd 2266 kN, N_c,Rd 2946.5 kN
- PassDesigners’ Guide Ex. 6.9 (A 8300, S355, curve a) z-axis: N_b,Rd 1209.2 kN, N_c,Rd 2946.5 kN
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-staged-excavation-web-validationWEB-BENCHMARK validation for the staged-excavation FE engine.5 passing
Analyses validated: fe-staged-excavation
- PassSE web: wide-cut collapse stability number in the basal-heave band [4, 5.5] (≈ Prandtl 5.14)
- PassSE web: base heave builds up progressively through the stages
- PassSE web: FoS falls as the cut deepens
- PassSE web: higher cu ⇒ deeper stable excavation
- PassSE web: heave field + per-stage results are well-formed
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
ground-anchor-web-validationrecords a differenceGROUND-ANCHOR — web-validation benchmark against FHWA GEC-4 tables and design examples.11 passing
Analyses validated: ground-anchor
- PassGEC-4 Table 9 — Grade 150 bars (f_pu = 1035 MPa): 0.8 / 0.7 / 0.6 f_pu·A_ps
- PassGEC-4 Table 9 — Grade 160 bars (f_pu = 1104 MPa): 0.8 / 0.7 / 0.6 f_pu·A_ps
- PassGEC-4 Table 10 — strand tendons: 0.8 / 0.7 / 0.6 f_pu·A_ps for 1, 3, 4, 5, 7, 9, 12, 15, 19 strands
- PassGEC-4 Design Example 1 (pp. A-8, A-9) — soil anchor: 12 m bond length at 100 kN/m, FoS 2.0
- PassGEC-4 Design Example 1 (p. A-9) — tendon selection against the 445 kN design load
- PassGEC-4 Design Example 2 (pp. A-26, A-27) — rock anchor: 7.5 m bond length at 360 kN/m, FoS 3.0
- PassGEC-4 Design Example 2 (p. A-27) — tendon selection against the 636 kN design load
- PassGEC-4 p. 74 (PTI 1996) — ultimate rock-grout bond ≈ 10 % of UCS, maximum 3.1 MPa
- PassCFEM 2006 Table 26.6 (p. 423) — soil anchors: ultimate load transfer per metre of bond length
- PassCFEM 2006 Table 26.7 (p. 424) — rock anchors: ultimate load transfer per metre of bond length
- PassCFEM 2006 §26.12.4.1 — allowable anchor load = ultimate capacity / 3 where no pull-out test is made
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
k0-at-rest-web-validationrecords a differenceValidation for `k0-at-rest` — Jaky / Mayne-Kulhawy coefficient of earth pressure at rest and the at-rest wall thrust (`k0-at-rest.ts`).9 passing
Analyses validated: k0-at-rest
- PassEM 1110-2-2502 Table E-1: Jaky K0 for φ′ = 10°…27° (printed 0.826 … 0.546)
- PassEM 1110-2-2502 Table E-1: Jaky K0 for φ′ = 28°…45° (printed 0.531 … 0.293)
- PassDas Example 12.1: K0 = 0.5, σ′h = 20.63 kN/m² at 2.5 m, triangle force 25.788, lever arm 0.833 m
- PassLambe & Whitman Example 8.2: initial horizontal stress K0·γ·z = 24.8 kN/m² at 3 m
- PassNAVFAC DM-7.02: "for φ′ = 30°, K0 = 0.5"
- PassBowles: K0 printed in Examples 4-10, 13-6, 16-1 and the Ch. 12 abutment discussion
- PassBowles Example 14-1: K0 = 0.50, R0 = ½ × 16.5 × 9.3² × 0.5 = 357 kN, average pressure 38.38 kPa
- PassBowles Example 2-2 (φ′ = 25°, OCR = 5): K0,nc = 0.58 and K0,OCR = 1.14 / 1.15
- PassBowles §2-8: a fluid has K0 = 1.0, the isotropic limit of Jaky at φ′ = 0
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mse-wall-web-validation`mse-wall` — anchored to the FHWA GEC-11 worked example.10 passing
Analyses validated: mse-wall
- PassGEC-11 Example E1: backslope angle I = arctan(9/40) = 12.7°
- PassGEC-11 Vol I Eq. 4-3: the Coulomb Ψ term = 2.133 at Example E1’s conditions
- PassGEC-11 Vol I Eq. 4-2: external coefficient Kab = 0.360, and our engine reproduces it
- Passthe Coulomb (δ = β, θ = 90°) and Rankine-sloped forms are IDENTICAL — swept, not assumed
- PassGEC-11 Eq. 4-28 / 4-29 / 4-30: the published EV load factor is 1.35 and heq = 2 ft
- PassGEC-11 Example E1: the engine runs the published geometry and reports coherent externals
- Pass§4.4.2: the external thrust uses the RETAINED soil, and a weaker retained soil raises it
- Pass§4.3.2: a vertical spacing above 0.8 m is warned
- Passa backslope steeper than the retained friction angle is refused, not silently zeroed
- Passevery numeric output is finite at the published configuration
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rc-section-web-validationrecords a differenceDedicated validation for the singly-reinforced RC flexural section (`rc-section.ts`): limit-state flexure to IS 456:2000 cl.9 passing
Analyses validated: rc-section
- PassSP 16 Table 3 (fck 25): Fe 415 column, printed pt (%) against Mu/bd²
- PassSP 16 Table 3 (fck 25): Fe 250, Fe 500, Fe 480 and Fe 240 columns
- PassSP 16 Table 3 blanks: Mu/bd² above the Table D limit is not a singly-reinforced design
- PassSP 16 Table C: Mu,lim / (fck b d²) for Fe 250, 415, 500 (printed to 3 d.p.)
- PassSP 16 Table D: Mu,lim / bd² (N/mm²) for fck 15-30 and Fe 250/415/500
- PassSP 16 Example 1: 30 x 60 cm beam, M 15, Fe 415, Mu = 170 kN·m, d = 56.25 cm
- PassSP 16 Example 2: slab, 10 cm thick, d = 8 cm, Mu = 9.60 kN·m/m, M 15 — printed limiting moments
- PassIS 456:2000 cl.38.1 Note: xu,max/d = 0.53, 0.48, 0.46 for Fe 250, 415, 500 (printed to 2 d.p.)
- PassNPTEL Lesson 6 Design Problem 3.1: printed limiting depth, Ast and Mu,lim
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
retaining-wall-web-validationrecords a differenceRETAINING-WALL — web-validation benchmark against published worked examples and Rankine tables.7 passing
Analyses validated: retaining-wall
- PassBowles Ex. 12-6 — geometry and heel-plane thrust: B = 1.98 m, H′ = 2.90 m, Pa = 44.30 kN/m, Mo = 49.75
- PassBowles Ex. 12-6 — Table E12-6: weights and moments about the toe
- PassBowles Ex. 12-6 — resultant position and eccentricity: x̄ = 0.70 m, e = 0.29 m < B/6 = 0.33 m
- PassBowles Ex. 12-6 — the Rankine coefficient the book set aside: Table 11-3 gives 0.260 for φ = 36°
- PassBowles Ex. 12-5 (p. 772) — Pa = 96.28 kN/m, Mo = 245.58 kN·m/m and the two concrete parts
- PassBowles 5e Table 11-3 (p. 603) — Rankine Ka, β = 0, φ = 26°…42°
- PassDas 8e Table 12.1 (p. 608) — Ka(R) at α = 0°, θ = 0°, φ′ = 28°…40°
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
secant-pile-wall-web-validationWeb-benchmark validation for `secant-pile-wall`.12 passing
Analyses validated: secant-pile-wall
- Passwatertightness is the overlap left AFTER verticality tolerance, vs 0.10·D
- Passa deeper wall loses more overlap and eventually fails watertightness
- Passthe overlap must be geometrically possible
- Passper-pile actions use pitch = Ds + Dp − 2·ov, halved for hard/hard
- Passa wider overlap tightens the pitch and so reduces the load per pile
- Passmoment capacity is IS 456 M_lim = 0.138·f_ck·Ds·d_eff², with d_eff floored (E-12)
- Passa below-grade secondary concrete grade is flagged against DIN 4126 §7
- Passvertical capacity uses the Tomlinson α bands and 9·s_u end bearing, with FoS 2.5
- Passin sand the capacity is K₀·σv·tanδ shaft plus a halved Meyerhof base
- Passbasal heave uses N_c = 7 on γ_top·H + q, and withholds in a frictional soil
- Passa prop reduces the wall moment and its force is reported per metre and per pile
- Passinvalid geometry is refused with a zeroed result
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
seismic-structural-web-validationWeb-benchmark validation for TWELVE seismic, structural and deep-foundation runner engines.12 passing
Analyses validated: bray-travasarou, concrete-durability, design-spectrum, embankment-stress, excavation-settlement, helical-pile, machine-foundation, makdisi-seed, newmark-displacement, rc-section, strut-design, tunnel-ground-reaction
- Passmakdisi-seed uses the 1978 fundamental period and normalised displacement
- Passnewmark-displacement reproduces the Jibson (2007) regression
- Passbray-travasarou reproduces the 2007 flexible-sliding-mass regression
- Passdesign-spectrum follows IS 1893 (Part 1):2016 Cl 6.4.2
- Passstrut-design reproduces the IS 800:2007 Perry-Robertson buckling curve
- Passrc-section reproduces IS 456:2000 Cl 38 flexure and the steel limits
- Passconcrete-durability applies the IS 456 Table 4 sulphate classes
- Passmachine-foundation reproduces the Barkan C_u stiffness and the SDOF response
- Passtunnel-ground-reaction reproduces the Hoek convergence-confinement solution
- Passexcavation-settlement applies the Clough & O'Rourke (1990) envelopes
- Passembankment-stress uses the Osterberg (1957) trapezoidal influence
- Passhelical-pile reproduces the AC358 individual-bearing plate method
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
sheet-pile-second-source-web-validationSHEET-PILE — second-source web-validation suite (companion to `sheet-pile-web-validation.test.ts`).7 passing
Analyses validated: sheet-pile
- PassBowles 5e Table 11-3 (p. 603) — Rankine Ka, β = 0, φ = 26°…42°
- PassBowles 5e Table 11-4 (p. 603) — Rankine Kp, β = 0, φ = 26°…42°
- PassVarghese Ex. 22.4 (p. 420) — active pressure at the tie level and at the dredge line
- PassVarghese Ex. 22.4 (p. 420) — the net pressure returns to zero a = 1.0 m below the dredge line
- PassVarghese Ex. 22.3 (p. 419) — active pressures at the water table and at the dredge line
- PassEx. 22.4 — engine embedment equals the root of the moment equation the book states (3.113 m), not the printed 6.3 m
- PassEx. 22.3 — engine embedment equals the root of the correct cantilever equilibrium (7.455 m), not the printed 6.35 m
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
sheet-pile-web-validationSHEET-PILE WALLS — web-validation benchmark against published worked examples.15 passing
Analyses validated: sheet-pile
- PassDas Ex 14.1 — Rankine coefficients and the pressure diagram (10 published values)
- PassDas Ex 14.1 — quartic coefficients A1..A4 (Eqs 14.17-14.20)
- PassDas Ex 14.1 — L4 is a trial-and-error stop at 4.8 m, not a rounding (proof by residual)
- PassDas Ex 14.1 — Mmax, section modulus and total length (parts b and c)
- PassDas Ex 14.2 — the no-water-table case falls out of the SAME implementation
- PassDas Ex 14.2 — Eq (14.30) for z̄ is an erratum: the Ka coefficient is 1, not 2
- PassDas Ex 14.7 — anchored free-earth support, 12 published values
- PassDas Ex 14.7 — F, x and Mmax reproduce EXACTLY at the L4 the text prints
- PassDas Ex 14.9 — total pile length H′ = L1 + L2 + Dactual = 14.48 m
- Passanchored free-earth diagram satisfies ΣF = 0 AND ΣM = 0 at the toe
- Passcantilever toe moment residual equals Das Eq (14.14)’s trapezoid-arm idealisation exactly
- Passrankine_classical reproduces Ex 14.1 end-to-end through computeSheetPile
- PassE-51 — net_envelope is conservative by a pinned factor, not by an unknown one
- Passrankine_classical refuses every case Das §14.4/§14.9 does not derive
- Passrankine_classical honours Das’s Kp factor of safety (Step 13 note)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
soil-nail-wall-web-validation`soil-nail-wall` — anchored to FHWA GEC No.8 passing
Analyses validated: soil-nail-wall
- PassE-44: the default overall-stability target is Table 5.1’s 1.5, not note (2)’s 1.35
- PassE-44: opting into FSOS = 1.35 is allowed but its note-(2) conditions are stated
- PassGEC No. 7 Table 5.1: the static acceptance targets are 2.0 pullout, 1.8 tendon, 1.5 facing
- PassE-45: under seismic loading the SEISMIC column applies (FSPO 1.5, FST 1.35, FSFF 1.1)
- PassE-45: the published seismic FSOS is 1.1 — not 0.75 × the static target
- PassTable 5.1 internal consistency: every seismic target is at or below its static counterpart
- Passthe engine cites the CURRENT edition, FHWA-NHI-14-007 (GEC No. 7, 2015)
- Passevery numeric output is finite, and a wall with no nails is refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
staged-excavation-wall-web-validationrecords a differenceSTAGED-EXCAVATION-WALL (and EMBEDDED-WALL-SSI) — web-validation benchmark: the published parts.4 passing
Analyses validated: embedded-wall-ssi, staged-excavation-wall
- PassFHWA NHI-06-089 Example 10-2 (pp. 10-32, 10-33) — line-load lateral pressure Ph (psf) at n = z/H = 0.1 … 1.0
- PassNAVFAC DM-7.2 Fig. 11 (p. 7.2-74) — line load, m > 0.4: P_H = 0.64 Q_L/(m² + 1)
- PassNAVFAC DM-7.2 Fig. 11 (p. 7.2-74) — height R of the resultant above the base, as a fraction of H
- PassNAVFAC DM-7.2 Fig. 30 (p. 7.2-107) — surcharge step: m = 4/20 = 0.2, Qp = 10 kip, H = 20 ft
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
steel-section-mphi-web-validationSteel circular / pipe pile section engine (`steel-section-mphi.ts`, registered as `steel-pile-section`) checked against PUBLISHED tabulated section properties.20 passing
Analyses validated: steel-pile-section
- Pass[1] ASTM A1085 20 x 0.5 in: I = 1460 in⁴, S = 146 in³, Z = 190 in³
- Pass[1] ASTM A1085 20 x 0.375 in: I = 1110 in⁴, S = 111 in³, Z = 144 in³
- Pass[1] ASTM A1085 18 x 0.5 in: I = 1050 in⁴, S = 117 in³, Z = 153 in³
- Pass[1] ASTM A1085 16 x 0.625 in: I = 894 in⁴, S = 112 in³, Z = 148 in³
- Pass[1] ASTM A1085 16 x 0.5 in: I = 732 in⁴, S = 91.5 in³, Z = 120 in³
- Pass[1] ASTM A1085 14 x 0.375 in: I = 373 in⁴, S = 53.3 in³, Z = 69.6 in³
- Pass[1] ASTM A1085 12.75 x 0.5 in: I = 362 in⁴, S = 56.7 in³, Z = 75.1 in³
- Pass[1] ASTM A1085 12.75 x 0.25 in: I = 192 in⁴, S = 30.1 in³, Z = 39.1 in³
- Pass[1] ASTM A1085 10.75 x 0.375 in: I = 165 in⁴, S = 30.6 in³, Z = 40.4 in³
- Pass[1] ASTM A1085 10 x 0.25 in: I = 91.1 in⁴, S = 18.2 in³, Z = 23.8 in³
- Pass[1] ASTM A1085 8.625 x 0.322 in: I = 72.5 in⁴, S = 16.8 in³, Z = 22.2 in³
- Pass[1] ASTM A1085 6.625 x 0.25 in: I = 25.5 in⁴, S = 7.69 in³, Z = 10.2 in³
- Pass[1] ASTM A1085 5 x 0.188 in: I = 8.24 in⁴, S = 3.30 in³, Z = 4.36 in³
- Pass[2] AISC v16 Pipe12STD (OD 12.75 in, tdes 0.349 in): I = 262 in⁴, S = 41 in³, Z = 53.7 in³
- Pass[2] AISC v16 Pipe6STD (OD 6.625 in, tdes 0.261 in): I = 26.5 in⁴, S = 7.99 in³, Z = 10.6 in³
- Pass[3] the printed Mp/Ms ratios: 1.3 for Pipe12STD and 1.4 for Pipe12XXS (the thicker wall has the larger shape factor)
- Pass[4] solid circle r = 2: Z = 32/3, S = 2π, shape factor f = 16/(3π) = 1.697653
- Pass[5] solid circle r = 1: Z = 4/3, S = π/4
- Pass[6] HAND CHECK (not a published value): Mp and My are fy·Z and fy·S, and axial load lowers Mp by the exact circular plastic M–N value
- Pass[7] IS 800:2007 cl. 9.3.1.1(e): for a circular hollow tube Mnd = 1.04·Md·(1 − n^1.7) ≤ Md — the engine's exact reduction is the same order and never exceeds Md
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
structural-elements-web-validationWEB / TEXTBOOK-BENCHMARK validation for the structural-elements engine (beam-on-elastic-foundation Winkler FE + 2-D elasto-plastic FE structure library: beam/plate, anchor, tension-only geogrid, Mohr-Coulomb interface).28 passing
Analyses validated: structural-elements
- PassSE web 1-3: λ = (k/4EI)^(1/4) — Hetenyi 1946 Eq 8
- PassSE web 4-6: infinite beam w_max = P·λ/(2k) — Hetenyi 1946 Eq 17
- PassSE web 7-9: infinite beam M_max = P/(4λ) — Hetenyi 1946 Eq 17
- PassSE web 10-11: infinite beam soil reaction ∫k·w dx = P (Hetenyi equilibrium)
- PassSE web 12: infinite beam shear jump |V| = P/2 at the load (Hetenyi Eq 17)
- PassSE web 13-14: full-length UDL — interior w = q/k, interior M ≈ 0 ("floating" beam)
- PassSE web 15-17: anchor spring — rigid beam, w = P/(kL+k_a) and T = k_a·δ
- PassSE web 18-19: anchor pre-stress — T = P0 + k_a·δ and w = (P−P0)/(kL+k_a)
- PassSE web 20-21: geogrid carries T = k_g·δ in tension (stretched)
- PassSE web 22-23: geogrid carries ZERO force in compression (tension-only)
- PassSE web 24: interface strength cap τ_max = c + σ_n·tan δ (Mohr-Coulomb)
- PassSE web 25-26: interface elastic below cap — τ = k_s·slip, |τ| < τ_max
- PassSE web 27-28: interface caps shear at τ_max under a large load (plastic slip)
- PassSE web 29: superposition — response to (P1)+(P2) = response to both together
- PassSE web 30: symmetry — a symmetric load pair gives a symmetric deflection profile
- PassSE web 31: static equilibrium — ΣFᵥ ≈ 0 and ΣM ≈ 0 for a multi-load case
- PassSE web 32: invalid inputs return errors without throwing (NaN/∞ guard)
- PassSE web 33: all profile outputs are finite for a well-posed problem
- Passaudit: a solve that fails its own equilibrium check is REFUSED, not reported
- Passaudit: the real, valid case is byte-identical to before the fix
- PassSE published: Hetényi §18 — λ and λl (p. 47)
- PassSE published: Hetényi §18 — deflections, soil pressures, M and Q at C of the free-ended beam (pp. 48-49)
- PassSE published: Hetényi §12 Example 1 — forces at x = π/2λ reduce the maximum moment (0.7921 / 0.5842 / 0.7489)
- PassSE published: Hetényi §12 Example 4 — ring on a long tube: bending stress 82 % above the hoop stress (p. 36)
- PassSE published: Bowles Example 9-6 — the 13 printed nodal deflections (COMP X, mm)
- PassSE published: Bowles Example 9-6 — printed soil pressures (SOIL Q, kPa) at nodes 1, 4, 7, 10, 13
- PassSE published: Bowles Example 9-6 — printed nodal bending moments (kN·m), sign per Bowles
- PassSE published: Bowles Example 9-6 — comment 1: Σ spring forces 3374.71 kN against 3375 kN input
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
strut-design-web-validationSTRUT-DESIGN — web-validation benchmark against two independently published column-curve tables.15 passing
Analyses validated: strut-design
- PassIS 800:2007 Table 9(a) (printed p.40) — class a, fy = 250 MPa, KL/r 10…250 (25 published values)
- PassIS 800:2007 Table 9(a) (printed p.40) — class a, fy = 300 and 450 MPa columns (12 published values)
- PassIS 800:2007 Table 9(b) (printed p.41) — class b, fy = 250 MPa, KL/r 10…250 (25 published values)
- PassIS 800:2007 Table 9(b) (printed p.41) — class b, fy = 300 and 450 MPa columns (12 published values)
- PassIS 800:2007 Table 9(c) (printed p.42) — class c, fy = 250 MPa, KL/r 10…250 (25 published values)
- PassIS 800:2007 Table 9(c) (printed p.42) — class c, fy = 300 and 450 MPa columns (12 published values)
- PassIS 800:2007 Table 9(d) (printed p.43) — class d, fy = 250 MPa, KL/r 10…250 (25 published values)
- PassIS 800:2007 Table 9(d) (printed p.43) — class d, fy = 300 and 450 MPa columns (12 published values)
- PassENV 1993-1-1:1992 Table 5.5.2 (p.73) — buckling curve a, λ̄ = 0.2…3.0 (29 published values)
- PassENV 1993-1-1:1992 Table 5.5.2 (p.73) — buckling curve b, λ̄ = 0.2…3.0 (29 published values)
- PassENV 1993-1-1:1992 Table 5.5.2 (p.73) — buckling curve c, λ̄ = 0.2…3.0 (29 published values)
- PassENV 1993-1-1:1992 Table 5.5.2 (p.73) — buckling curve d, λ̄ = 0.2…3.0 (29 published values)
- PassENV 1993-1-1:1992 cl. 5.5.1.2(1): λ1 = 93.9 ε at fy = 235 MPa — KL/r = 93.9 is λ̄ = 1.000
- PassIS 800:2007 Table 3 item (i), cl. 3.8 (p. 20): KL/r limit of 180 for a member in compression from dead + imposed load
- PassDependent arithmetic (NOT a published answer): Pd = Ae·fcd (IS 800 cl. 7.1.2) applied to the printed f_cd
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
wall-surcharge-web-validationValidation for the non-uniform wall-surcharge (NAVFAC modified-Boussinesq) + passive-berm additions to the embedded-wall engine (`staged-excavation-wall.ts`).13 passing
Analyses validated: embedded-wall-ssi, staged-excavation-wall
- PassNAVFAC line load I_L = σh·H/Q_L — published values, m ≤ 0.4 branch
- PassNAVFAC line load I_L — published values, m > 0.4 branch
- PassNAVFAC point load I_P = σh·H²/Q_P — published values, m ≤ 0.4 branch
- PassNAVFAC point load I_P — published values, m > 0.4 branch
- PassNAVFAC line load: resultant ≈ 0.64·Q for m > 0.4 (closed form)
- PassNAVFAC line load: pressure peaks at n = m/√3 (m > 0.4)
- PassNAVFAC line load: linear in Q, and → 0 at surface and at depth
- PassNAVFAC point load: linear in Q, correct Q/H² scaling, decays
- Passstrip surcharge → line-load limit as width → 0 with q·w = Q
- Passstrip surcharge superposes and stays positive; wide strip spreads the pressure
- Passwall: a retained strip surcharge raises the bending moment
- Passwall: a passive berm reduces wall deflection (CIRIA C760)
- Passno surcharges / no berm ⇒ unchanged from the base wall (regression guard)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
walls-web-validationWEB-BENCHMARK validation for the retaining-wall external-stability engine (the release rules ≥20 cited-value gate).6 passing
Analyses validated: retaining-wall
- PassWall web: φ=25° — Ka, Pa, overturning & sliding FoS (Rankine + Das §8)
- PassWall web: φ=30° — Ka, Pa, overturning & sliding FoS (Rankine + Das §8)
- PassWall web: φ=35° — Ka, Pa, overturning & sliding FoS (Rankine + Das §8)
- PassWall web: φ=40° — Ka, Pa, overturning & sliding FoS (Rankine + Das §8)
- PassWall web: φ=30° — eccentricity e & q_max (middle-third, Bowles §11)
- PassWall web: φ=35° — eccentricity e & q_max (middle-third, Bowles §11)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Piles and deep foundations
0 finite-element rows · 0 closed-form problems · 30 validation suites
Cited validation suites
broms-lateral-pile-web-validationrecords a differencePUBLISHED-VALUES: 9 -- distinct published values for this engine (engine-level total, declared once); independent audit A2: 9 printed values; the further 30 assertions are digitised chart readings (+-5 %) and are not counted.15 passing
Analyses validated: broms-lateral-pile
- PassFHWA-NHI-10-016 Eq.12-21/12-22/12-24 clay case A (Pt=100 kip, Mt=2000 kip-ft): Hu from printed Mmax
- PassFHWA clay case A: depth of maximum moment = 1.5·Bb + f = 72 + 15.43 in
- PassFHWA Eq.12-25/12-26 clay case B (Pt=40 kip, Mt=800 kip-ft): Hu and hinge depth from printed Mmax
- PassFHWA clay: printed Mmax (1,050 kip-ft) given in kip-ft returns the same 40 kip
- PassFHWA Eq.12-33: Kp = tan²(45°+32°/2) = 3.25
- PassFHWA sand: Hu from the printed Mmax = 956 kip-ft returns Pt = 40 kip
- PassFHWA Eq.12-35: sand depth of maximum moment f = 5.85 ft
- PassVarghese Example 13.3: long free-head pile in clay, Hu ≈ 7·cu·D² = 63 kN
- PassDas Fig. 9.36(b): My/(cu·D³) = 40, free-head curves e/D = 0,1,2,4,8,16
- PassDas Fig. 9.36(b): My/(cu·D³) = 100, free-head curves e/D = 0,1,2,4,8,16
- PassDas Fig. 9.36(b): My/(cu·D³) = 200, free-head curves e/D = 0,1,2,4,8,16
- PassDas Fig. 9.36(b): My/(cu·D³) = 400, free-head curves e/D = 0,1,2,4,8,16
- PassDas Fig. 9.36(b): the six marked long-pile points
- PassP&D Fig. 7.9(a) clay short piles, free head: L/d = 10, 14, 18
- PassP&D Fig. 7.12(a) sand short piles: free head e/L = 0, 0.2, 0.4 and the restrained line
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
drilled-shaft-web-validationrecords a differencePublished-value validation for drilled-shaft axial capacity (`drilled-shaft.ts`, `computeDrilledShaft`): α-method side, β-method side, and base resistance in clay and sand.18 passing
Analyses validated: drilled-shaft
- PassDas Example 10.5: Σ αcu·p·ΔL = 255.28 kN (ΔL1 = 1.5 m at cu 40, ΔL2 = 2.24 m at cu 60)
- PassDas Example 10.5: qp = 6cu(1 + 0.2L/Db) = 1957.5 kPa exceeds 9cu, so qp = 1305 kPa
- PassDas Example 10.5: base resistance qp·Ap = 1475.9 kN
- PassDas Example 10.4: base in cu = 2175 psf clay, Ds = 3.3 ft: Qp(net) = Ap·cu·N*c = 167.4 kip
- PassDas Example 10.3: qp = 57.5·N60 = 57.5 × 30 = 1725 kN/m²
- PassDas Table 10.4: cu/pa = 0.25, 0.5, ≥1 → N*c = 6.5, 8.0, 9.0 (pa = 100 kPa)
- PassFHWA Table 13-2: su = 500, 1000, 2000 psf → N*c = 6.5, 8.0, 9.0
- PassFHWA Example 13-2: unit side resistance 0.55 × 2,395 psf = 1,317 psf
- PassFHWA Example 13-2: RSN = π (5 ft)(45 ft)(1,317 psf) = 930.9 kips
- PassFHWA App. A layer 4: fSN = 0.55 × 1,750 = 963 psf (962.5 printed as 963)
- PassFHWA App. A layer 4: RSN = π (8 ft)(15 ft)(962.5 psf) = 362,854 lb
- PassFHWA App. A layer 6: fSN = 0.55 × 2,300 = 1,265 psf
- PassFHWA App. A layer 6: RSN = 2,559,330 lb
- PassFHWA App. A layer 7 base: qBN = 0.60 N60 = 24.6 tsf = 49.2 ksf (N60 = 41)
- PassFHWA App. A layer 7 base: RBN = π/4 (8 ft)² (49.2 ksf) = 2,473 kips
- PassAASHTO (2007) Eq. 10.8.3.5.2c-1: qp = 0.057 N60 MPa → 1710 kPa at N60 = 30
- PassAASHTO (2007) §10.8.3.5.2c: tip resistance limited to 3.0 MPa; FHWA Eq. 13-14: 30 tsf = 2,873 kPa
- PassAASHTO (2007) Eq. 10.8.3.5.2b-1 / Das Eq. 10.26: unit side resistance in sand never exceeds 0.19 MPa (192 kN/m²)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
driven-pile-dynamics-web-validationPublished-value validation for the Hiley driven-pile dynamic formula (`driven-pile-dynamics.ts`, `computeDrivenPileDynamics`).26 passing
Analyses validated: driven-pile-dynamics
- PassIRC:78-2014 App.7 η table, P/W = 0.5: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 1: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 1.5: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 2: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 2.5: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 3: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 3.5: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 4: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 5: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 6: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 7: e = 0.5, 0.4, 0.32, 0.25, 0
- PassIRC:78-2014 App.7 η table, P/W = 8: e = 0.5, 0.4, 0.32, 0.25, 0
- PassBowles Example 17-2: first trial k2 = 6.8 mm gives Pu = 1331 kN (printed "rounded")
- PassBowles Example 17-2: converged k2 = 9.5 mm gives Pu = 1264 kN
- PassBowles Example 17-2: blow-efficiency term (125 + 0.5²·21.86)/(125 + 21.86) = 0.888
- PassBowles Example 17-2: hammer energy term eh·Eh = 0.78 × 48.8 = 38.06 kN·m
- PassBowles Example 17-2: allowable Pa = 1260/4 = 315 kN at the book's rounded Pu = 1260
- PassBowles Table E17-4: set 1, 2, 4 mm → Pu 901.4, 849.8, 758.2 kN
- PassBowles Table E17-4: set 6, 8, 10 mm → Pu 679.0, 611.3, 553.4 kN
- PassBowles Table E17-4: set 25, 50 mm → Pu 307.9, 170.2 kN
- PassVarghese Example 10.1: efficiency of blow η = (5 + 9.7·0.25²)/(5 + 9.7) = 0.381
- PassVarghese Example 10.1: total temporary compression C = 0.212 + 1.222 + 0.409 = 1.843 cm
- PassVarghese Example 10.1: set S = 0.95 mm/blow gives Ru = 300 t (safe 120 t at FS 2.5)
- PassVarghese Example 10.2 resistance-set table: Ru 250, 200, 150, 100 t at S = 2.98, 6.03, 11.10, 21.27 mm
- PassVarghese Example 10.2: Ru for S → 0 is 331 t (hammer energy over C/2 alone)
- PassVarghese Example 10.3 (400×400, 15 m, fall 1.5 m): η = 0.48 and S = 2.0 mm gives Ru = 225 t
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
helical-pile-web-validationrecords a differencePublished-value validation for helical (screw) pile capacity (`helical-pile.ts`, `computeHelicalPile`): individual-plate bearing Qh = Ah·(9·c + q'·Nq) and the installation-torque correlation Qu = Kt·T.19 passing
Analyses validated: helical-pile
- PassSupportworks Example 1: net plate areas 10/12/14 in. on a 2.875 in. shaft = 0.50/0.74/1.02 ft²
- PassSupportworks Example 1: Qu = ΣAh(9c) = (2.26)(9)(3,000) = 61,020 lb
- PassSupportworks Example 1: Qa = Qu / FOS = 61/2 = 30.5 kips (FOS 2)
- PassSupportworks Example 1: Torque Correlation, T = Qu/Kt = 60,000/9 = 6,667 ft·lb (Kt = 9 ft⁻¹)
- PassSupportworks Example 2: Nq = 1 + 0.56(12φ)^(φ/54) = 42.6 at φ = 38° and 15.7 at φ = 30°
- PassSupportworks Example 2: net plate areas 10/12 in. on a 3.5 in. shaft = 0.48/0.72 ft²
- PassSupportworks Example 2: Qu = ΣAh(q′Nq) = 84,310 lb (q′12" = 1,595, q′10" = 1,731 psf, φ = 38°)
- PassSupportworks Example 2: loose sand above the 12 in. plate (φ = 30°) gives Qu = 53,420 lb
- PassSupportworks Example 2: T = Qu/Kt = 80,000/7 = 11,428 ft·lb (Kt = 7 ft⁻¹, 3.5 in. shaft)
- PassTMG: Nq at φ = 34° is 22.0 (Perko 0.5(12φ)^(φ/54)) and 25.7 (1 + 0.56(12φ)^(φ/54))
- PassTMG: net areas on a 2⅞ in. shaft, 12 in. = 0.740 and 10 in. = 0.500 ft²
- PassTMG: net areas on a 3½ in. shaft, 10/12/14 in. = 0.479/0.719/1.002 ft²
- PassTMG attempt one (2⅞ in. shaft, φ = 34°, Nq = 25.7): plate loads 20,122 and 15,898 lb; Qult = 36.0 kip
- PassTMG attempt one with Nq = 22.0 (Perko): Qult = 30.8 kip
- PassTMG attempt two (3½ in. shaft, 10/12/14 in.): plate loads 19,606 / 26,686 / 32,613 lb; Qult = 78.9 kip
- PassTMG attempt two with Nq = 22.0 (Perko): Qult = 67.5 kip
- PassTMG attempt three (four plates 10/12/14/14 in.): plate loads 21,072 / 28,887 / 35,683 / 30,310 lb; Qult = 116.0 kip
- PassTMG attempt three with Nq = 22.0 (Perko): Qult = 99.3 kip
- PassTMG: required torque T = 80,000/Kt → 8,889 ft·lb at Kt = 9 ft⁻¹ (attempt one) and 11,429 ft·lb at Kt = 7 ft⁻¹
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hetenyi-beam-web-validationBeam on an elastic foundation — validated against **Hetényi (1946)**, *Beams on Elastic Foundation*, University of Michigan Press, and **Bowles (1997)**, *Foundation Analysis and Design* 5th ed., McGraw-Hill.23 passing
Analyses validated: hetenyi-beam
- PassHetényi Eq 8 — the characteristic parameter λ and the derived rigidities
- PassHetényi Eq 17 — infinite beam, concentrated load: the three closed-form maxima
- PassHetényi Eq 17 — the full deflection and moment PROFILE, not just the peaks
- PassHetényi — an applied MOMENT on an infinite beam (Eq 23)
- PassHetényi — superposition holds (the solution is linear)
- PassHetényi — the λL rigidity bands
- PassHetényi — a long finite beam converges on the infinite-beam solution
- PassHetényi §18 — λ and λl (p. 47)
- PassHetényi §18 — the P load on the infinite beam at A and B (Eq 5 c-d, p. 47)
- PassHetényi §18 — the UDL on the infinite beam at A, B (Eqs 8, 9) and C (Eq 7) — the Simpson-defect regression
- PassHetényi §18 — P + q on the infinite beam: the printed totals at A and B (p. 47)
- PassHetényi §18 — the infinite-beam deflections at A, C, B (table a, p. 48)
- PassHetényi §18 — the FINITE free-ended beam: deflections, soil pressure, M and Q at C (pp. 48-49)
- PassHetényi §12 Example 1 — equal forces at x = π/2λ reduce the maximum moment (0.7921, 0.5842, 0.7489)
- PassHetényi §12 Example 4 — reinforcing ring on a long tube: bending stress is 82 % above the hoop stress (p. 35-36)
- PassHetényi §6 — concentrated moment: y and M reverse to the left, Q does not; M jumps by M₀ across the load
- PassHetényi — a pure couple on a FINITE free beam carries no net soil force and balances its own moment
- PassHetényi — an applied moment AT a free end: M just inside the end equals the applied moment (free-end condition)
- PassHetényi Table I — A, B, C, D at λx = 0.70, 0.89, 1.00, 1.25, 1.50 (printed to 4 decimals)
- PassBowles Example 9-6 — an independent solver WITH the printed doubled end springs reproduces the printed output
- PassBowles Example 9-6 — global equilibrium: the engine's soil reaction sums to the applied 3375 kN (printed 3374.71 vs 3375.00)
- PassBowles Example 9-6 — the engine against the printed deflections, pressures and moments (model-limited band)
- PassBowles Example 9-6 — WHY the engine differs: against the same solver without the end-spring doubling it agrees
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
lateral-pile-group-published-web-validationPublished-answer validation for the lateral pile-GROUP p-multiplier engine (`lateral-pile-group.ts`).9 passing
Analyses validated: lateral-pile-group
- PassFHWA Table 14-2, 3D c-c: lead 0.7, 2nd 0.5, 3rd+ 0.35
- PassFHWA Table 14-2, 4D c-c: lead 0.85, 2nd 0.65, 3rd+ 0.5
- PassFHWA Table 14-2, 5D c-c: lead 1.0, 2nd 0.85, 3rd+ 0.7
- PassFHWA Table 14-2, ≥6D c-c: no group reduction in any row (1.0, 1.0, 1.0)
- PassAASHTO (2007) Table 10.7.2.4-1, 3B spacing: Row 1 0.7, Row 2 0.5, Row 3 and higher 0.35
- PassAASHTO (2007) Table 10.7.2.4-1, 5B spacing: Row 1 1.0, Row 2 0.85, Row 3 and higher 0.7
- PassAASHTO Table 10.7.2.4-1 "Row 3 and higher": a 5th row still takes the row-3 value
- PassFHWA §14.6.1 (2×2 group, s = 3D): weighted average Pm = [2(0.7)+2(0.5)]/4 = 0.6
- PassFHWA §14.6.2 (2×3 group, three rows of two shafts, s = 3D): weighted average Pm = 0.52
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
lateral-pile-group-web-validationFormula-fidelity validation against Brown (1987) Table 14-2 (as tabulated in FHWA-NHI-10-016 Drilled Shafts Manual §14.5.1), IDENTICAL to AASHTO LRFD Bridge Design Table 10.7.2.4-1 -- the published p-multiplier (Pm) values by row and spaci…12 passing
Analyses validated: lateral-pile-group
- Pass[1-12] all 12 published table anchors (AASHTO LRFD Table 10.7.2.4-1 / Brown Table 14-2): rows 1-3 at spacing 3D/4D/5D/6D
- Pass[13-14] linear interpolation between anchors matches exactly: row1 at 3.5D = 0.775, row2 at 4.5D = 0.75
- Pass[15] spacing below 3D holds the 3D anchor (extrapolation is unsupported by the data, per the engine's own documented policy)
- Pass[16] spacing at or above 6D gives Pm=1.0 for every row (no shadowing at wide spacing)
- Pass[17] row 4+ shares the row-3+ column exactly, per the table's own "3rd+" grouping
- Pass[18-19] side-by-side factor matches the exact Reese & Van Impe (2011) closed-form 0.64.(s/D)^0.34: s/D=3 -> 0.929825, s/D=2 -> 0.810084
- Pass[20] side-by-side factor caps at 1.0 for wide spacing
- Pass[21] side-by-side factor defaults to 1.0 (no reduction) when spacing is not supplied, per the documented policy that it is second-order and off by default
- Pass[22] the leading row (highest Pm) always carries at least as much load per pile as trailing rows, at the common cap deflection
- Pass[23] group efficiency is < 1 (shadowing reduces total capacity relative to isolated piles) and equals group load / (n . isolated load at the same deflection) exactly
- Pass[24] a manual p_multipliers override is used verbatim instead of the auto AASHTO table
- Pass[25] invalid inputs (zero diameter, spacing, or load) are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
lateral-pile-matlock-reese-web-validationWeb-benchmark validation for the p-y lateral-pile FDM solver against the EXACT Matlock & Reese (1960) nondimensional solution — the closed-form analytical benchmark that underlies COM624 / a p-y beam-column (Reese) solver.5 passing
Analyses validated: lateral-pile
- Passfree-head lateral load → Matlock-Reese Ay = 2.435 and Am = 0.772
- Passfree-head applied moment → Matlock-Reese By = 1.623
- Passfixed-head lateral load → 0.930·P·T³/EI deflection and −0.930·P·T moment
- Passresponse is linear in load and follows the T-scaling law
- Passthe linear_subgrade p-y is exactly p = k·z·y (no cap, elastic reference)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
lateral-pile-pdelta-web-validationValidation for the axial P-Δ (beam-column) term added to the laterally-loaded pile solver (`lateral-pile.ts`).6 passing
Analyses validated: lateral-pile
- PassP = 0 (and axial omitted) are byte-identical — regression guard
- PassAxial compression amplifies head deflection and max moment (P-Δ)
- PassAmplification grows monotonically and accelerates toward buckling
- PassA very large axial load drives buckling/overload (no finite equilibrium)
- PassFixed-head pile also shows axial amplification
- PassAmplification obeys the Timoshenko-Gere magnification law Af = 1/(1−P/Pcr), with Pcr ≈ Davisson-Robinson
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
micropile-web-validationPublished-value validation for micropile capacity (`micropile.ts`, `computeMicropile`): structural allowable loads of the composite cased/uncased section and the grout-to-ground bond.13 passing
Analyses validated: micropile
- PassFHWA NHI-05-039 Eq. 5-1, Fig. 5-2 example: Pc-allowable = 276 kips
- PassFHWA Appendix D Step 3: cased length Pt-allowable = 0.55 Fy (Abar + Acasing) = 620 kN
- PassFHWA Appendix D Step 3: cased length Pc-allowable = 0.4 f′c Agrout + 0.47 Fy (Abar + Acasing) = 671 kN
- PassFHWA Appendix D Step 4: uncased length Pt-allowable = 0.55 Fy-bar Abar = 415 kN
- PassFHWA Appendix D Step 4: uncased length Pc-allowable = 730 kN
- PassFHWA Appendix D Step 5 (Eq. 5-9): PG-allowable = (265/2.0)(3.14)(0.191)(7.5) = 596 kN at Lb = 7.5 m
- PassFHWA Appendix D Step 5 (Eq. 5-10): the required bond length Lb = 7.48 m carries PG-allowable = 595 kN
- PassFHWA Appendix D Step 6: the 595 kN design load is satisfied (671 / 730 / 596 kN allowables all ≥ 595) — "pile axial design is OK"
- PassFHWA Chapter 6 Eq. 6-1: Pult = 66 kPa × 10 m × π × 0.229 m = 475 kN
- PassFHWA Chapter 6 §6.7.4: Lbelow = 475/(515 π 0.229) × 2.0 = 2.6 m provides the 475 kN
- PassFHWA Appendix E (Eq. 5-6): Pc-allowable = 0.4 (27.6)(0.0218) + 0.47 (552)(0.00863) = 2,479 kN
- PassFHWA Appendix E: Fa = 0.47 Fy = 259.44 MPa is the steel compression stress in Pc-allowable
- PassFHWA Appendix E: Fb-type allowable 0.55 Fy = 303.6 MPa is the steel tension stress in Pt-allowable
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-axial-load-transfer-web-validationrecords a differenceAxial load-transfer (t-z / q-w) engine (`pile-axial-load-transfer.ts`) compared with the PUBLISHED numbers that could actually be opened and that map onto something this engine computes.18 passing
Analyses validated: pile-axial-load-transfer
- Pass[1] Das Table 4.2: N_q = 6.40 at φ' = 20°
- Pass[1] Das Table 4.2: N_q = 10.66 at φ' = 25°
- Pass[1] Das Table 4.2: N_q = 14.72 at φ' = 28°
- Pass[1] Das Table 4.2: N_q = 18.40 at φ' = 30°
- Pass[1] Das Table 4.2: N_q = 23.18 at φ' = 32°
- Pass[1] Das Table 4.2: N_q = 33.30 at φ' = 35°
- Pass[1] Das Table 4.2: N_q = 48.93 at φ' = 38°
- Pass[1] Das Table 4.2: N_q = 64.20 at φ' = 40°
- Pass[1] Das Table 4.2: N_q = 85.38 at φ' = 42°
- Pass[1] Das Table 4.2: N_q = 134.88 at φ' = 45°
- Pass[2] Bowles Table 4-4: N_q = 6.4 at φ = 20°
- Pass[2] Bowles Table 4-4: N_q = 10.7 at φ = 25°
- Pass[2] Bowles Table 4-4: N_q = 18.4 at φ = 30°
- Pass[2] Bowles Table 4-4: N_q = 29.4 at φ = 34°
- Pass[2] Bowles Table 4-4: N_q = 37.7 at φ = 36°
- Pass[2] Bowles Table 4-4: N_q = 64.1 at φ = 40°
- Pass[3] Varghese Ex 13.2 (Skempton): N_c = 9 for a deep clay base
- Pass[4] Mittal Ex 3.1 (Eq 3.12): N_c = 9.0
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-buckling-web-validationrecords a differencePartially-embedded pile buckling (`pile-buckling.ts`, Davisson–Robinson equivalent cantilever) checked against PUBLISHED numbers.10 passing
Analyses validated: pile-buckling
- Pass[1] IS 800 Table 11: fixed-free column has effective length 2.0 L
- Pass[2] IS 800 Table 11: pinned-pinned column has effective length 1.0 L
- Pass[3] IS 800 Table 11: translation held, fixed one end and pinned at the other has effective length 0.8 L
- Pass[4] IS 800 Table 11: both ends fixed and translation held has effective length 0.65 L
- Pass[5] Tomlinson Eq 6.51 and NAVFAC DM 7.02: for a linearly increasing modulus z_f = 1.8 T
- Pass[6] Tomlinson Eq 6.50 and NAVFAC DM 7.02: for a constant modulus z_f = 1.4 R
- Pass[7] Bowles Ex 16-14: 7.00 m free-standing part, EI = 200 000 MPa × 0.379×10⁻⁴ m⁴, fixed at the ground line (k = 2) → Euler load 381.7 kN
- Pass[8] Varghese Ex 13.3: R = [EI/(K_h B)]^¼ = 0.546 m for EI = 0.4 MN·m², K_h = 15 MN/m³, B = 0.3 m
- Pass[9] Varghese Ex 13.4: T = (EI/n_h)^⅕ = 1.32 m for EI = 40×10⁶ N·m², n_h = 10×10⁶ N/m³
- Pass[10] Mittal: T = 1.63 m for E = 28 500 MPa, I = 0.0031 m⁴ (as printed), n_h = 7750 kN/m³
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-capacity-web-validationWEB-BENCHMARK validation for the axial pile-capacity engine (the release rules mandatory ≥20 cited-value gate).7 passing
Analyses validated: pile-capacity
- Passpile web-validation: Tomlinson / API adhesion factor α (PDCP curve)
- Passpile web-validation: IS 2911-1 Annex B-2 Fig. 2 α (chart read-off ±0.02)
- Passpile web-validation: Skempton Nc = 9 base resistance in clay (qb = 9·su)
- Passpile web-validation: Reissner Nq at pile tip in sand (capped at Lc=15D)
- Passpile web-validation: critical depth 15·D at φ ≤ 30° → 20·D at φ ≥ 40° (IS 2911-1 Annex B-1 Note 5)
- Passpile web-validation: full Qult integration — hand-verified from cited factors
- Passpile web-validation: INTERNATIONAL design paths — AASHTO LRFD + EC7 partial factors
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-capacity-worked-examples-web-validationpile-capacity — FULL WORKED EXAMPLES (the ≥20-value gate).28 passing
Analyses validated: pile-capacity
- Pass[DAS] Ex 9.2 Meyerhof point resistance in clay Qp = 9·cu·Ap = 132.9 kN
- Pass[DAS] Ex 9.7 α method (Table 9.10 α) → Qs = 1050 kN
- Pass[DAS] Ex 9.7 α method, layer 1 shaft = 93.7 kN
- Pass[DAS] Ex 9.7 α method, layer 2 shaft = 297.5 kN
- Pass[DAS] Ex 9.7 α method, layer 3 shaft = 659.1 kN
- Pass[DAS] Ex 9.5 sand shaft, K = 1.3, δ = 0.8φ, L′ = 15D → Qs = 2094.43 kN on a 1.628 m perimeter
- Pass[BOW] Ex 16-3 very soft clay, single α = 1.05 → Qs = 284.9 kN
- Pass[BOW] Ex 16-3 point Ppu = 9·su·Ap = 7.7 kN
- Pass[BOW] Ex 16-4 upper soft clay (α 0.98): Qs,1 = 256 kN
- Pass[BOW] Ex 16-4 medium clay (α 0.88): 70.2 kN per metre
- Pass[BOW] Ex 16-4 point Qp = 9·su·Ap = 82 kN
- Pass[DUB] A.8.2 characteristic base Rb;k = 9·cu·Ab = 386 kN
- Pass[DUB] A.8.2 characteristic shaft Rs;k = 153 kN per metre (α 0.4)
- Pass[DUB] A.8.2 EC7_DA1_C1: R_c;d = 221 + 87.4·Ls at Ls = 8 m
- Pass[DUB] A.8.2 EC7_DA1_C1: R_c;d = 221 + 87.4·Ls at Ls = 16 m
- Pass[DUB] A.8.2 EC7_DA1_C2: R_c;d = 170 + 67.3·Ls at Ls = 8 m
- Pass[DUB] A.8.2 EC7_DA1_C2: R_c;d = 170 + 67.3·Ls at Ls = 16 m
- Pass[DUB] A.8.2 EC7_DA2: R_c;d = 201 + 79.5·Ls at Ls = 8 m
- Pass[DUB] A.8.2 EC7_DA2: R_c;d = 201 + 79.5·Ls at Ls = 16 m
- Pass[DUB] A.8.2 EC7_DA3: R_c;d = 158 + 62.3·Ls at Ls = 8 m
- Pass[DUB] A.8.2 EC7_DA3: R_c;d = 158 + 62.3·Ls at Ls = 16 m
- Pass[EN] EN Table A.6 driven R4 (DA1-C2): γb 1.3, γs 1.3
- Pass[EN] EN Table A.7 bored R1 (DA1-C1): γb 1.25, γs 1.0
- Pass[EN] EN Table A.7 bored R4 (DA1-C2): γb 1.6, γs 1.3
- Pass[AASHTO] Table 10.5.5.2.3-1 driven pile in clay, α-method: φ = 0.35
- Pass[AASHTO] Table 10.5.5.2.3-1 driven pile in sand, Nordlund/Thurman: φ = 0.45
- Pass[AASHTO] Table 10.5.5.2.4-1 drilled shaft in clay: side 0.45, tip 0.40
- Pass[AASHTO] Table 10.5.5.2.4-1 drilled shaft in sand: side 0.55, tip 0.50
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-downdrag-web-validationPILE DOWNDRAG (negative skin friction) — web-validation benchmark.15 passing
Analyses validated: pile-downdrag
- PassDas Ex 9.19 — clay fill over granular, Eq (9.123): 6 published values
- PassDas Ex 9.19 — Qn scales as Hf², which is what Eq (9.123) asserts
- PassDas Ex 9.20 — neutral depth Eq (9.124) and drag Eq (9.126): 8 published values
- PassDas Ex 9.20 — the closed-form root satisfies Eq (9.124) AS PRINTED, not just our rearrangement
- PassE-54 — end-bearing vs floating is a factor of two on the drag force
- PassOslo harbour test pile — reproduces the published 2348 kN and lands within 6.1 % of the measured 2500 kN
- PassE-55 (unsafe) — α banded by s_u gives 0.4 where FHWA §13.6.4 requires 1.0: 2.5x under-predicted drag
- PassE-53 (conservative) — β interpolated on φ′ is 2.04x the K₀ form the sources use
- Passthe general summation and the closed form agree on the Oslo clay layer
- PassAASHTO LRFD downdrag load factors are 1.25 (max) and 0.35 (min)
- PassLRFD check counts only the side resistance BELOW the neutral plane
- Passvesic_bowles refuses to infer the idealisation from a layer stack
- Passvesic_bowles validates its own envelope
- PassEq (9.124) always places the neutral plane between 50 % and 70.7 % of the penetrated clay
- Passmethod labels cover every method, so no selector can render blank
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-group-is2911-web-validationPile group capacity — validated against **IS 2911 (Part 1/Sec 1):2010** (driven cast in-situ concrete piles) and the published efficiency formulae it refers to without mandating.6 passing
Analyses validated: pile-group
- PassConverse-Labarre efficiency — 10 published configurations
- PassIS 2911 Cl 6.7.2 — group capacity never exceeds N × single-pile capacity
- PassIS 2911 Cl 6.7.3 — the block check, with Tomlinson §10.4 as the equation form
- Passthe block check is applied to cohesive soil and skipped for cohesionless (Cl 6.7.2)
- PassFeld and Seiler-Keeney are offered as alternatives, and all three are bounded in (0, 1]
- Passthe references cite Cl 6.7.3, not the non-existent Annex F
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-group-settlement-web-validationrecords a differencePile-group settlement engine (`pile-group-settlement.ts`, Randolph–Wroth interaction factors) compared with what could actually be opened.4 passing
Analyses validated: pile-group-settlement
- Pass[1] Kouretzis Ex 6.10 (Poulos–Mattes chart): α = 0.42 at s/D = 5
- Pass[2] Kouretzis Ex 6.10: α = 0.35 at s/D = 7.07
- Pass[3] Kouretzis Ex 6.10: α = 0.27 at s/D = 10
- Pass[4] Kouretzis Ex 6.10: α = 0.25 at s/D = 11.2
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-group-worked-examples-web-validationpile-group — PUBLISHED WORKED EXAMPLES (deep review 14, 2026-10-03).11 passing
Analyses validated: pile-group
- Pass[BW1] Bowles Ex 18-1: Converse-Labarre 5 × 3, D 400 mm, s 1000 mm → E_g = 0.64
- Pass[BW2] Bowles Ex 18-2: 15 × 486 kN = 7290 kN governs (η = 1, block does not govern)
- Pass[DS] Das Ex 9.21: block 4313 kip, ΣQu 3141.9 kip governs
- Pass[VG] Varghese Ex 13.1: 9 × 396 = 3564 kN, Q_safe = 3564/2.5 = 1426 kN; [IS] default FoS 2.5
- Pass[FD] Feld 1/16 rule: 3 × 3 → 0.722, 2 × 2 → 0.813
- Pass[SV] Structville 3 × 3 rigid cap: concentric 543.14 kN; eccentric −19.36 … 1105.64 kN
- Pass[VH] vulcanhammer Ex 3.1: 12 piles at 0.9 m, Q 2600 kN, M 520 / 390 kN·m → max 329, min 105 kN
- Passa working reaction is checked against Qu/FoS, not against the ultimate Qu
- PassFoS below 1 is refused; below 2.5 is warned with the clause
- Passspacing warnings cite IS 2911-1 Cl 6.6 (2.5D end-bearing, 3D friction), not Cl 6.7
- Passnon-finite and impossible inputs are refused, never returned as η = NaN or an infinite group
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-head-stiffness-web-validationPile-head stiffness engine (`pile-head-stiffness.ts`) checked against PUBLISHED Matlock–Reese numbers.7 passing
Analyses validated: pile-head-stiffness
- Pass[1] PUBLISHED Das Table 9.15 (Z = 0): free-head deflection under a lateral load is A_x·Q·T³/EI with A_x = 2.435
- Pass[2] PUBLISHED Das Table 9.15 (Z = 0): free-head deflection under a head moment is B_x·M·T²/EI with B_x = 1.623
- Pass[3] PUBLISHED Das Example 9.14: HP 250×85 in n_h = 12 000 kN/m³ deflects 8 mm under Q_g = 53.59 kN (free head, M = 0)
- Pass[4] PUBLISHED Rocscience Example 1: the moment that holds the head against rotation is 271.1 kN·m (H = 200 kN)
- Pass[5] DERIVED K22 = (EI/T³)·|B_θ|/(A_x|B_θ| − B_x²) from the published coefficients
- Pass[6] DERIVED K33 = (EI/T)·A_x/(A_x|B_θ| − B_x²) from the published coefficients
- Pass[7] DERIVED |K23| = (EI/T²)·B_x/(A_x|B_θ| − B_x²) from the published coefficients
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-load-test-is2911p4-web-validationPile load test interpretation — validated against **IS 2911 (Part 4):2013**, *Code of Practice for Design and Construction of Pile Foundations, Part 4: Load Test on Piles* (2nd revision).6 passing
Analyses validated: pile-load-test
- PassIS 2911-4 Cl 7.1.5(a) — piles ≤ 600 mm use the 12 mm displacement criterion
- PassIS 2911-4 Cl 7.1.5(b) — piles > 600 mm use min(18 mm, 2 % of D) [E-33]
- PassIS 2911-4 Cl 7.1.5 criterion (2) — 50 % of the load at 10 % of the pile diameter
- Passthe "unless otherwise required in a given case" override is honoured and disclosed
- Passa test that never reaches the criteria must refuse to set a safe load
- Passmonotonicity and bounds across the criteria
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-load-transfer-web-validationValidation for API axial load-transfer curves (`pile-load-transfer.ts`).4 passing
Analyses validated: not attributed by the manifest
- PassAPI clay t-z table points (RP2GEO)
- PassAPI clay t-z interpolates monotonically to the peak
- PassAPI q-z tip table points (RP2GEO), peak at z/D=0.10
- PassAPI sand t-z: linear to peak at 0.1 in then plateau
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-raft-web-validationWeb-benchmark validation for `pile-raft` — the Poulos "PDR" piled-raft stiffness method.10 passing
Analyses validated: pile-raft
- Passthe component stiffnesses follow their published definitions
- Passa negative Poulos denominator is refused rather than answered (neither the spurious K_pr nor a parallel spring)
- Passa well-conditioned case exercises the primary K_pr branch
- Passload is conserved and the pile fraction stays in [0, 1] across a wide sweep
- Passmore piles carry more load and settle less
- Passthe raft stiffness is Fleming Eq 5.33, k_r = E_s·√(BL)/[I(1 − ν²)]
- Passrelative stiffness K_r = E_c·I_b/(E_s·B³) classifies rigid / intermediate / flexible
- Passthickness and E_c without a soil modulus: refused, naming E_s (no hidden k_s default)
- Passpile utilisation is against the WORKING load and warns past the PDR limit
- Passinvalid inputs are refused with no numbers
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-section-mphi-web-validationrecords a differenceReinforced-concrete moment–curvature engine (`pile-section-mphi.ts`) checked against PUBLISHED numbers.11 passing
Analyses validated: pile-section-mphi
- Pass[1] the engine puts the bar centroid where Pincheira Ex 10.18.1 does: d1 = 2.64 in
- Pass[2] Pincheira Ex 10.18.1 Point 6 pure bending: Mn at Pn = 0.0 kip is 320.11 kip-ft
- Pass[2] Pincheira Ex 10.18.1 Point 5 εs = εy + 0.003 (tension-controlled limit): Mn at Pn = 29.5 kip is 328.13 kip-ft
- Pass[2] Pincheira Ex 10.18.1 Point 4 fs = fy (balanced, c = 10.28 in): Mn at Pn = 518.93 kip is 407.73 kip-ft
- Pass[2] Pincheira Ex 10.18.1 Point 3 fs = 0.5 fy: Mn at Pn = 856.27 kip is 375.24 kip-ft
- Pass[2] Pincheira Ex 10.18.1 Point 2 fs = 0: Mn at Pn = 1312.64 kip is 277.54 kip-ft
- Pass[4] FHWA-NHI-10-016 Fig 12-24: the 48-in shaft with 12 #11 bars reaches Mult = 1791 kip-ft
- Pass[5] FHWA-NHI-10-016 §12.3.3.3.4: I = π·d⁴/64 = 260,576 in⁴ for the 48-in shaft (gross section)
- Pass[6] FHWA-NHI-10-016 Appendix A: I = 4,169,220 in⁴ for the 96-in shaft
- Pass[7] Wang Ex 3.11.1 singly reinforced, As = 7.74 in² (max tension-controlled): Mn = 855 kip-ft
- Pass[8] Wang Ex 3.11.1 doubly reinforced, As = 9.42 in², A's = 1.81 in²: Mn = 1048 kip-ft
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-section-pm-interaction-ec2-web-validationEN 1992-1-1 code path of the P–M interaction engine (`pile-section-pm-interaction.ts`, `code: 'EN 1992-1-1'`) checked against PUBLISHED values.15 passing
Analyses validated: pile-section-pm-interaction
- PassConcrete Centre App. C Fig C4c (p.208), d2/h=0.15, ρ_s=0.2 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4c (p.208), d2/h=0.15, ρ_s=0.4 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4c (p.208), d2/h=0.15, ρ_s=0.6 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4c (p.208), d2/h=0.15, ρ_s=0.8 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4c (p.208), d2/h=0.15, ρ_s=1 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4d (p.208), d2/h=0.2, ρ_s=0.2 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4d (p.208), d2/h=0.2, ρ_s=0.4 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4d (p.208), d2/h=0.2, ρ_s=0.6 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4d (p.208), d2/h=0.2, ρ_s=0.8 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C Fig C4d (p.208), d2/h=0.2, ρ_s=1 — M/(bh²fck) at four N/(bhfck) levels
- PassConcrete Centre App. C charts supply 2×19 = 38 published values (≥ 20)
- PassConcrete Centre §5.1 (p.135): 300×300 C30/37, 4H25, d2=49 — MRd at NEd=1620 kN is 76.1 kN·m
- PassConcrete Centre §5.3 (p.146): 500×500 C50/50, 12H32, d2/h=0.20 — MRd at NEd=9000 kN is 356.3 kN·m
- PassConcrete Centre §5.4 (p.157): 350×350 C30/37, 4H32+4T25, d2/h=0.25 — MRd at NEd=1824.1 kN is 205.8 kN·m
- PassConcrete Centre §5.4 (p.157): 350×350 C30/37, 8T32, d2/h=0.25 — MRd at NEd=1824.1 kN is 240.5 kN·m
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-section-pm-interaction-is456-web-validationrecords a differenceIS 456 code path of the P–M interaction engine (`pile-section-pm-interaction.ts`, `code: 'IS 456'`) checked against PUBLISHED values.12 passing
Analyses validated: pile-section-pm-interaction
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.06 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.10 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.12 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.14 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.16 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.18 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.20 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.22 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 Chart 33 (p.118), p/fck = 0.25 — Mu/(fck·b·D²) at six Pu/(fck·b·D) levels
- PassSP 16:1980 chart-valve count — the Chart 33 contours supply 9×6 = 54 published values (≥ 20)
- PassSP 16:1980 Worked Example 6 (p.103): 450×450 M25 Fe415, Pu=2500 kN, Mu=200 kNm → p/fck=0.09 (As=4556 mm²), two sides
- PassSP 16:1980 Worked Example 7 (pp.103–104): Ø500 M20 Fe250, 8 bars, Pu=1600 kN, Mu=125 kNm → p/fck=0.087 (As=3416 mm²)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-section-pm-interaction-web-validationrecords a differenceP–M interaction engine (`pile-section-pm-interaction.ts`) checked against PUBLISHED numbers.15 passing
Analyses validated: pile-section-pm-interaction
- Pass[1] Pincheira §1.1: nominal axial strength at zero eccentricity P0 = 1902 kip
- Pass[2] Pincheira §7: maximum tension Pnt = fy·Ast = −609.60 kip
- Pass[3] Pincheira §1.3: maximum (allowable) factored axial strength φPn,max = 0.85·0.75·P0 = 1212.3 kip
- Pass[4] Pincheira §7: factored maximum tension φPnt = 0.90·609.60 = −548.64 kip
- Pass[5] FHWA-NHI-10-016 App. A: 96-in shaft, 40 #14, f'c 4 ksi, fy 60 ksi — "nominal crushing strength of 29,703 kips"
- Pass[6] Pincheira §6: pure bending Mn = 320.11 kip-ft
- Pass[7] Pincheira §5 εs = εy + 0.003: Mn(29.5 kip) = 328.13 kip-ft on the nominal envelope
- Pass[7] Pincheira §4 fs = fy: Mn(518.93 kip) = 407.73 kip-ft on the nominal envelope
- Pass[7] Pincheira §3 fs = 0.5 fy: Mn(856.27 kip) = 375.24 kip-ft on the nominal envelope
- Pass[7] Pincheira §2 fs = 0: Mn(1312.64 kip) = 277.54 kip-ft on the nominal envelope
- Pass[8] Pincheira Table 8 pure bending (φ = 0.90): φMn at φPn = 0 kip is 288.09 kip-ft
- Pass[8] Pincheira Table 8 tension-controlled limit: φMn at φPn = 26.55 kip is 295.31 kip-ft
- Pass[8] Pincheira Table 8 balanced (φ = 0.75): φMn at φPn = 389.2 kip is 305.8 kip-ft
- Pass[8] Pincheira Table 8 fs = 0.5 fy: φMn at φPn = 642.2 kip is 281.43 kip-ft
- Pass[8] Pincheira Table 8 fs = 0: φMn at φPn = 984.48 kip is 208.16 kip-ft
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-settlement-vesic-web-validationrecords a differenceSingle-pile working-load settlement — validated against **Vesić's own report**, not a secondary account of it.13 passing
Analyses validated: pile-settlement-vesic
- Pass[1-3] Das §9.17 worked example: the published load split is reproduced exactly
- Pass[4-5] the published elastic shortening — and the transposition in the printed answer
- Pass[6] the equivalent diameter really does reproduce the published section area
- Pass[7-8] HAND CHECK (not a published value) — Vesić Eq 44: C_s = (0.93 + 0.16·√(D/B))·C_p, with HIS D = depth and HIS B = width
- Pass[9-11] HAND CHECK (not a published value) — Vesić Eqs 42 and 43 term by term, and the total is a plain sum
- Pass[12-13] HAND CHECK (not a published value) — the proportionalities, which the closed forms make exact
- Pass[14-19] Vesić Table 6 (p.33) is the admissible span for C_p, and it is enforced
- Pass[20-22] ξ is bounded by Vesić p.32 — 0.1 to 0.67, not the narrower band once claimed here
- Pass[23-24] the SCOPE of Table 6 is declared on every run, not assumed
- Pass[25-27] the refusals are real, and a cleared box cannot produce a finite absurdity
- Pass[28-29] all of the load at the point, and all of it on the shaft, are both exact limits
- Pass[25] Canadian Foundation Engineering Manual Table 18.6 prints driven sand as 0.02–0.09; Vesić Table 6 and Das Table 9.14 print 0.02–0.04 — the engine accepts both
- Pass[26] CFEM Eq 18.21b: α_s = 0.5 for a uniform or parabolic skin-friction distribution and 0.67 for a linear one — both inside the engine's ξ span
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
py-curves-web-validationValidation for the p-y backbone library (`py-curves.ts`).35 passing
Analyses validated: py-curves
- PassMatlock 1970 — deep N_p caps at 9: p_u = 9·su·b
- PassMatlock 1970 — surface N_p = 3: p_u = 3·su·b
- PassMatlock 1970 — p(y50) = 0.5·p_u exactly
- PassMatlock 1970 — cube-root branch: p(y50/8) = 0.5·p_u·(1/8)^(1/3) = 0.25·p_u
- PassMatlock 1970 — monotonic non-decreasing to plateau
- PassWelch-Reese 1972 — p(y50) = 0.5·p_ult; deep p_ult = 9·su·b
- PassWelch-Reese 1972 — quarter-power branch: p(y50/16) = 0.5·pult·(1/16)^0.25 = 0.25·pult
- PassReese 1975 — deep wedge N_p caps at 11: p_u = 11·su·b
- PassReese 1975 — √ branch: p(y50) = 0.5·p_u
- PassReese 1974 sand — ultimate wedge p_s > 0 and increases with depth
- PassReese 1974 sand — backbone monotonic and reaches a plateau
- PassReese 1974 sand — initial branch stiffness = k·z near origin
- PassAPI sand — p → A·p_u as y→∞ (A static = max(0.9, 3−0.8z/b))
- PassAPI sand — initial slope dp/dy|₀ = k·z (tanh′(0)=1)
- PassAPI sand — static factor A ≥ 0.9 always (deep) and cyclic = 0.9
- PassRollins 2005 — exact anchor: z=2 m, b=1 m, y=100 mm ⇒ p = 44.914 kN/m
- PassRollins 2005 — exact anchor: z=3 m, b=0.6 m, y=50 mm ⇒ p = 17.942 kN/m
- PassRollins 2005 — displacement capped at 150 mm (p(200)=p(150))
- PassRollins 2005 — diameter clamped to [0.3, 2.6] m
- PassRollins 2005 — concave-up at shallow depth (C>1 ⇒ p(2y)>2·p(y))
- PassFranke-Rollins 2013 — hybrid = min(p_clay, p_liq)
- PassReese-Nyman 1978 — α_r = 1−(2/3)·RQD and shallow p_ur plateau
- PassReese-Nyman 1978 — deep p_ur = 5.2·α_r·qu·b
- PassReese-Nyman 1978 — RQD=100 ⇒ α_r = 1/3
- PassSimpson-Brown 2003 — Piedmont plateau past y/b = 0.0375
- PassSimpson-Brown 2003 — Piedmont initial linear branch p = b·y·E_si for y/b<0.001
- PassPY_FAMILIES catalogue lists 11 families, each with a citation
- PassJohnson 2006 loess — p_u = 0.409·q_c·b, initial slope E_i = p_u/y_ref, plateau→p_u
- PasspyBackbone dispatch matches direct calls (soft clay + liquefied)
- PasspyBackboneCurve returns monotone-y grid starting at (0,0)
- PassAPI RP2A sand — plateau p_u matches the published C1/C2/C3 chart (φ=30/35/40°)
- PassMatlock 1970 — full normalized backbone p/p_u = 0.5·(y/y50)^(1/3)
- PassWelch-Reese 1972 — full normalized backbone p/p_ult = 0.5·(y/y50)^0.25
- PassReese-Nyman 1978 weak rock — p/p_ur = 0.5·(y/y_rm)^0.25 on the power branch
- PassRollins 2005 — further exact liquefied-sand anchors (hand-computed)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
settlement-seepage-pile-web-validationWeb-benchmark validation for ELEVEN settlement, seepage/earth-pressure and lateral-pile runner engines.11 passing
Analyses validated: basal-heave, broms-lateral-pile, burland-burbidge, elastic-settlement, flow-net-seepage, infinite-slope, is8009-settlement, retaining-wall, settlement, skempton-bjerrum
- Passelastic-settlement reproduces the Steinbrenner F1/F2 factors and Bowles settlement
- Passis8009-settlement obeys the IS 8009 structural identities
- Passcv-oedometer uses the published T50 and T90 time factors
- Passskempton-bjerrum applies μ = A + α(1 − A) from Skempton & Bjerrum (1957)
- Passburland-burbidge reproduces the 1985 ICE paper expressions
- Passflow-net-seepage computes q = k·h·N_f/N_d (Terzaghi & Peck)
- Passretaining-wall reproduces Rankine thrust and wall statics exactly
- Passinfinite-slope reproduces the dry, seepage-parallel and r_u forms
- Passbasal-heave reproduces both methods and never publishes an unreconcilable FoS
- Passpile-settlement-vesic reproduces the Vesic (1977) three components
- Passbroms-lateral-pile solves the Broms (1964) long-pile equations in clay and sand
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
wave-equation-driving-web-validationWEB-BENCHMARK validation for the wave-equation pile-driving engine (Smith 1960) — now with the DIESEL variable-stroke thermodynamics and RESIDUAL-STRESS ANALYSIS that close the GRLWEAP-parity gap.37 passing
Analyses validated: wave-equation-driving
- PassWEAP 1: Vulcan-08 impact velocity = 3.61 m/s (matches WEAP87 11.84 ft/s exactly)
- PassWEAP 2: v0 scales as √(energy)
- PassWEAP 3: v0 scales as 1/√(ram weight)
- PassWEAP 4: hammer_model overrides ram/energy/η (Delmag D30)
- PassWEAP 5: custom (no model) keeps user-entered ram/energy
- PassWEAP 6: the library exposes ≥5 inspectable hammers (vs GRLWEAP closed register)
- PassWEAP 7: steel allowable = 0.90·f_y (default f_y 350 MPa ⇒ 315 MPa)
- PassWEAP 8: steel allowable tracks the entered f_y
- PassWEAP 9: prestressed concrete comp = 0.85·f′c − f_pe (35, 5 MPa ⇒ 24.75 MPa)
- PassWEAP 10: prestressed concrete tension = f_pe + 0.25√f′c ⇒ 6.48 MPa
- PassWEAP 11: timber allowable = 3× design stress
- PassWEAP 12: bearing graph blow count is MONOTONE increasing in Rᵤ
- PassWEAP 13: higher Rᵤ ⇒ harder driving (more blows/m) than lower Rᵤ
- PassWEAP 14: higher Rᵤ ⇒ smaller permanent set
- PassWEAP 15: free-end reflection ⇒ tensile stress appears (esp. at low resistance)
- PassWEAP 16: compressive driving stress is significant (of order the impact stress)
- PassWEAP 17: refusal — very high Rᵤ ⇒ ≥800 blows/m or REFUSAL verdict
- PassWEAP 18: overstress — tiny allowable ⇒ OVERSTRESS + stress_ok false
- PassWEAP 19: a workable case ⇒ DRIVABLE/hard + stress_ok true
- PassWEAP 20: stress utilisation = max(comp,tens)/allowable ·100
- PassWEAP 21: WEAP87 order-of-magnitude — 400-kip (1779 kN) blow count in a plausible band
- PassWEAP 22: transferred energy (ENTHRU) is positive and below the rated energy
- PassWEAP 23: blows/250mm = blows/m ÷ 4
- PassWEAP 24: invalid input ⇒ errors, no crash
- PassWEAP 25: Delmag diesel uses the variable-stroke model (diesel_model = true)
- PassWEAP 26: diesel stroke RISES with driving resistance (GRLWEAP behaviour)
- PassWEAP 27: diesel energy per blow RISES with resistance and is ≤ rated at refusal cap
- PassWEAP 28: diesel stroke approaches the rated stroke at refusal (calibration target)
- PassWEAP 29: an external-combustion hammer (Vulcan-08) holds a FIXED stroke
- PassWEAP 30: bearing graph carries the (variable, for diesel) stroke per Rᵤ
- PassWEAP 31: RSA runs, converges to a steady set, and labels itself
- PassWEAP 32: RSA vs standard differ modestly (residual pre-stress effect), same order
- PassWEAP 33: DIESEL transfer efficiency ≈ GRL measured 39% (band 29–49%, CoV 26%)
- PassWEAP 34: single-acting AIR/STEAM efficiency ≈ GRL measured 56% (band 43–69%)
- PassWEAP 35: HYDRAULIC efficiency ≈ GRL measured 69% (band 52–86%)
- PassWEAP 36: transfer_efficiency_pct = 100·ENTHRU/rated (self-consistent)
- PassWEAP 37: diesel refusal stroke ≈ 95% of rated (GRLWEAP §B2 P_max calibration)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Tunnels and underground works
9 finite-element rows (3 deviations, 1 recorded) · 0 closed-form problems · 9 validation suites
Finite-element solver registry
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
plastic radius around the unsupported circular opening (R = 2 m, σ0 = 15 MPa, GSI 50, mi 10, σci 30 MPa) k5b-plaxis-verif-hoek-brown-tunnel | default policy (strict, then the PLAXIS criterion with the initial stiffness — D124 + D684): (λ: 1; Rpl m: 3.821; elast… | 3.794m | +0.71 % | Ours default policy (strict, then the PLAXIS … mPublished 3.794 m+0.71 % | Pass | |
| ||||||
worst relative radial-displacement error on both faces of a thick cylinder loaded by a normal-pressure line load `pn` on its curved (polyline) inner face k5d1-lame-normal-pressure · Self-check | 0.0008874 | 0.002 | — | Ours 0.0008874Published 0.002— | Pass | |
| ||||||
radius change of a bonded elastic lining under a line contraction C_ref = 0.5 % k5d1-contraction-ring · Self-check | -0.00178701m | -0.00178571m | +0.07 % | Ours -0.00178701 mPublished -0.00178571 m+0.07 % | Pass | |
| ||||||
plastic radius around the circular opening supported by a 2500 kPa normal pressure k5d1-hb-tunnel-case2 | 2.598m | 2.582m | +0.62 % | Ours 2.598 mPublished 2.582 m+0.62 % | Pass | |
| ||||||
NATM tunnel, β-method (60 % / 100 %) in two excavation stages: crown settlement, lining forces k5d1-plaxis-2d-tut6-natm | crown uy phase 1..4 mm: [-7.45, -8.65, -9.17, -9.11]; crest (−7, 35) uy phase 4 mm: -19.77; liningTop M max/min kNm/m:… | — | — | Ours crown uy phase 1..4 mm: [-7.45, -8.65, -…Published —— | Recorded, no published value | |
| ||||||
building tilt at the end of phase 5 (lining), displacements from phase 2 on: (uy(15, 3) − uy(5, 3)) / 10 m k5d1-plaxis-2d-tut5-building-tilt | 0.1834% | 0.168% | +9.17 % | Ours 0.1834 %Published 0.168 %+9.17 % | Deviation | |
| ||||||
applied plate contraction strain of the TBM (C_ref/2) k5d1-plaxis-2d-tut5-contraction | 0.0025 | 0.0025 | 0.00 % | Ours 0.0025Published 0.00250.00 % | Pass | |
| ||||||
maximum settlement at ground level after phase 5 (PLAXIS: horizontal cross-section at z = 1.95 m; ours: surface z = 2 m) tunnel-s1-plaxis3d-tut5-ground-settlement | 1.8549cm | 1.9cm | −2.37 % | Ours 1.8549 cmPublished 1.9 cm−2.37 % | Deviation | |
| ||||||
maximum vertical displacement after phase 5 (Fig 5-34 caption) tunnel-s1-plaxis3d-tut5-max-uz | 3.4275cm | 3.1cm | +10.6 % | Ours 3.4275 cmPublished 3.1 cm+10.6 % | Deviation | |
| ||||||
Cited validation suites
shotcrete-age-stiffness-web-validationrecords a differenceWeb-validation for `shotcrete-age-stiffness.ts` — the time-dependent E(t) and fcu(t) of young shotcrete used in NATM / SEM lining modelling.18 passing
Analyses validated: shotcrete-age-stiffness
- PassCEB-FIP s-parameters: s_stiff and s_strength from the printed equations (exact)
- PassCEB-FIP law reproduces the 1-day and 28-day anchors exactly
- PassCEB-FIP E(t) and fcu(t) are the exact printed closed form (Neuner Eqs. 5-8)
- PassCEB-FIP vs measured Neuner series: documented model deviation (FINDING-2)
- PassCEB-FIP very-early-age lower limit: fcu ≥ 0.005·fcu,28 (PLAXIS MM §14.3.1)
- PassCEB-FIP stiffness is monotonic and constant beyond t_hydr
- PassEN 14487-1 J2 class tabulated strengths at the printed ages (exact)
- PassEN 14487-1 J1/J3 classes at 12 h and 24 h (printed Table 14–1)
- PassEN 14487-1 → Oluokun bridge after 24 h reaches fcu,28 at 28 d
- PassOluokun fc(t) = αc·e^(−b_c/t) against the printed equation (exact)
- PassRound-length helper: age at full load = (d + 2RT)/Lr × tr (definition)
- PassRound-length helper warns when the ring is very young at full load (< 8 h)
- Passwrapper: input validation and monotonicity warnings
- PassSmaniotto 2022 §4.1: strength at 1 d is the STATED "50 %" of the 28-d strength (23.8 / 47.6 MPa) — engine anchors reproduce it
- PassSmaniotto 2022 Table 5 / A.3: Young's modulus anchors 18 200 MPa (1 d) and 28 700 MPa (28 d) reproduced by the CEB-FIP law
- PassSmaniotto 2022 Table A.3: Meschke-Kropik-Mang E(t), anchored at 1 d / 28 d, tracks the measured 2, 7, 14 d means within 2 SD
- PassSmaniotto 2022 Tables A.1/A.3 — FINDING: the two-anchor CEB-FIP law over-predicts the measured intermediate-age strength and stiffness by more than 2 SD at 2 d and 7 d
- PassSmaniotto 2022 Table A.1 — the Oluokun law driven by the same anchors over-predicts the 7-d strength by more than CEB-FIP does
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tunnel-face-pressure-web-validationrecords a differenceWeb-validation for `tunnel-face-pressure.ts` — the required closed-face TBM face support pressure by the DAUB 2016 wedge-silo and the undrained stability ratio.18 passing
Analyses validated: tunnel-face-pressure
- PassDAUB §8.1: critical sliding angle ϑcrit = 66.56° (printed)
- PassDAUB §8.1: wedge forces G, Pv, TR at ϑcrit (printed values)
- PassDAUB §8.1: circular-face earth force Emax,ci = 3237.7 kN (printed)
- PassDAUB §8.1: water force Wci = 14137.2 kN and total Sci = 19700.5 kN (printed)
- PassDAUB §8.1: minimum crown pressure s_crown,min = 190.8 kN/m² (printed)
- PassDAUB §8.1: working band 201 → 219 kN/m² (printed conclusion)
- PassDAUB §8.1: water floor 1.05 × groundwater = 136.5 kN/m² (printed check)
- PassCoefficient sets: Anagnostou & Kovári (K2=0.4) requires ≥ the DAUB/Jancsecz force
- PassDeep overburden (t > 2D) engages the Janssen silo branch (DAUB Eq. 12)
- PassShallow overburden (t ≤ 2D) uses the full-overburden branch (DAUB Eq. 11)
- PassDAUB §8.2: Atkinson & Mair Ncr = 6.537 and N = 4.358 (printed)
- PassDAUB §8.2: support pressure at axis s_axis = 213.7 kN/m² (printed)
- PassDAUB §8.2: minimum crown pressure s_crown,min = 143.7 kN/m² (printed)
- PassDAUB §8.2: working band 174 → 211 kN/m² (printed conclusion)
- PassDAUB §8.2: stability-ratio family — Broms ≤ 6, Davis lower bound ordering
- PassDAUB §8.2: Davis local-failure check γ2,sat·D/cu ≤ 10.96 (Eq. 26)
- Passwrapper: input validation
- Passwrapper: shallow-cover warning fires below 1·D overburden
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tunnel-ground-reaction-web-validationrecords a differenceDedicated validation for the tunnel ground reaction curve (`tunnel-ground-reaction.ts`) — the convergence-confinement closed form for a circular tunnel in a Mohr-Coulomb, zero-plastic-volume-change rock mass under a hydrostatic field stres…16 passing
Analyses validated: mohr-coulomb, tunnel-ground-reaction
- PassHoek (2006) Fig.4: replicated spreadsheet inputs equal the printed intermediate values
- PassHoek (2006) Fig.4: engine reproduces the printed Output row (pi = 0)
- PassHoek (2012) RocSupport Fig.4: characteristic curve end point (pi = 0)
- PassBrady & Brown (2004) §11.3: strength parameters and critical support pressure
- PassBrady & Brown (2004) Table 11.1: elastic-branch wall displacement δi (m), 3 d.p. printed
- PassCarranza-Torres (2003) Fig.5: intermediate computations and critical pressure
- PassCarranza-Torres (2003) Fig.5: plastic radius and wall convergence (ψ = 0°)
- PassCarranza-Torres (2004) App.A: engine HB parameters at GSI = 50 (self-consistent)
- PassC-T&F (1999) §4.3: Hoek-Brown critical internal pressure p*i = 16 MPa
- PassShotcrete/concrete capacity — H&B (1980) Eq. (121) exact closed form (Table 17 cross-checked)
- PassShotcrete/concrete capacity — H&B (1980) Table 17 PRINTED values, read by the inner lining radius (ro = ri + tc)
- PassSteel-set capacity — Hoek (2012) corrected Eq. (14), cross-checked (SOURCES-GRC §7.2)
- PassRockbolt capacity — H&B (1980) Table 17 rows H, I, J, K (Eq. 128/18, radius-independent)
- PassCombined support stiffness and capacity — H&B (1980) Eq. (129) additivity
- PassEquilibrium: FS = psmax/peq; support installed after ui0 (Hoek 2012 §5.3)
- PassRocSupport Tutorial Example 1 — NOT ASSERTED (finding, not a widened tolerance)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tunnel-grout-pressure-web-validationrecords a differenceWeb-validation for `tunnel-grout-pressure.ts` — annular grout-pressure bounds and the shield conicity → PLAXIS contraction (volume-loss) relation.13 passing
Analyses validated: tunnel-grout-pressure
- PassConicity: volume loss = 1 − (Dl/Dexc)² (PLAXIS contraction), exact
- PassConicity: overcut enlarges the excavation diameter
- PassConicity: gap-closure fraction scales the volume loss
- PassConicity: >3% geometric loss trips the PLAXIS small-volume-loss warning
- PassConicity: Sophia Rail Tunnel geometry (D_exc 9.5 m, lining ext 8.7 m)
- PassSophia crown: overburden ≈ 200 kPa reproduces the printed figure
- PassSophia grout band: crown ≈ 200 kPa, invert ≈ 370 kPa from the gradient
- PassGrout band: blow-out upper bound 0.9·σv,crown,min (DAUB Eq. 5 analogy)
- PassGrout band: lower bound is max(effective overburden, pore pressure) + margin
- PassGrout band: shallow cover closes the window and warns
- PassGrout band: hydrostatic grout gradient is the floor for the injection gradient
- Passwrapper: input validation
- Passwrapper: lining larger than excavation warns
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tunnel-ldp-web-validationrecords a differenceDedicated validation for the longitudinal displacement profile (`tunnel-ldp.ts`) — the radial wall displacement u(X) as a function of distance from the advancing face, for a circular tunnel in a hydrostatic stress field.13 passing
Analyses validated: tunnel-ldp
- PassV&D Eq. (5): normalised face displacement u0* against R* (exact closed form)
- PassV&D §5/Fig. 12 example: R* = 5 → u0* ≈ 0.16 (Fig. 9 reading / printed example)
- PassV&D Eq. (6): ahead of the face u* = u0*·e^(X*) (exact closed form)
- PassV&D Eq. (7): behind the face u* = 1 − (1−u0*)·e^(−3X*/2R*) (exact closed form)
- PassV&D continuity at the face (Eq. 6 ≡ Eq. 7 at X* = 0) and far-field asymptote u* → 1
- PassV&D Fig. 4 ordering: larger R* closes later (B–E cases, RT = 5 m)
- PassPanet Eq. (1): u* = 1/4 + 3/4·[1 − (3/4)²/(3/4+X*)²] (exact closed form)
- PassÜnlü-Gerçek Eqs. (2)-(3): face value and both branches (exact closed form, ν = 0.25)
- PassHoek 2012 Fig. 6: printed face value uif/uim = 0.2622 at rpm/ro = 1.592
- PassHoek 2012 Fig. 6: printed face displacement uif = 0.011197 m from uim = 0.0427 m
- PassHoek 2012 Fig. 7: support 5 m behind face → printed ui = 0.0304 m
- Passwrapper: X* normalisation and the R* > 2 squeezing warning (V&D §4)
- Passwrapper: errors for non-positive radius / NaN, RP < RT clamped to elastic
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tunnel-lining-check-web-validationWeb validation for `tunnel-lining-check` — benchmark values from ITA WG2 Report n°22 (2019) "Guidelines for the design of segmental tunnel linings" (ISBN 978-2-9701242-1-4), with the joint equations reproduced in closed form.8 passing
Analyses validated: tunnel-lining-check
- PassITA WG2 2019 published guideline values reproduce verbatim (≥20 cited)
- Passcontact-zone bursting reproduces ITA WG2 2019 Eqs 14–15 (closed form)
- PassJanßen joint rotation reproduces ITA WG2 2019 Eqs 10–13 (closed form)
- Passa lightly loaded joint stays closed (θ ≤ θ_crit, Eq. 10) with k_r from Eq. 12
- PassM–N interaction has exactly four analytical corner points
- Passreports a utilisation per ring, the governing ring, and each code path runs
- Passthe M–N utilisation is D/C at the demand axial load
- Passrejects missing/invalid geometry rather than inventing a result
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tunnel-monitoring-web-validationWeb-validation of the tunnel-monitoring loop against PUBLISHED case-history values.8 passing
Analyses validated: tunnel-ldp, tunnel-monitoring
- PassA1: Nyren (1998) JLE St James's Park published geometry (D&G 2015 §2.2)
- PassA2: Nyren towards-tunnel half-trough V_L = 1.8 % (the asymmetry finding)
- PassA3: Peck (1969) clay K range 0.4–0.6 and O'Reilly & New K = 0.25 sand (cited values 7-10)
- PassB: published V_L ranges bracket the back-analysed values (M-T-B 1996 §2.1)
- PassC: CTRL EPBM measured V_L values back-analysed (ITA/AITES 2007 §4.3.7)
- PassD: trigger defaults anchored to Rankin (1988) 10 mm screen; convergence red = 1 % of D (Hoek)
- PassE: LDP fit on the V&D 2009 shape returns the imposed final convergence (Eq. 5 anchor)
- PassFULL LOOP: design 1.1 % but measured 1.8 % (Nyren asymmetry) → amber/red + updated prediction
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tunnel-settlement-trough-extended-web-validationrecords a differenceDedicated validation for the extended settlement-trough engine (`tunnel-settlement-trough-extended.ts`): the Peck (1969) Gaussian surface trough, the Mair, Taylor & Bracegirdle (1993) sub-surface trough, the Attewell/O'Reilly-New horizonta…10 passing
Analyses validated: tunnel-settlement-trough-extended
- PassSmax identity: Smax = 0.31·Vl·D²/i = Vs/(i·√2π) (M-T-B 1996 eq 5)
- PassGaussian profile: Sv(y) = Smax·exp(−y²/2i²) — inflection at 0.606·Smax
- PassO'Reilly & New K values: 0.5 clay / 0.25 sand (Mair & Taylor 1997 eq 5)
- PassSub-surface trough width: i(z)/z0 = 0.175 + 0.325(1−z/z0) (Divall & Goodey eq 4)
- PassSub-surface settlement: trough volume conserved, Smax grows with depth
- PassHorizontal displacement: Shmax = 0.61·K·Smax at the inflection point (M&T 1997 eq 10)
- PassHorizontal strain: compressive for |y| < i, tensile for |y| > i, zero at y = i
- PassTwin-tunnel superposition: Sv = Svmax[exp(−y²/2i²) + exp(−(y−d)²/2i²)] (D&G eq 6)
- PassTwin-tunnel interaction warning for clear spacing < 1 D (M-T-B 1996 §2.4)
- PassInput validation: D, z0, Vl errors; K warning
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tunnel-settlement-trough-web-validationrecords a differenceDedicated validation for the tunnel surface settlement trough (`tunnel-settlement-trough.ts`): the Gaussian transverse profile S(y) = Smax·exp(−y²/2i²) with i = K·z0 and Smax = VL·(πD²/4)/(i·√(2π)).6 passing
Analyses validated: tunnel-settlement-trough
- PassPound & Beveridge (2002) Table 3: printed Smax from printed z0, VL and K (D = 6.12 m)
- PassPound & Beveridge (2002) chainage 21320: two tunnels 18.0 m apart superpose to the printed 21.0 mm
- PassPound & Beveridge (2002) chainage 22670: tunnels 38 m apart give a double low point
- PassBowers, Hiller & New (1996) Table 1: type three sections, printed Smax from printed VL and K
- PassFillibeck & Vogt (2012) Fig.2: printed smax lies inside the engine range for the stated At = 35-42 m²
- Passhand check: the engine profile integrates to its own trough volume and peaks at the inflection slope
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Rock mechanics and rock slopes
1 finite-element rows · 1 closed-form problems · 9 validation suites
Finite-element solver registry
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
uniaxial strength of a column with one joint set, β = 30…90° (13 angles), FE column through the phase driver v-rs2-jointed-column-table-6-2 | [3.4641, 3.57266, 3.93923, 4.73205, 6.51038, 8.57803] | [3.4641, 3.57266, 3.93923, 4.73205, 6.51038, 8.57803] | 0.00 % | Ours [3.4641, 3.57266, 3.93923, 4.73205, 6.51… kPaPublished [3.4641, 3.57266, 3.93923, 4.73205, 6.51… kPa0.00 % | Pass | |
| ||||||
Closed-form engine registry
| Problem | Ours | Published | Difference | Tolerance | Status | Details | |
|---|---|---|---|---|---|---|---|
Rock planar slide, no tension crack, saturated — Sau Mau Ping Road slope D2-ROCKPLANAR-SAUMAUPING | 0.818425 | 0.818425 | 0.00 % | ± 0.1 % | Ours 0.818425Published 0.8184250.00 % | Pass | |
| |||||||
Cited validation suites
barton-bandis-web-validationValidation for Barton-Bandis rock-joint strength (`barton-bandis.ts`).13 passing
Analyses validated: barton-bandis
- Passat σn′ = JCS the roughness term vanishes → φ_peak = φr
- Passdilation increases as σn′ decreases (rougher engagement at low stress)
- Passrougher joint (higher JRC) is stronger at the same σn′
- Passfriction cap prevents blow-up as σn′ → 0
- Passpeak friction = JRC·log10(JCS/σn) + φr (spot value)
- PassBarton-Choubey φ_peak = JRC·log10(JCS/σn) + φr — cited sweep
- PassBarton-Choubey dilation i = JRC·log10(JCS/σn) — cited sweep
- PassBarton-Choubey shear strength τ = σn·tan φ_peak — cited values
- PassBarton-Choubey: rougher joint (JRC) raises φ_peak by JRC·log10(JCS/σn) — cited
- PassWyllie & Mah §4.2.4 (p. 85): roughness angle i = 5·log10(8600/426) ≈ 7°
- PassWyllie & Mah §6.3.5 (p. 137): rough plane slope, σ = 281 kPa → τ 269, φ+i 44°, FS 1.66
- PassWyllie & Mah §6.3.5 (p. 137): rough plane slope, σ = 450 kPa → τ 387, φ+i 41°, FS 1.49
- Passthe published-value tally is 7 distinct printed numbers from 1 source; PARTIAL (short of 20 by 13)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rock-mechanics-published-web-validationrock-mechanics — deep review D13 (2026-10-02).8 passing
Analyses validated: rock-mechanics
- Pass[PRE12] RMR worked example — 12 + 13 + 10 + 22 + 7 − 5 = 59, Class III fair rock
- Pass[PRE12 Table E] soft filling < 5 mm rates 2 (not 1) — the same as hard filling > 5 mm
- Pass[PRE12 Table B] orientation adjustments: tunnels to −12, foundations to −25, slopes to −60 accepted; outside refused
- Pass[PRE12] Q worked example — (90/4)(3/1)(1/15) = 4.5, "Fair"
- Pass[HB02] σci 50, mi 10, GSI 45 — tunnel D 0: φ′ 47.16°, c′ 0.58 MPa; slope D 1: φ′ 27.61°, c′ 0.35 MPa
- Pass[PRE5] Athens schist — mi 9.6, GSI 20 → mb 0.55, s 0.0001, a 0.544
- Pass[PRE5 / SG 26.1] GSI uses RMR'89 — groundwater 15, orientation 0 — not the design RMR
- Pass[SG 26.2-26.3] At the RMR'89 floor, GSI = 9 ln Q' + 44 with Q' = (RQD/Jn)(Jr/Ja) when it gives GSI < 18
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rock-mechanics-web-validationrecords a differenceC.ROCK — `rock-mechanics` web-benchmark: the generalised Hoek-Brown parameters against the published equations, 34 cited values.17 passing
Analyses validated: rock-mechanics
- PassC.ROCK.1: 30 Hoek-Brown parameters match published Eqs (4)-(6) exactly
- PassC.ROCK.2: the published intact-rock limit — s = 1 and a = 0.5 at GSI = 100, D = 0
- PassC.ROCK.3: Eq (6) asymptote as GSI → 0
- PassC.ROCK.4: disturbance D strictly weakens the rock mass (Eqs 4 and 5)
- PassC.ROCK.5: Q-system formula identity and Barton class boundaries
- PassC.ROCK.6: GSI ≈ RMR89 − 5 (Hoek & Brown 1997) with the published floor
- PassC.ROCK.7: R4 sub-ratings sum and clamp per Bieniawski 1989 Table 4.4
- PassC.ROCK.8: E-5 regression — a non-finite input must error, never yield NaN
- PassC.ROCK.9: E-112 — a NaN Q must never be labelled "Exceptionally good"
- PassC.ROCK.10: E-112 — Q is a product of positive ratios and cannot be negative
- PassC.ROCK.11: E-112 — Hoek-Brown must reject blank inputs instead of returning NaN
- PassC.ROCK.12: E-112 — s ≤ 1 always, because s = 1 IS intact rock (Hoek & Brown 2019 Eq. 5)
- PassC.ROCK.13: E-112 — σ1 clamps to the tension cut-off instead of returning NaN
- PassC.ROCK.14: E-112 — the Mohr-Coulomb fit must not return a modulus beside a NaN cohesion
- PassC.ROCK.15: E-112 — the modulus engine must reject blanks, not return half a result
- PassC.ROCK.16: E-112 — jcond89FromJrJa must not return the r→∞ limit for an invalid Ja
- PassC.ROCK.17: E-112 — a failed RMR must not become a valid GSI downstream
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rock-slope-stability-rocplane-web-validationrock-slope-stability — second dedicated validation suite beside the Example 6.1 suite already in `rock-slope-stability-web-validation.test.ts` (which rests on ONE source).14 passing
Analyses validated: rock-slope-stability
- Pass[W] Example 6.1(c) drained: W·cosψp = 1017.14, W·sinψp = 712.21, c·A = 333.50 kN/m
- Pass[W] Example 6.1(b) crack full (zw = 4.35 m): U = 284.57, V·sinψp = 53.23, V·cosψp = 76.02 kN/m
- Pass[W] Example 2.2, east-dipping 50/090 face: plane failure possible on joint set 2 ONLY
- Pass[W] Example 2.2: cutting the east face at 40° (coincident with set 2) prevents sliding; φ > 40° also prevents it
- Pass[W] Example 2.2, north-dipping 50/360 face: no planar mode (wedge is the published mode)
- Pass[W] Example 2.2: wedge of sets 1 & 2 — line of intersection plunge ≈ 27°, possible at 50°, prevented by a 27° cut
- Pass[R1] Hoek/Sau Mau Ping, no crack: W = 28.6278 MN/m, A = 104.6068 m²/m
- Pass[R1] Hoek/Sau Mau Ping, with crack: z = 14.0092 m, W = 24.8439 MN/m, A = 80.1826 m²/m, FS = 1.0654738
- Pass[R6] Priest (1993): plane failure with 25 %-filled 15 m crack → FS = 1.049
- Pass[R8] Watts & West (1985) case 1: c′ = 0 t/ft², φ′ = 20° → FS = 0.364
- Pass[R8] Watts & West (1985) case 2: c′ = 1.1025 t/ft², φ′ = 20° → FS = 0.644
- Pass[R8] Watts & West (1985) case 3: c′ = 2.2051 t/ft², φ′ = 35° → FS = 1.26
- Pass[R3] RocPlane Table 1.3.3: 15 (z/H, c) points of the tension-crack / cohesion sensitivity grid
- Pass[R3] dry, no-crack, no-cohesion limit is tanφ/tanψp = 0.824542 (printed first row, c = 0)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rock-slope-stability-web-validationREAL PUBLISHED TEXTBOOK WORKED EXAMPLE (not formula-fidelity -- an independently-published answer) from Wyllie & Mah, "Rock Slope Engineering -- Civil and Mining", 4th ed.10 passing
Analyses validated: rock-slope-stability
- Pass[1-2] (c) fully drained (zw=0): published W=1241.70 kN/m, A=13.34 m2/m, FS=1.54
- Pass[3-5] (a) water to 3m above the sliding surface (zw=3): published U=196.31 kN/m, V=44.15 kN/m, FS=1.25
- Pass[6] (b) tension crack completely full (zw=4.35m): published FS=1.07
- Pass[7] (d) drained AND cohesion reduced to zero: published FS=1.08
- Pass[8] status classification bands (unstable<1.0, marginal<1.3, else stable) match the published FS=1.25 marginal call
- Pass[9] the drained case (FS=1.54) is classified stable, matching the textbook's own qualitative call
- Pass[10] the fully-flooded case (FS=1.07) is classified marginal, matching the textbook noting it "is close to failure"
- Pass[11] kinematic admissibility for this exact published geometry: the plane daylights (psi_p=35 < psi_f=60) and exceeds friction (35 > 37 is FALSE -- so planar_admissible must be FALSE, since 35 < 37)
- Pass[12] invalid inputs (zero height, dip/face angle outside 0-90, tension crack >= height) are refused
- Pass[VAL-1] Example 6.1(e): critical crack depth of the dry slope = 4.32 m (z/H = 0.36, chart) — engine FS minimum and closed form agree within the chart resolution
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rock-wedge-3d-independent-web-validationINDEPENDENT-SOURCE validation, 3-D rock wedge engine (`rock-wedge-3d.ts`).10 passing
Analyses validated: not attributed by the manifest
- Pass[S1] §1.1 Table 1.1.5 (T35): joints 45/141 & 45/219, face 70/180 ⇒ plunge 37.852°; FS ≅ 1
- Pass[S1] §1.1 Table 1.1.5 (T33 & T37): dip/φ 42.7/33 ⇒ 35.645°; 47.5/37 ⇒ 40.301°
- Pass[S1] §1.3 (Kumsar et al. 2000 Case 3, Ankara Castle): FS = 0.7123
- Pass[S1] §1.4 (Kumsar et al. 2000 Case 4, Dinar, static): FS = 2.0203
- Pass[S1] §3.1 Table 3.1.3 (ponded-water problem, dry row): FS = 0.9218
- Pass[S1 §1.1] Kovári & Fritz closed form: λ = 1/sin ω and FS = λ·cos i_a·tanφ/sin i_a
- Pass[S2] §5.3: wedge factors A = 0.91 and B = 0.80
- Pass[S2] §5.3: drained FS = 1.23 and cohesion destroyed ⇒ FS = 1.01
- Pass[S3] Ch 8: line of intersection αi = 349°, βi = 39° (stereonet reading) and 348.5°/39.3° (Table 8.1)
- Pass[S3] Ch 8 + Table 8.1: H = 25 m toe-to-crest ⇒ W = 7,203,843 kg, FS = 0.875 (c ≠ 0), 0.686 (c = 0); Kliche FS 0.879
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rock-wedge-3d-web-validation3-D wedge engine vs the published worked wedges in Wyllie & Mah (2004) "Rock Slope Engineering — Civil and Mining" 4th ed., Spon (source on disk: Wyllie-Mah-Rock-Slope-Engineering-Civil-and-Mining-4e.pdf).9 passing
Analyses validated: not attributed by the manifest
- PassTable 7.2: the line of intersection plunges ψ5 = 31.2° and the wedge is a valid, daylighting two-plane wedge
- PassTable 7.2: wedge factors A = 1.548 and B = 0.956 (eqs 7.12-7.13)
- Pass§7.5 eq 7.14 / Table 7.2: friction-only FS = A·tanφA + B·tanφB = 1.24
- Pass§7.4: completely drained FS with cohesion = 1.98
- PassTable 7.2: saturated FS with cohesion = 1.36
- Pass§7.4: zero cohesion and maximum water pressure (saturated) = 0.62 — the worst case, unstable
- PassTable 7.2 ordering holds: drained 1.98 > saturated 1.36 > friction-only 1.24 > worst case 0.62
- Pass§7.6.3 case (i): planes 60/360 and 54/118, φ = 30°, c = 0, dry ⇒ FS = 1.05
- Pass§7.6.3 case (i) is size-independent: the same orientations at H = 5 m and H = 200 m give the same FS
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rockfall-trajectory-web-validationWeb-validation for the rockfall-trajectory engine (`rockfall-trajectory.ts`).25 passing
Analyses validated: rockfall-trajectory
- PassA. frictionless slide toe velocity = √(2gH) for H=10 m
- PassA. frictionless slide toe velocity = √(2gH) for H=20 m
- PassA. frictionless slide toe velocity = √(2gH) for H=30 m
- PassA. frictionless slide toe velocity = √(2gH) for H=50 m
- PassA. frictionless slide toe velocity = √(2gH) for H=100 m
- PassB. friction slide v_toe = √(2gH(1−μ/tanβ)) for H=30 β=60 μ=0.4
- PassB. friction slide v_toe = √(2gH(1−μ/tanβ)) for H=20 β=45 μ=0.3
- PassB. friction slide v_toe = √(2gH(1−μ/tanβ)) for H=40 β=70 μ=0.5
- PassB. friction slide v_toe = √(2gH(1−μ/tanβ)) for H=15 β=50 μ=0.35
- PassB. friction slide v_toe = √(2gH(1−μ/tanβ)) for H=25 β=55 μ=0.45
- PassC1. kinetic energy at the toe = ½ m v² (definition)
- PassC2. higher normal restitution R_n → longer runout & higher bounce
- PassC3. elastic (R_n=R_t=1) conserves energy → block does not arrest (runs to cap)
- PassC4. more dissipative bounces (lower R) → fewer/shorter → shorter runout
- PassD. Ritchie ditch for H=5 β=45 → 3.7 m × 1 m
- PassD. Ritchie ditch for H=15 β=60 → 7 m × 1.5 m
- PassD. Ritchie ditch for H=25 β=80 → 7.6 m × 1.8 m
- PassD. Ritchie ditch for H=8 β=40 → 3.7 m × 1.2 m
- PassE1. taller slope → higher toe velocity
- PassE2. steeper face → higher toe velocity (larger downslope gravity component)
- PassF. μ ≥ tanβ (friction angle ≥ slope angle) → block arrests on the face
- PassG1. a low barrier in the bounce path is overtopped (inadequate)
- PassG2. a tall, strong barrier is adequate
- PassW3-D5 rockfall: Rn = 0 and Rt = 0 are honoured (0 = perfectly plastic), > 1 refused; a plastic impact rolls on
- PassW3-D5 rockfall: a barrier at the toe (offset 0) is assessed; a barrier without a height is not assessed (it read ADEQUATE)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
stereonet-web-validationStereonet + kinematic screening vs the published worked examples in Wyllie & Mah (2004) "Rock Slope Engineering — Civil and Mining" 4th ed., Spon, Ch 2: Example Problem 2.1 (stereo plots of structural geology data, p.10 passing
Analyses validated: not attributed by the manifest
- PassExample 2.1(b): clustering the 17 poles finds the book's three sets and sets 80/010 aside
- PassExample 2.1(b): mean poles agree with the book's 78/305, 40/081, 20/163 to within 2° of arc
- PassExample 2.1(c): angle between the mean poles of sets 1 and 3 is 94° (included angle 86°)
- PassExample 2.1(e): the line of intersection of sets 1 and 2 plunges 27° toward 029°
- PassExample 2.2: east-dipping 50° face, φ = 25° ⇒ plane failure on set 2 only
- PassExample 2.2: cutting the east slope at 40°, coincident with set 2, prevents sliding on set 2
- PassExample 2.2: if the friction angle exceeded the 40° dip, sliding on set 2 would not occur
- PassExample 2.2: north-dipping 50° face ⇒ wedge failure on sets 1 and 2, and no plane failure
- PassExample 2.2: cutting the north slope at 27° (the intersection plunge) is not undercut by the wedge
- Passclosed form: the wedge daylights exactly when ψf exceeds atan(tanψi / cos(αi − αf)) (≈ 30.3° for sets 1+2 on a north face)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Groundwater flow and seepage
32 finite-element rows · 0 closed-form problems · 19 validation suites
Finite-element solver registry
Showing 32 of 32 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
Dam I: total discharge under the dam plaxis-verif-concrete-dam-I-Q | 1.031e-5m³/s/m | 1.029e-5m³/s/m | +0.15 % | Ours 1.031e-5 m³/s/mPublished 1.029e-5 m³/s/m+0.15 % | Pass | |
| ||||||
Dam II (upstream screen): total discharge plaxis-verif-concrete-dam-II-Q | 8.686e-6m³/s/m | 8.840e-6m³/s/m | −1.74 % | Ours 8.686e-6 m³/s/mPublished 8.840e-6 m³/s/m−1.74 % | Pass | |
| ||||||
Dam III (downstream screen): total discharge plaxis-verif-concrete-dam-III-Q | 8.686e-6m³/s/m | 8.840e-6m³/s/m | −1.74 % | Ours 8.686e-6 m³/s/mPublished 8.840e-6 m³/s/m−1.74 % | Pass | |
| ||||||
Dam I: uplift pressure head at A (dam toe) plaxis-verif-concrete-dam-I-uplift | 2.181m | 2.25m | −3.07 % | Ours 2.181 mPublished 2.25 m−3.07 % | Pass | |
| ||||||
Dam II: uplift pressure head at A plaxis-verif-concrete-dam-II-uplift | 2.073m | 2.13m | −2.68 % | Ours 2.073 mPublished 2.13 m−2.68 % | Pass | |
| ||||||
Dam III: uplift pressure head at A (upstream side of the screen) plaxis-verif-concrete-dam-III-uplift | 4.004m | 3.87m | +3.46 % | Ours 4.004 mPublished 3.87 m+3.46 % | Pass | |
| ||||||
seepage face length along the slope above the tail water plaxis-verif-seepage-length | 25.375m | 25.5m | −0.49 % | Ours 25.375 mPublished 25.5 m−0.49 % | Pass | |
| ||||||
seepage face height on the downstream boundary above the tail water plaxis-verif-muskat | 1.5867m | 1.55m | +2.37 % | Ours 1.5867 mPublished 1.55 m+2.37 % | Pass | |
| ||||||
total discharge through an unconfined sand layer plaxis-verif-sand-layer-Q | 0.15387m³/day/m | 0.15m³/day/m | +2.58 % | Ours 0.15387 m³/day/mPublished 0.15 m³/day/m+2.58 % | Pass | |
| ||||||
total discharge through the earth dam plaxis-verif-earth-dam-Q | 0.00054579m³/s/m | 0.000536m³/s/m | +1.83 % | Ours 0.00054579 m³/s/mPublished 0.000536 m³/s/m+1.83 % | Pass | |
| ||||||
total discharge Q = kL/2 through the triangular dam plaxis-verif-triangular-dam-Q | 0.5m³/day/m | 0.5m³/day/m | 0.00 % | Ours 0.5 m³/day/mPublished 0.5 m³/day/m0.00 % | Pass | |
| ||||||
steady head at r = 10 m (pumping well, axisymmetric) plaxis-verif-theis-thiem-r10 | 13.5342m | 13.5342m | 0.00 % | Ours 13.5342 mPublished 13.5342 m0.00 % | Pass | |
| ||||||
steady head at r = 100 m plaxis-verif-theis-thiem-r100 | 14.2678m | 14.2678m | 0.00 % | Ours 14.2678 mPublished 14.2678 m0.00 % | Pass | |
| ||||||
steady suction head profile, worst |ψ − Gardner| over y = 0.5…3 m plaxis-verif-infiltration-steady | 3.490e-7m | 0m | — | Ours 3.490e-7 mPublished 0 m— | Pass | |
| ||||||
transient suction head, worst |ψ − Srivastava & Yeh| at t = 0.1/0.25/0.5/1/5 d plaxis-verif-infiltration-transient | 0.0014m | 0m | — | Ours 0.0014 mPublished 0 m— | Pass | |
| ||||||
steady suction head, worst |ψ − Gardner| plaxis-verif-evaporation-steady | 9.800e-5m | 0m | — | Ours 9.800e-5 mPublished 0 m— | Pass | |
| ||||||
transient suction head, worst |ψ − Srivastava & Yeh| plaxis-verif-evaporation-transient | 0.0018m | 0m | — | Ours 0.0018 mPublished 0 m— | Pass | |
| ||||||
confined flow box: discharge and linear head (P2/P1 and equal order) k4-gate-confined-box | 1m³/day/m | 1m³/day/m | 0.00 % | Ours 1 m³/day/mPublished 1 m³/day/m0.00 % | Pass | |
| ||||||
unconfined flow, sharp vG soil: discharge vs Dupuit k4-gate-dupuit | 2.117e-5m³/s/m | 2.100e-5m³/s/m | +0.82 % | Ours 2.117e-5 m³/s/mPublished 2.100e-5 m³/s/m+0.82 % | Pass | |
| ||||||
Thiem steady drawdown (see plaxis-verif-theis-thiem-*) k4-gate-thiem | 13.5342m | 13.5342m | 0.00 % | Ours 13.5342 mPublished 13.5342 m0.00 % | Pass | |
| ||||||
fe-seepage (TS oracle) layered column discharge k4-crosscheck-fe-seepage-layers | 5.600e-5m³/s/m | 5.600e-5m³/s/m | 0.00 % | Ours 5.600e-5 m³/s/mPublished 5.600e-5 m³/s/m0.00 % | Pass | |
| ||||||
fe-seepage block with a cutoff: discharge vs the oracle 80×40 Q4 k4-crosscheck-fe-seepage-block · Self-check | 1.229e-5m³/s/m | 1.229e-5m³/s/m | +7.0e-3 % | Ours 1.229e-5 m³/s/mPublished 1.229e-5 m³/s/m+7.0e-3 % | Pass | |
| ||||||
unconfined-seepage (TS oracle): discharge (Hypres coarse vG) k4-crosscheck-unconfined · Self-check | 2.109e-5m³/s/m | 2.087e-5m³/s/m | +1.07 % | Ours 2.109e-5 m³/s/mPublished 2.087e-5 m³/s/m+1.07 % | Pass | |
| ||||||
worst |ψ − Srivastava & Yeh| under a rainfall table (24 values, 4 global times) k9-sy-rainfall-hyetograph | 0.0015m | 0m | — | Ours 0.0015 mPublished 0 m— | Pass | |
| ||||||
Δh at 8 m depth after 1 day of a 0.5 m/day head ramp k9-drawdown-ramp-8m | -0.185m | -0.185m | 0.00 % | Ours -0.185 mPublished -0.185 m0.00 % | Pass | |
| ||||||
Fredlund–Xing–Huang k_r at 10 kPa (a 10, n 2, m 1, ψr 3000, aev 5) k9-fxh-kr-10kPa | 0.210328 | 0.210374 | −0.02 % | Ours 0.210328Published 0.210374−0.02 % | Pass | |
| ||||||
leakage through a clay blanket (Yolo light clay / Superstition sand) k9-kisch-liner-Q | 1.323e-7m/s | 1.323e-7m/s | −7.6e-3 % | Ours 1.323e-7 m/sPublished 1.323e-7 m/s−7.6e-3 % | Pass | |
| ||||||
worst |ψ − Srivastava & Yeh| at t = 0.1/0.25/0.5/1/5 d, y = 0.5…3 m (ASSERTED < 5 mm); infiltration 0.1 m/d v-plaxis-infiltration-transient-asserted | 0.0014m | 0m | — | Ours 0.0014 mPublished 0 m— | Pass | |
| ||||||
worst |ψ − Srivastava & Yeh| at the same times (ASSERTED < 5 mm); evaporation 0.002 m/d v-plaxis-evaporation-transient-asserted | 0.00185m | 0m | — | Ours 0.00185 mPublished 0 m— | Pass | |
| ||||||
worst |ψ − S&Y superposed| under a table flow function (re-run 3 Nov 2026) v-k9-flow-function-rainfall | 0.0015m | 0m | — | Ours 0.0015 mPublished 0 m— | Pass | |
| ||||||
Δh at 8 m after 1 d of a 0.5 m/d head ramp (head and level functions; re-run 3 Nov 2026) v-k9-flow-function-drawdown | -0.185m | -0.185m | — | Ours -0.185 mPublished -0.185 m— | Pass | |
| ||||||
worst |σ′yy − (−(γsat − γw)·d)| of a 2 m drained column (γsat 20, γw 10) under 0 / 1.5 / 3 m of standing water above its surface v-rocscience-ponded-water-effective-stress | 5.862e-13kPa | 0kPa | — | Ours 5.862e-13 kPaPublished 0 kPa— | Pass | |
| ||||||
Cited validation suites
capillary-rise-web-validationValidation for `capillary-rise` — Hazen/Terzaghi capillary rise h_c = C/(e·D10) and suction (`capillary-rise.ts`, `computeCapillaryRise`).6 passing
Analyses validated: capillary-rise
- PassTerzaghi–Peck–Mesri Eq. 15.23 at the printed C limits (0.01 and 0.05, D10 in mm, h_c in m)
- Passthe engine’s C warning band is exactly the published 0.01–0.05 (= 0.1–0.5 cm²)
- PassTerzaghi–Peck Eq. 15.21 and Craig p. 40: suction = γw·h_c with γw = 9.81 kN/m³
- PassTerzaghi–Peck Art. 15.6.1: rise grows as the effective size falls, and is ∝ 1/D10 and ∝ 1/e
- PassHoltz & Kovacs Table 6-1 / Example 6.3: a clay with D10 = 1 µm rises at least 10 m
- PassAcharya (2021) lecture-note problem: soil A (D10 = 0.06 mm) rises 60 cm; soil B (D10 = 0.1 mm, same e) ⇒ 360 mm
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
darcy-velocity-web-validationdarcy-velocity — validation of Darcy's law (discharge velocity, seepage velocity, flow rate) against PUBLISHED worked numbers.8 passing
Analyses validated: darcy-velocity
- PassLambe & Whitman 1969 Fig 17.8: k = 0.5 cm/s, 3.6 m over 1.8 m → v = 1 cm/s
- PassLambe & Whitman 1969 Fig 17.8: n = 0.33 → seepage velocity "3 cm/sec"
- PassLambe & Whitman 1969 Fig 18.1: 4.8 m over 10 × 0.3 m → gradient 1.6
- PassLambe & Whitman 1969 Fig 18.1: Q = kiA over the 1.2 × 1.2 m tube = 0.00115 m³/s
- PassHoltz & Kovacs 1981 Ex 7.1: printed k = 0.08 cm/s reproduces the collected volume (945.7 cm³ in 1 min) to its 1-s.f. precision
- PassHoltz & Kovacs 1981 Ex 7.1: cross-sectional area of the 7.3 cm sample is 41.9 cm² (printed)
- Passv_s > v for every porosity below 1 (Lambe & Whitman Eq. 17.3: v_s = v/n)
- Passa cleared flow length is refused rather than reported as v = 3e9 m/s
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
dewatering-system-web-validationDedicated validation for the equivalent-well dewatering system (`dewatering-system.ts`): steady discharge of a ring of wells idealised as one large well, Q = πk(H²−h²)/ln(R/re) (unconfined) and Q = 2πkbs/ln(R/re) (confined), with the Sicha…9 passing
Analyses validated: dewatering-system
- PassCashman & Preene Design Example 1: printed Q (m³/s) from the printed re and R0
- PassCashman & Preene Design Example 1: engine Sichardt R plus re equals the printed R0 (Eq. 13.15 structure)
- PassCashman & Preene Design Example 1: the engine default (no R0 added) is the conservative side, +0.7 to +2.7 %
- PassTextbook Example 4.2.2 (confined, b = 25 m): K = 16.8 m/day reproduces Q = 0.05 m³/s = 4320 m³/day
- PassTextbook Example 4.2.2 (confined, b = 30 m, 1 m dia well): K = 13.3 m/day, head at well 34.5 m, R = 79 m → Q = 113 m³/h
- PassTextbook Example 4.2.3 (unconfined, h0 = 25 m): K = 18.3 m/day reproduces Q = 0.05 m³/s = 4320 m³/day
- PassTextbook Example 4.2.4 (unconfined, 33 m saturated, 0.5 m dia well): K = 12.68 m/day, head at well 27.7 m, R = 198 m → Q = 1920 m³/day
- PassCourse handout Example 9.7 (confined well): printed drawdown 127 ft reproduces Q = 2000 gpm
- PassCourse handout Example 9.8 (unconfined well): printed drawdown 38.2 ft reproduces Q = 600 gpm
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
earth-dam-seepage-web-validationPUBLISHED-VALUES: 10 -- distinct published values for this engine (engine-level total, declared once); independent audit A4: ten values, all from one worked example (Craig Ex 2.4).16 passing
Analyses validated: earth-dam-seepage
- PassCraig 2012 Ex 2.4: focal distance x0 = 1.90 m (engine y0/2)
- PassCraig 2012 Ex 2.4: parabola ordinate at the focus, z0 = 2·x0 = 3.80 m (TABLE E, x = 0)
- PassCraig 2012 Ex 2.4: seepage from the basic parabola q = 2·k'·x0 = 1.0e-7 m³/s per metre
- PassCraig 2012 Ex 2.4: analytic q agrees with the same example's hand-drawn flow net (1.1e-7) to its own scatter
- PassCraig 2012 TABLE E: point (x=-5.0, z=7.24) lies on the parabola with y0 = 3.80 m
- PassCraig 2012 TABLE E: point (x=-10.0, z=9.51) lies on the parabola with y0 = 3.80 m
- PassCraig 2012 TABLE E: point (x=-20.0, z=12.9) lies on the parabola with y0 = 3.80 m
- PassCraig 2012 TABLE E: point (x=-30.0, z=15.57) lies on the parabola with y0 = 3.80 m
- PassCraig 2012 TABLE E: ordinate at x=-5.0 m is z=7.24 m (engine parabola y(L/2))
- PassCraig 2012 TABLE E: ordinate at x=-10.0 m is z=9.51 m (engine parabola y(L/2))
- PassCraig 2012 TABLE E: ordinate at x=-20.0 m is z=12.9 m (engine parabola y(L/2))
- PassCraig 2012 TABLE E: ordinate at x=-30.0 m is z=15.57 m (engine parabola y(L/2))
- PassCasagrande 1937 Eq.(16): q = k·y0 = 2·k·a0, with focal distance a0 = y0/2
- PassCasagrande 1937 Eq.(15): y0 = √(d²+h²) − d (hand evaluation at Craig's d = 40.80, h = 18.00)
- PassCasagrande 1937: seepage is independent of the number of channels drawn — doubling k doubles q, h→0 gives q→0
- Passfreeboard check: Craig Ex 2.4 crest (20.00 m) over the 18.00 m pool leaves 2.00 m
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-seepage-web-validationWeb-benchmark validation for `fe-seepage` — steady confined FE seepage and the unconfined free-surface solve.12 passing
Analyses validated: fe-seepage, unconfined-seepage
- Pass1-D confined flow reproduces Q = k·(Δh/L)·H exactly
- Passthe head field is linear in x, to machine precision
- PassQ scales exactly with k, with the gradient, and with the flow area
- Passrefining the mesh drives Q toward the closed form
- Passtwo zones in series give the harmonic-mean equivalent k (exact)
- Passpure horizontal flow has no upward gradient, so piping is withheld not zeroed
- Passupward flow produces a real exit gradient and a finite piping FoS
- Passthe unconfined solve reports the exact Dupuit discharge q = k(h₁² − h₂²)/(2L)
- Passthe free surface falls monotonically from upstream to downstream
- Passa domain with no fixed head is refused rather than solved as all-zero
- Passinvalid geometry, conductivity and mesh divisions are all refused
- Passthe unconfined solve refuses a downstream head above the upstream one
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
field-permeability-web-validationWeb-benchmark validation for `field-permeability` — in-situ borehole permeability.9 passing
Analyses validated: field-permeability
- Passflush-bottom shape factor is Hvorslev F = 2.75·D
- Passscreened shape factor is F = 2π·L/sinh⁻¹(L/D), with the published asymptote
- Passvariable-head k matches Hvorslev (1951) on a hand-computed case
- Passa rising-head test gives the same k as the falling-head equivalent
- Passconstant-head k matches Hvorslev k = Q/(F·H)
- Passusing the flush-bottom factor for a screened interval changes k materially
- Passa short screened interval (L/D < 4) is flagged, not silently trusted
- Passpermeability classes break at the Terzaghi-Peck decade boundaries
- Passa poor ln(H)-vs-t fit is flagged with its R²
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
filter-design-web-validationrecords a differencePUBLISHED-VALUES: 6 -- distinct published values for this engine (engine-level total, declared once); independent audit A4: the sources publish filter LIMITS, not worked filter-design answers.12 passing
Analyses validated: filter-design
- PassLambe & Whitman 1969 Eq 19.10 / Craig 2012 Eq 2.41: D15f/D85s = 4.95 (< 5) passes the USACE retention limit
- PassLambe & Whitman 1969 Eq 19.10 / Craig 2012 Eq 2.41: D15f/D85s = 5.05 (> 5) fails the USACE retention limit
- PassEM 1110-2-2300 Table B-2 (category 4, "D15 < 4 to 5 × d85"): the Terzaghi end of the band is 4 — 3.96 passes, 4.04 fails
- PassCraig 2012 Eq 2.42: D15f/D15s = 5.05 (> 5) passes the USACE permeability limit, 4.95 fails
- PassLambe & Whitman 1969 Eq 19.11 (lower bound 4): D15f/D15s = 4.04 passes the Terzaghi permeability limit, 3.96 fails
- PassLambe & Whitman 1969 Eq 19.12: D50f/D50s = 24.75 (< 25) passes, 25.25 fails
- PassEM 1110-2-2300 App. B step f: filter D15 = 0.1 mm is acceptable, 0.099 mm is not
- PassEM 1110-2-2300 App. B step g: a filter D85 of 75 mm raises no oversize advisory, 75.1 mm does
- PassEM 1110-2-2300 ¶B-6: with the total-sample d85 = 5.2 mm a D15 = 2 mm filter retains the base (ratio 0.38)
- PassEM 1110-2-2300 ¶B-6: with the matrix d85 = 0.1 mm the same D15 = 2 mm filter fails retention (ratio 20)
- Passratios: 3 mm filter on the base D15/D50/D85 = 0.02/0.1/1 mm gives 3, 150 and 30 (hand arithmetic)
- Passa cleared base D85 is refused rather than giving a ratio of 6e8
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
flow-net-seepage-web-validationflow-net-seepage — validation against PUBLISHED worked flow-net examples.18 passing
Analyses validated: flow-net-seepage
- PassCraig 2012 Fig 2.8: sheet piling, Nf=3 Nd=8 → shape factor 0.375, q = 2.25e-5 m³/s/m
- PassCraig 2012 Ex 2.1: cofferdam, Nf=6 Nd=10 H=4.50 → k = 2.6e-5 m/s from q = 0.25 m³/h/m
- PassCraig 2012 Ex 2.1: forward check — printed k = 2.6e-5 reproduces printed inflow 0.25 m³/h/m
- PassCraig 2012 Ex 2.1: hydraulic gradient below the excavation i = 0.50 (Δh = 4.50/10, Δs = 0.9 m)
- PassCraig 2012 Ex 2.2: dam spillway Nf=3 Nd=10 → shape factor 0.3, q = 3.75e-5 m³/s/m
- PassCraig 2012 Ex 2.2: a 60 m long spillway passes 60 × the per-metre seepage
- PassLambe & Whitman 1969 Fig 18.1: nf=4 nd=10 → shape factor 0.4
- PassLambe & Whitman 1969 Fig 18.1: Q/L = 0.00096 m³/s/m (per metre), Q = 0.00115 m³/s over 1.2 m
- PassLambe & Whitman 1969 Fig 18.1: gradient i = H/(10 × 0.3) = 1.6
- PassLambe & Whitman 1969 Ex 18.1: sheet pile wall → shape ½, Q/L = 18.75e-9 m³/s/m, exit i = 0.27
- PassLambe & Whitman 1969 Ex 18.2: concrete dam nf=4 nd=12.6 → shape factor 0.317
- PassLambe & Whitman 1969 Ex 18.2: Q/L = 0.00124 m³/s/m and gradient in square X = 0.19
- PassLambe & Whitman 1969 Ex 18.4: earth dam nf=2.65 nd=9 → shape factor 0.294
- PassLambe & Whitman 1969 Ex 18.4: Q/L = 5.36e-4 m³/s/m and gradient in square I = 0.40
- PassNAVFAC DM-7.01 Fig 1: dry-dock underseepage nf=6 nd=15 → 0.4 ft³/min per ft
- PassCraig 2012 p.52: refining the net (Nf,Nd) = (3,8) → (6,16) leaves q unchanged
- Passzero head loss → zero seepage and exit gradient (Darcy: no gradient, no flow)
- Passinvalid flow net (Nd = 0) is rejected, not silently floored (q would be 1e5 × too large)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
frost-depth-web-validationValidation for `frost-depth` — Stefan and modified-Berggren frost penetration (`frost-depth.ts`, `computeFrostDepth`).4 passing
Analyses validated: frost-depth
- PassTM 5-852-6 ¶3-3: volumetric latent heat 144·100·0.15 = 2160 Btu/ft³
- PassTM 5-852-6 ¶3-3: modified Berggren depth ≈ 5.8 ft (printed arithmetic 5.90 ft)
- PassCanadian Foundation Engineering Manual §13.4: L = 334 kJ/kg of water and 334 MJ/m³ of pure water
- PassMitchell & Soga Eq. 9.172 / 9.173: the modified depth is λ times the Stefan depth
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
grain-size-permeability-web-validationgrain-size-permeability — validation of the Hazen branch (and the temperature dependence used by the Kozeny–Carman branch) against PUBLISHED tabulated values.32 passing
Analyses validated: grain-size-permeability
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.1 mm → k = 1e-4 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.2 mm → k = 4e-4 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.3 mm → k = 0.9e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.4 mm → k = 1.6e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.5 mm → k = 2.5e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.6 mm → k = 3.6e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.7 mm → k = 4.9e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.8 mm → k = 6.4e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 0.9 mm → k = 0.8e-2 m/s
- PassLook 2007 Table 8.3 (row C = 0.10 ≙ engine C = 1.0): D10 = 1.0 mm → k = 1.0e-2 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.1 mm → k = 1.5e-4 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.2 mm → k = 6e-4 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.3 mm → k = 1.4e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.4 mm → k = 2.4e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.5 mm → k = 3.8e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.6 mm → k = 5.4e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.7 mm → k = 7.4e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.8 mm → k = 9.6e-3 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 0.9 mm → k = 1.2e-2 m/s
- PassLook 2007 Table 8.3 (row C = 0.15 ≙ engine C = 1.5): D10 = 1.0 mm → k = 1.5e-2 m/s
- PassLook 2007 Table 8.3 "C = 0.15" row lies outside FHWA Eq. 5-14 (C = 0.4–1.2): the engine warns
- PassCraig 2012 Eq 2.4: k = 10⁻² D10² m/s — D10 = 0.3 mm ⇒ 9e-4 m/s with the default C
- PassFreeze & Cherry 1979 Eq 8.47: A = 1.0 for K in cm/s and d10 in mm — the engine default
- PassFHWA 2006 Eq 5-14: Hazen is valid for D10 from 0.1 to 3.0 mm (inclusive) and not outside
- PassLook 2007 §8.3: Hazen is "ideally for uniformly graded material with U < 5"
- PassUSACE EM 1110-2-1906 Table VII-1: R_T(10 °C) = 1.301 ⇒ k(10)/k(20) = 0.769
- PassUSACE EM 1110-2-1906 Table VII-1: R_T(15 °C) = 1.135 ⇒ k(15)/k(20) = 0.881
- PassUSACE EM 1110-2-1906 Table VII-1: R_T(25 °C) = 0.889 ⇒ k(25)/k(20) = 1.125
- PassUSACE EM 1110-2-1906 Table VII-1: R_T(30 °C) = 0.797 ⇒ k(30)/k(20) = 1.255
- PassUSACE EM 1110-2-1906 Table VII-1: R_T(40 °C) = 0.653 ⇒ k(40)/k(20) = 1.531
- PassCraig 2012 p.41: at 10 °C the permeability is 77 % of its 20 °C value
- Passa cleared D10 is refused rather than reported as k = 1e-18 cm/s ("impermeable")
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
insitu-groundwater-web-validationWeb-benchmark validation for TWELVE anchor/pile, in-situ-test, groundwater and liquefaction-residual runner engines.12 passing
Analyses validated: cptu-dissipation, dewatering-system, drilled-shaft, earth-dam-seepage, ground-anchor, micropile, post-liquefaction-strength, spt-correction, subgrade-reaction, triaxial-csl, vacuum-preload, well-foundation
- Passground-anchor uses the BS 8081 grout-ground bond and the tendon limit
- Passvacuum-preload combines the effective vacuum with Terzaghi 1-D settlement
- Passdrilled-shaft uses the O'Neill-Reese α method and N_c = 9 base
- Passmicropile applies the FHWA-NHI-05-039 bond and composite-section limits
- Passtriaxial-csl fits the CSL through p-q states and recovers φ′
- Passcptu-dissipation reproduces Teh & Houlsby (1991)
- Passdewatering-system uses the Sichardt radius and the Dupuit unconfined flow
- Passearth-dam-seepage reproduces the Casagrande (1937) basic parabola
- Passsubgrade-reaction returns k_s = q/δ and converts units consistently
- Passwell-foundation uses Coulomb K_a/K_p and IRC 45 elastic theory
- Passspt-correction applies the Peck overburden factor over the IS 6403 bearing zone
- Passpost-liquefaction-strength applies Olson & Stark (2002)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
layered-permeability-web-validationrecords a differencelayered-permeability — validation of the equivalent horizontal (arithmetic) and vertical (harmonic) permeability of a layered deposit against PUBLISHED numbers.6 passing
Analyses validated: layered-permeability
- PassNPTEL 105101084 Lecture 24: k = 1, 0.5, 2 (×10⁻⁴ m/s), H = 6, 4, 3 m → k_h = 1.077e-4 m/s
- PassFreeze & Cherry 1979 §2.5: couplets K1 = 10⁴, K2 = 10² → Kx/Kz = 25
- PassFreeze & Cherry 1979 §2.5: couplets K1 = 10⁴, K2 = 1 → Kx/Kz = 2500
- PassFreeze & Cherry 1979 §2.5: "Kx > Kz for all possible sets of values of K1 … Kn"
- PassLambe & Whitman 1969 Ex 18.5(b): parallel tubes A (0.05 cm/s) + B (0.005 cm/s) → total Q/L = 0.495e-3 m³/s/m
- Passa zero-permeability layer is refused rather than reported as an impermeable profile
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
percolation-web-validationWeb-benchmark validation for `percolation` — falling-head percolation / infiltration test used to size soak pits and storm-water recharge.11 passing
Analyses validated: percolation
- Passthe percolation rate is the steady-state drop rate, with a consistent unit chain
- Passthe reference drop is configurable but the CLASS stays per 25 mm
- Passsuitability bands break at the published 4 / 12 / 30 / 60 min-per-25 mm edges
- Passan unsuitable result warns, and a rapid one warns about groundwater
- PassPorchet k matches the published cylindrical falling-head relation
- PassPorchet is withheld, with a reason, when the head cannot support it
- Passsoak-pit area is design flow over the allowable infiltration, with FoS 2
- Passsizing an area always carries the septic-effluent under-sizing warning
- Passa hole that was not pre-soaked for 24 h is flagged
- Passa rate that has not stabilised is flagged rather than averaged away
- Passonly the last three intervals set the rate — earlier transients are excluded
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pump-test-web-validationPUBLISHED-VALUES: 17 -- distinct published values for this engine (engine-level total, declared once); author's own count of published numbers, excluding 2 pass/fail verdicts.19 passing
Analyses validated: pump-test
- PassKruseman & de Ridder Ex 3.4: Oude Korendijk, Δs = 0.375 m → KD = 385 m²/d
- PassKruseman & de Ridder Ex 3.4: Oude Korendijk, t0 = 0.25 min, r = 30 m → S = 1.7e-4
- PassKruseman & de Ridder Ex 3.4: S = 1.7e-4 is classified as a confined aquifer, as the book treats the test
- PassKruseman & de Ridder Ex 3.6: Δs = 0.33 m → KD = 437 m²/d
- PassKruseman & de Ridder Ex 3.6: (t/r²)0 = 2.45e-4 min/m² → S = 1.7e-4
- PassKruseman & de Ridder Ex 8.1: Papadopulos test, Δs = 1.15 m → (KD)e = 173 m²/d
- PassKruseman & de Ridder Ex 8.1: OW-1 S/KD = 7.22e-7 d/m²
- PassKruseman & de Ridder Ex 8.1: OW-2 S/KD = 9.35e-7 d/m²
- PassKruseman & de Ridder Ex 8.1: OW-3 S/KD = 9.39e-7 d/m²
- PassKruseman & de Ridder Ex 15.1: Hoogezand, Q = 28.7 m³/h, Δs = 0.07 m → KD = 1800 m²/d
- PassKruseman & de Ridder Ex 17.1: UE-25b#1, Δs = 1.70 m → T = 333 m²/d
- PassKruseman & de Ridder Ex 17.1: t2 = 3.4e-3 min, r_w = 0.11 m → S = 0.15 (printed 0.146)
- PassKruseman & de Ridder Ex 17.1: S = 0.15 is "the specific yield of unconfined aquifers" (book, p.261)
- PassFreeze & Cherry 1979 Eq 8.45: SI coefficient C = 0.18 in T = C·Q/Δs
- PassFreeze & Cherry 1979 Eq 8.46: SI coefficient D = 2.25 in S = D·T·t0/r²
- PassFreeze & Cherry 1979 Eq 8.45: US-unit coefficient C = 264 (T in gal/day/ft, Q in gal/min, Δs in ft)
- PassFreeze & Cherry 1979 Eq 8.46: US-unit coefficient D = 0.3 (T in gal/day/ft, t in days, r in ft)
- Passk = T/b is arithmetic on the engine's T (hand check: 385.1/7 = 55.0 m/d)
- Passa cleared Δs is refused rather than giving T ≈ 1e11 (the measured failure of the old floor)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
quick-condition-web-validationquick-condition — validation of the critical hydraulic gradient, exit gradient and factor of safety against heave/boiling against PUBLISHED worked examples and tables.17 passing
Analyses validated: quick-condition
- PassHoltz & Kovacs 1981 Table 7-1: dense sand e = 0.5, Gs = 2.68 → i_c = 1.12
- PassHoltz & Kovacs 1981 Table 7-1: medium sand e = 0.75, Gs = 2.68 → i_c = 0.96
- PassHoltz & Kovacs 1981 Table 7-1: loose sand e = 1, Gs = 2.68 → i_c = 0.84
- PassHoltz & Kovacs 1981 Ex 7.13: Gs = 2.65, e = 0.65 → i_c = 1.0
- PassHoltz & Kovacs 1981 Ex 7.13: a head of 5.0 m over the 5 m sample is exactly the quick condition (FoS = 1)
- PassHoltz & Kovacs 1981 Ex 7.13: the engine calls i = i_c a quick condition (effective stress is zero there)
- PassHoltz & Kovacs 1981 Ex 7.14: seepage force per unit volume at quick conditions j = 9.81 kN/m³
- PassHoltz & Kovacs 1981 Ex 7.19: exit gradient = (12/10.4)/8.5 = 0.14, "not critical"
- PassLambe & Whitman 1969 Ex 18.1: sheet pile, Δh = 7.5/8 m over l = 3.45 m → exit gradient 0.27
- PassLambe & Whitman 1969 Ex 18.2: concrete dam, Δh = 7.8/12.6 m over l = 3.3 m → gradient in square X = 0.19
- PassLambe & Whitman 1969 Ex 18.4: earth dam, Δh = 12/9 m over l = 3.36 m → gradient in square I = 0.40
- PassCraig 2012 Ex 3.4: γsat = 20 kN/m³ → γ′ = 10.2 kN/m³ and i_cr = 1.04
- PassCraig 2012 Ex 3.4: h_m = 2.6 m over 6 m → average gradient i_m = 0.43 and F = 2.4
- PassBond et al. 2013 EC7 A.6.2: h_r = 2.13 m over t = 6.60 m → gradient 0.32
- PassBond et al. 2013 EC7 A.6.2: γ′ = 10 kN/m³ when i_cr = 1 and γw = 10 kN/m³
- PassDas 2016 §15.8: FoS = 1.5 is where the engine stops calling the state marginal
- Passa cleared seepage length is refused, not floored to 1e-9 m
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
seepage-fe-mesh-web-validationWeb-benchmark validation for the TerraCore general-mesh 2-D seepage FE (`seepage-fe-mesh.ts`).7 passing
Analyses validated: mesh-viewer, seepage
- Pass1-D confined: linear head, Darcy q and velocity (Harr §2, Das Ch.8)
- Passconfined discharge scales linearly with k (Darcy)
- Passanisotropic ky does not change purely horizontal discharge
- Pass1-D confined on an unstructured Delaunay mesh reproduces the linear field
- Passflow-net: Q/(k·Δh) equals the shape factor N_f/N_d = H/L (Cedergren §4)
- PassThiem radial: logarithmic head + Q_θ = θ·k·Δh/ln(R/r_w) (Thiem 1906, Harr §5)
- Passunconfined dam section: q = (k/2L)(h1²−h2²) (Dupuit 1863 / Charny 1951, Harr §2.6)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
seepage-web-validationFormula-fidelity validation against Terzaghi & Peck; Das, "Principles of Geotechnical Engineering" Sec.7-8; Casagrande (1937) transformed-section method; Thiem (1906) and Dupuit (1863) steady-state well-flow theory; Sichardt's empirical ra…12 passing
Analyses validated: seepage
- Pass[1] flow-net discharge q = k.H.(Nf/Nd): k=1e-5 m/s, H=5m, Nf=6, Nd=12 -> q=2.5e-5 m3/s per unit width
- Pass[2] critical hydraulic gradient ic = (Gs-1)/(1+e): Gs=2.65, e=0.6 -> ic=1.031250
- Pass[3] piping factor of safety FoS = ic/i_exit: ic=1.03, i_exit=0.5 -> FoS=2.06
- Pass[4] Thiem (1906) confined well discharge Q = 2.pi.T.s/ln(R/rw): k=1e-5, b=10m, s=3m, R=200m, rw=0.15m -> Q=2.619654e-4 m3/s
- Pass[5] Dupuit (1863) unconfined well discharge Q = pi.k.(H^2-hw^2)/ln(R/rw): k=1e-5, H=15m, hw=8m, R=200m, rw=0.15m -> Q=7.029405e-4 m3/s
- Pass[6] Sichardt empirical radius of influence R = 3000.s.sqrt(k): s=3m, k=1e-5 m/s -> R=28.460499m
- Pass[7] Casagrande equivalent isotropic permeability k_eq = sqrt(kx.ky): kx=2e-5, ky=8e-6 -> k_eq=1.264911e-5 m/s
- Pass[8] Casagrande transformed-section horizontal scale factor = sqrt(ky/kx): kx=2e-5, ky=8e-6 -> scale=0.632456
- Pass[9] critical gradient at the exact physical boundary (Gs=1 or e undefined) returns NaN, never a fabricated finite number
- Pass[10] piping FoS at zero exit gradient returns Infinity (no upward flow, no piping risk), not a divide-by-zero NaN
- Pass[11] Thiem discharge scales exactly linearly with drawdown s, per the closed-form (Q proportional to s)
- Pass[12] invalid inputs throw rather than returning a silently-fabricated number (Nd<=0, kx/ky<=0)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
transient-seepage-web-validationValidation for the transient unsaturated-seepage (Richards) engine (`transient-seepage.ts`).12 passing
Analyses validated: transient-seepage
- PassCelia-Bouloutas-Zarba (1990) benchmark θ(ψ) — the canonical Richards test soil
- Passvan Genuchten SWCC + Mualem K anchors
- Passmass is conserved (Celia et al. 1990): infiltration = Δstorage + drainage
- Passa wetting front advances monotonically under infiltration
- Passthe surface wets toward θs under infiltration; θ stays within [θr, θs]
- Passunit-gradient steady state: drainage rate → applied flux (q < Ks)
- Passponded-head top BC infiltrates faster than a small flux; input validation
- Passaudit: a fully non-converged solve is REFUSED, not reported from the imposed flux
- Passaudit: K_s far outside any real soil is refused before the solve even runs
- Passaudit: an implausible infiltration flux is refused before the solve
- Passaudit: a refused run is NaN, not 0 — the client renders "—", not "0.0 mm"
- Passaudit: the real, valid case is unaffected by the new bounds
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
unconfined-seepage-web-validationC.FE.3 — FE unconfined (free-surface / phreatic) seepage web-benchmark.6 passing
Analyses validated: fe-seepage, unconfined-seepage
- PassC.FE.3: FE discharge matches the exact Dupuit q within 8%
- PassC.FE.3: phreatic line follows the Dupuit parabola h(x)²=h1²−(h1²−h2²)x/L
- PassC.FE.3: free surface starts at h1 upstream and is monotonically falling
- PassC.FE.3: discharge scales linearly with k and quadratically with head
- PassC.FE.3: near-equal reservoir levels → near-zero discharge
- PassC.FE.3: input guards return clean errors, not NaN/crash
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Heat transfer, freezing and solute transport
18 finite-element rows · 0 closed-form problems · 1 validation suites
Finite-element solver registry
Showing 18 of 18 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
T(0.5, 0.5), square plate 100 / 500 °C k9-rs2-plate-centre | 200°C | 200°C | 0.00 % | Ours 200 °CPublished 200 °C0.00 % | Pass | |
| ||||||
T(0.5, 0.75) k9-rs2-plate-0.5-0.75 | 316.212°C | 316.212°C | 0.00 % | Ours 316.212 °CPublished 316.212 °C0.00 % | Pass | |
| ||||||
T(0, 1), unit flux into a rod k9-rs2-rod-x0 | 1.12833°C | 1.12838°C | −4.4e-3 % | Ours 1.12833 °CPublished 1.12838 °C−4.4e-3 % | Pass | |
| ||||||
T(1, 1) k9-rs2-rod-x1 | 0.39928°C | 0.39928°C | 0.00 % | Ours 0.39928 °CPublished 0.39928 °C0.00 % | Pass | |
| ||||||
T(2, 1) k9-rs2-rod-x2 | 0.10051°C | 0.10051°C | 0.00 % | Ours 0.10051 °CPublished 0.10051 °C0.00 % | Pass | |
| ||||||
surface T after 1 h (h 40, T∞ −15, from 20 °C) k9-rs2-convective-1h | -4.8506°C | -4.8568°C | +0.13 % | Ours -4.8506 °CPublished -4.8568 °C+0.13 % | Pass | |
| ||||||
surface T after 1 day k9-rs2-convective-1d | -12.6634°C | -12.6642°C | +6.3e-3 % | Ours -12.6634 °CPublished -12.6642 °C+6.3e-3 % | Pass | |
| ||||||
T_E, NAFEMS T4 (steady, convection) k9-nafems-t4 | 18.2558°C | 18.3°C | −0.24 % | Ours 18.2558 °CPublished 18.3 °C−0.24 % | Pass | |
| ||||||
T_C(32 s), harmonic end temperature 100 sin(πt/40) k9-nafems-t3 | 36.6029°C | 36.6°C | +7.9e-3 % | Ours 36.6029 °CPublished 36.6 °C+7.9e-3 % | Pass | |
| ||||||
T_C(58 s), Barlow & Davis 1987 k9-barlow-davis | 9.6095°C | 9.62°C | −0.11 % | Ours 9.6095 °CPublished 9.62 °C−0.11 % | Pass | |
| ||||||
Péclet number N_PE = C_w q L / λ k9-rs2-forced-convection-npe | 4.186 | 4.186 | 0.00 % | Ours 4.186Published 4.1860.00 % | Pass | |
| ||||||
T(0.05 m), downward flow k9-rs2-forced-convection-down-y0.05 | 0.51001°C | 0.51001°C | 0.00 % | Ours 0.51001 °CPublished 0.51001 °C0.00 % | Pass | |
| ||||||
T(0.25 m), upward flow k9-rs2-forced-convection-up-y0.25 | 0.48999°C | 0.48999°C | 0.00 % | Ours 0.48999 °CPublished 0.48999 °C0.00 % | Pass | |
| ||||||
thaw front after 100 days k9-neumann-front-100d | 0.3748m | 0.3748m | 0.00 % | Ours 0.3748 mPublished 0.3748 m0.00 % | Pass | |
| ||||||
thaw front after 10 days k9-neumann-front-10d | 0.1186m | 0.1185m | +0.08 % | Ours 0.1186 mPublished 0.1185 m+0.08 % | Pass | |
| ||||||
heat flow through a hollow cylinder (axisymmetric, per radian) k9-hollow-cylinder-q | 11.6769W/rad | 11.6769W/rad | 0.00 % | Ours 11.6769 W/radPublished 11.6769 W/rad0.00 % | Pass | |
| ||||||
c/c0 at 1.2 m after 3 days (v 0.4 m/d, D 0.0041 m²/d) k9-ogata-banks-x1.2-t3 | 0.5256 | 0.526 | −0.08 % | Ours 0.5256Published 0.526−0.08 % | Pass | |
| ||||||
c/c0 at 0.4 m after 4 days (R 2.6, t½ 2 d) k9-vga-retarded-decay-x0.4-t4 | 0.4096 | 0.4097 | −0.02 % | Ours 0.4096Published 0.4097−0.02 % | Pass | |
| ||||||
Cited validation suites
unsaturated-thermal-web-validationWeb-validation for the unsaturated-soil + thermal (THM) engine (`unsaturated-thermal.ts`).23 passing
Analyses validated: unsaturated-thermal
- Passvan Genuchten: Se(ψ=0)=1 and θ(ψ=0)=θ_s (van Genuchten 1980, Eq. 3)
- Passvan Genuchten: Se→0 and θ→θ_r as ψ→∞ (van Genuchten 1980)
- Passvan Genuchten: Se strictly decreasing in suction (van Genuchten 1980)
- Passvan Genuchten m = 1 − 1/n for n=2, 4, 1.5 (van Genuchten 1980, m-n constraint)
- Passvan Genuchten: at αψ=1, Se = 2^(−m) exactly (van Genuchten 1980, Eq. 3)
- Passvan Genuchten: θ at αψ=1, n=2 = θ_r + 2^(−0.5)(θ_s−θ_r) = 0.332843 (van Genuchten 1980)
- Passvan Genuchten 1980 Table 1 — Guelph Loam (α=0.0115, n=2.03, θs=0.520, θr=0.218)
- Passvan Genuchten 1980 Table 1 — Beit Netofa Clay (α=0.00152, n=1.17, θs=0.446, θr=0.0)
- Passvan Genuchten 1980 Table 1 — Hygiene Sandstone (α=0.0079, n=10.4): sharp air-entry
- PassBishop 1959: χ = Se exactly (χ=1 saturated, χ=0 dry)
- PassBishop 1959: net normal stress (σ−u_a) and u_w = u_a − ψ
- PassBishop 1959: σ′ = (σ−u_a)+Se·ψ anchor = 270.7107 kPa (αψ=1, n=2, σ=200)
- PassBishop 1959: σ′ (suction stress Se·ψ) increases with suction over the working range
- PassVanapalli 1996: apparent cohesion c_app = ψ·Se·tanφ′ anchor = 40.825 kPa
- PassVanapalli 1996: c_app == ψ·Se·tanφ′ holds for arbitrary state
- PassVanapalli 1996: total cohesion = c′ + c_app; τ = c′ + (σ−u_a)tanφ′ + c_app
- PassVanapalli 1996: unsaturated τ ≤ saturated τ (χ=Se≤1); equal only at ψ=0
- PassCarslaw & Jaeger §2.5: erfc argument z/(2√(D_th·t)) and surface value
- PassCarslaw & Jaeger §2.5: erfc(z/2) matches standard table at arg=0.5, 1, 2
- PassCarslaw & Jaeger §2.5: t=0 interior unchanged; t→∞ whole profile reaches T_s
- PassLinear thermal strain ε = α_T·ΔT — sign and magnitude
- Passguards: pathological inputs are REFUSED, not clamped into a plausible answer
- Passunsaturated-thermal: the real physical limits stay LEGAL and self-consistent
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Earthquake engineering, dynamics and liquefaction
69 finite-element rows (3 deviations) · 0 closed-form problems · 32 validation suites
Finite-element solver registry
Showing 69 of 69 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
Rayleigh αR for ξ = 8 % at 1.5 and 7.5 Hz k7a-rayleigh-alpha-ground-response | 1.256641/s | 1.256641/s | 0.00 % | Ours 1.25664 1/sPublished 1.25664 1/s0.00 % | Pass | |
| ||||||
Rayleigh βR for ξ = 8 % at 1.5 and 7.5 Hz k7a-rayleigh-beta-ground-response | 0.00282942s | 0.00282942s | 0.00 % | Ours 0.00282942 sPublished 0.00282942 s0.00 % | Pass | |
| ||||||
Rayleigh αR for ξ = 3 % at 1.751 and 3.0 Hz k7a-rayleigh-alpha-footing | 0.4168251/s | 0.4168251/s | 0.00 % | Ours 0.416825 1/sPublished 0.416825 1/s0.00 % | Pass | |
| ||||||
Rayleigh βR for ξ = 3 % at 1.751 and 3.0 Hz k7a-rayleigh-beta-footing | 0.00200995s | 0.00200995s | 0.00 % | Ours 0.00200995 sPublished 0.00200995 s0.00 % | Pass | |
| ||||||
time the front reaches point B (5 m below the top; u_B = 0.5 mm) k7a-1d-wave-arrival-middle | 0.05072s | 0.05s | +1.44 % | Ours 0.05072 sPublished 0.05 s+1.44 % | Pass | |
| ||||||
mean u_B between the arrival and the return of the reflection (0.07–0.13 s) k7a-1d-wave-plateau-fixed-base · Self-check | -0.0010001m | -0.001m | −0.01 % | Ours -0.0010001 mPublished -0.001 m−0.01 % | Pass | |
| ||||||
mean u_B after the reflection from the fixed base has passed (0.17–0.23 s) k7a-1d-wave-after-reflection-fixed-base | -2.274e-8m | 0m | — | Ours -2.274e-8 mPublished 0 m— | Pass | |
| ||||||
time the front reaches the base (point A, 10 m) with a viscous base k7a-1d-wave-arrival-base-viscous | 0.10083s | 0.1s | +0.83 % | Ours 0.10083 sPublished 0.1 s+0.83 % | Pass | |
| ||||||
reflection at the viscous base: |mean u_B(0.17–0.25 s) + 1 mm| / 1 mm k7a-1d-wave-absorbing-reflection | 0% | 0% | — | Ours 0 %Published 0 %— | Pass | |
| ||||||
model B through the ModelSpec route (kernel mesher, very_fine T15): arrival at the base k7a-1d-wave-spec-mesher | 0.10083s | 0.1s | +0.83 % | Ours 0.10083 sPublished 0.1 s+0.83 % | Pass | |
| ||||||
first natural frequency of the 50 m layer (free vibration after a static top shear is removed; DFT peak) k7a-shear-column-f0 | 1.49956Hz | 1.50006Hz | −0.03 % | Ours 1.49956 HzPublished 1.50006 Hz−0.03 % | Pass | |
| ||||||
amplification |a_top / a_base| at 0.75 Hz, rigid base, Rayleigh ξ = 8 % (1.5 / 7.5 Hz) k7a-ground-response-rigid-0p75hz | 1.4058 | 1.406 | −0.01 % | Ours 1.4058Published 1.406−0.01 % | Pass | |
| ||||||
amplification |a_top / a_base| at 1.5 Hz, rigid base, Rayleigh ξ = 8 % (1.5 / 7.5 Hz) k7a-ground-response-rigid-1p5hz | 7.9467 | 7.9506 | −0.05 % | Ours 7.9467Published 7.9506−0.05 % | Pass | |
| ||||||
amplification |a_top / a_base| at 3.0 Hz, rigid base, Rayleigh ξ = 8 % (1.5 / 7.5 Hz) k7a-ground-response-rigid-3p0hz | 0.9826 | 0.9826 | 0.00 % | Ours 0.9826Published 0.98260.00 % | Pass | |
| ||||||
amplification |a_top / a_base| at 4.5 Hz, rigid base, Rayleigh ξ = 8 % (1.5 / 7.5 Hz) k7a-ground-response-rigid-4p5hz | 3.3665 | 3.3698 | −0.10 % | Ours 3.3665Published 3.3698−0.10 % | Pass | |
| ||||||
amplification |v_top / v_outcrop| at 0.75 Hz on elastic rock (Vr = 2 Vs, ρr = ρ), outcrop velocity input k7a-ground-response-elastic-rock-0p75hz | 1.1083 | 1.1086 | −0.03 % | Ours 1.1083Published 1.1086−0.03 % | Pass | |
| ||||||
amplification |v_top / v_outcrop| at 1.5 Hz on elastic rock (Vr = 2 Vs, ρr = ρ), outcrop velocity input k7a-ground-response-elastic-rock-1p5hz | 1.5816 | 1.5827 | −0.07 % | Ours 1.5816Published 1.5827−0.07 % | Pass | |
| ||||||
amplification |v_top / v_outcrop| at 4.5 Hz on elastic rock (Vr = 2 Vs, ρr = ρ), outcrop velocity input k7a-ground-response-elastic-rock-4p5hz | 1.2208 | 1.2211 | −0.02 % | Ours 1.2208Published 1.2211−0.02 % | Pass | |
| ||||||
mid-span deflection under q = 1 kN/m/m (static phase before the free vibration) k7a-beam-static-deflection | 0.13023m | 0.130208m | +0.02 % | Ours 0.13023 mPublished 0.130208 m+0.02 % | Pass | |
| ||||||
first natural frequency of the simply supported beam (free vibration after the load is removed) k7a-beam-natural-frequency | 1.56976Hz | 1.5708Hz | −0.07 % | Ours 1.56976 HzPublished 1.5708 Hz−0.07 % | Pass | |
| ||||||
onset of the P wave at r = 50 m (2 % of the peak) k7a-lamb-p-onset | 0.3311s | 0.3415s | −3.05 % | Ours 0.3311 sPublished 0.3415 s−3.05 % | Pass | |
| ||||||
time of the Rayleigh-wave (negative) peak of uy at r = 50 m k7a-lamb-rayleigh-peak-time | 0.63s | 0.6116s | +3.01 % | Ours 0.63 sPublished 0.6116 s+3.01 % | Pass | |
| ||||||
Rayleigh-wave peak of uy at r = 50 m k7a-lamb-rayleigh-peak-amplitude | -0.00987mm | -0.01mm | +1.30 % | Ours -0.00987 mmPublished -0.01 mm+1.30 % | Pass | |
| ||||||
max |τ| at a base stress point of a φ = 0 Mohr–Coulomb column shaken beyond its strength (c = 250 kPa) k7a-elastoplastic-yield · Self-check | 250kPa | 250kPa | 0.00 % | Ours 250 kPaPublished 250 kPa0.00 % | Pass | |
| ||||||
HHT-α with α = 0 vs Newmark average acceleration k7a-hht-zero-is-newmark · Self-check | 0 | 0 | — | Ours 0Published 0— | Pass | |
| ||||||
first two natural frequencies of a dam with depth-varying G (PLAXIS 2.9 / 6.4 Hz; closed form 3.1 / 7.0 Hz) k7a-dam-free-vibration | —Hz | 3.1Hz | — | Ours — HzPublished 3.1 Hz— | Pending | |
| ||||||
surface deflection under a pulse load on a 3-layer pavement (stiff / soft subgrade) k7a-pulse-multilayer | —mm | —mm | — | Ours — mmPublished — mm— | Pending | |
| ||||||
vertical dynamic stiffness K_v = F πR² / w_max of the rigid circular footing (plate in a dynamic phase, D185) k7a-vertical-footing-dynamic | 2363810kN/m | 2335570kN/m | +1.21 % | Ours 2363810 kN/mPublished 2335570 kN/m+1.21 % | Pass | |
| ||||||
surface-wave amplitude vs distance from a harmonic prescribed displacement (BEM Chouw et al. 1991) k7a-surface-waves | —m | —m | — | Ours — mPublished — m— | Pending | |
| ||||||
Midas GTS NX dynamics benchmarks k7a-midas-ch4-dynamics | — | — | — | Ours —Published —— | Pending | |
| ||||||
w_max under the footing centre (point A) k7b-vertical-footing-wmax | 53.161mm | 53.8mm | −1.19 % | Ours 53.161 mmPublished 53.8 mm−1.19 % | Pass | |
| ||||||
static midspan deflection under q = 1 kN/m/m — a real PLATE (K7a used a continuum substitute) k7b-plate-beam-deflection | 0.13023m | 0.130208m | +0.02 % | Ours 0.13023 mPublished 0.130208 m+0.02 % | Pass | |
| ||||||
first natural frequency — plate mass w/g with rotary inertia (consistent and HRZ-lumped) k7b-plate-beam-frequency | 1.56976Hz | 1.5708Hz | −0.07 % | Ours 1.56976 HzPublished 1.5708 Hz−0.07 % | Pass | |
| ||||||
excess pore pressure behind a step-load P front, undrained A (ν_u 0.495) k7b-undrained-p-wave-excess | 9.7364kPa | 9.736kPa | +4.1e-3 % | Ours 9.7364 kPaPublished 9.736 kPa+4.1e-3 % | Pass | |
| ||||||
arrival of half the undrained front at 5 m k7b-undrained-p-wave-arrival | 0.00825s | 0.0081245s | +1.54 % | Ours 0.00825 sPublished 0.0081245 s+1.54 % | Pass | |
| ||||||
rigid-base amplification at 0.75 Hz with TIED side DOFs (D186) k7b-tied-column-0.75hz | 1.4058 | 1.406 | −0.01 % | Ours 1.4058Published 1.406−0.01 % | Pass | |
| ||||||
rigid-base amplification at 1.5 Hz with TIED side DOFs (D186) k7b-tied-column-1.5hz | 7.9467 | 7.9506 | −0.05 % | Ours 7.9467Published 7.9506−0.05 % | Pass | |
| ||||||
rigid-base amplification at 3.0 Hz with TIED side DOFs (D186) k7b-tied-column-3.0hz | 0.9826 | 0.9826 | 0.00 % | Ours 0.9826Published 0.98260.00 % | Pass | |
| ||||||
rigid-base amplification at 4.5 Hz with TIED side DOFs (D186) k7b-tied-column-4.5hz | 3.3665 | 3.3698 | −0.10 % | Ours 3.3665Published 3.3698−0.10 % | Pass | |
| ||||||
amplification with FREE-FIELD sides (D186): rigid base 1.5 Hz, centre k7b-free-field-rigid-1p5 | 7.9718 | 7.9506 | +0.27 % | Ours 7.9718Published 7.9506+0.27 % | Pass | |
| ||||||
amplification with FREE-FIELD sides (D186): rigid base 3 Hz, centre k7b-free-field-rigid-3 | 0.9968 | 0.9826 | +1.45 % | Ours 0.9968Published 0.9826+1.45 % | Pass | |
| ||||||
amplification with FREE-FIELD sides (D186): elastic rock (compliant base) 1.5 Hz, centre k7b-free-field-rock-1p5 | 1.5873 | 1.5827 | +0.29 % | Ours 1.5873Published 1.5827+0.29 % | Pass | |
| ||||||
linear baseline coefficient c0 (v_c(T) = u_c(T) = 0) k7b-baseline-closed-form | 0.233801m/s² | 0.233803m/s² | −6.0e-4 % | Ours 0.233801 m/s²Published 0.233803 m/s²−6.0e-4 % | Pass | |
| ||||||
PGA of the El Centro 1940 ELC-180 record through the ground-motion registry (DY-5) k7b-elc180-pga | 0.312881g | 0.313g | −0.04 % | Ours 0.312881 gPublished 0.313 g−0.04 % | Pass | |
| ||||||
absolute base displacement at the end of the record, drift-corrected k7b-elc180-base-drift · Self-check | -1.990e-13m | 0m | — | Ours -1.990e-13 mPublished 0 m— | Pass | |
| ||||||
CRR at 15 uniform cycles (3 % single-amplitude shear strain), undrained cyclic DSS, Dr 0.35, G0 476, hpo 0.53 k7b-pm4sand-crr15-dr35 | 0.0874 | 0.09 | −2.80 % | Ours 0.0874Published 0.09−2.80 % | Pass | |
| ||||||
CRR at 15 uniform cycles (3 % single-amplitude shear strain), undrained cyclic DSS, Dr 0.55, G0 677, hpo 0.4 k7b-pm4sand-crr15-dr55 | 0.142 | 0.147 | −3.40 % | Ours 0.142Published 0.147−3.40 % | Pass | |
| ||||||
CRR at 15 uniform cycles (3 % single-amplitude shear strain), undrained cyclic DSS, Dr 0.75, G0 890, hpo 0.63 k7b-pm4sand-crr15-dr75 | 0.2948 | 0.312 | −5.50 % | Ours 0.2948Published 0.312−5.50 % | Pass | |
| ||||||
slope b of CSR ∝ N^−b, Dr 0.35 k7b-pm4sand-csr-n-slope-dr35 | 0.241 | 0.25 | +12.8 % | Ours 0.241Published 0.25+12.8 % | Pass | |
| ||||||
slope b of CSR ∝ N^−b, Dr 0.55 k7b-pm4sand-csr-n-slope-dr55 | 0.279 | 0.29 | +1.03 % | Ours 0.279Published 0.29+1.03 % | Pass | |
| ||||||
slope b of CSR ∝ N^−b, Dr 0.75 k7b-pm4sand-csr-n-slope-dr75 | 0.286 | 0.3 | −12.7 % | Ours 0.286Published 0.3−12.7 % | Pass | |
| ||||||
peak φ′DSS, drained monotonic DSS at 1 atm, Dr 0.35 k7b-pm4sand-drained-phi-dr35 | 29.81° | 30° | −0.63 % | Ours 29.81 °Published 30 °−0.63 % | Pass | |
| ||||||
peak φ′DSS, drained monotonic DSS at 1 atm, Dr 0.55 k7b-pm4sand-drained-phi-dr55 | 33.3° | 33.5° | −0.60 % | Ours 33.3 °Published 33.5 °−0.60 % | Pass | |
| ||||||
peak φ′DSS, drained monotonic DSS at 1 atm, Dr 0.75 k7b-pm4sand-drained-phi-dr75 | 37.42° | 37.7° | −0.74 % | Ours 37.42 °Published 37.7 °−0.74 % | Pass | |
| ||||||
max r_u = Δp/σ′v0 at 4 m and 7 m depth k7b-liquefaction-column-ru · Self-check | 4 m: 0.8024; 7 m: 1.0311 | 0.95 | — | Ours 4 m: 0.8024; 7 m: 1.0311Published 0.95— | Deviation | |
| ||||||
steady vertical displacement amplitude at the surface point r = 1.37 m, without Rayleigh damping (Fig. 15-9) k7-plaxis-2d-tut15-surface-1.37-undamped | 0.0336mm | 0.0339mm | −0.80 % | Ours 0.0336 mmPublished 0.0339 mm−0.80 % | Pass | |
| ||||||
steady vertical displacement amplitude at the surface point r = 1.94 m, without Rayleigh damping (Fig. 15-9) k7-plaxis-2d-tut15-surface-1.94-undamped | 0.0239mm | 0.0236mm | +1.20 % | Ours 0.0239 mmPublished 0.0236 mm+1.20 % | Pass | |
| ||||||
steady vertical displacement amplitude at the surface point r = 3.60 m, without Rayleigh damping (Fig. 15-9) k7-plaxis-2d-tut15-surface-3.60-undamped | 0.0141mm | 0.0138mm | +1.90 % | Ours 0.0141 mmPublished 0.0138 mm+1.90 % | Pass | |
| ||||||
steady vertical displacement amplitude at the surface point r = 1.37 m, with Rayleigh damping (Fig. 15-10) k7-plaxis-2d-tut15-surface-1.37-damped | 0.0319mm | 0.0322mm | −0.90 % | Ours 0.0319 mmPublished 0.0322 mm−0.90 % | Pass | |
| ||||||
steady vertical displacement amplitude at the surface point r = 1.94 m, with Rayleigh damping (Fig. 15-10) k7-plaxis-2d-tut15-surface-1.94-damped | 0.0222mm | 0.022mm | +0.90 % | Ours 0.0222 mmPublished 0.022 mm+0.90 % | Pass | |
| ||||||
steady vertical displacement amplitude at the surface point r = 3.60 m, with Rayleigh damping (Fig. 15-10) k7-plaxis-2d-tut15-surface-3.60-damped | 0.012mm | 0.0116mm | +3.10 % | Ours 0.012 mmPublished 0.0116 mm+3.10 % | Pass | |
| ||||||
steady vertical displacement amplitude of the rigid footing (axis), mass = the plate only (the manual's static generator load carries no mass), B = m(1−ν)/(4ρR³) = 0.275 k7-plaxis-2d-tut15-footing-lysmer-analog | 0.136mm | 0.1416mm | −3.99 % | Ours 0.136 mmPublished 0.1416 mm−3.99 % | Pass | |
| ||||||
steady vertical displacement amplitude of the rigid footing (axis) carrying the generator mass too, B = 0.715 k7-plaxis-2d-tut15-footing-lysmer-analog-with-generator-mass | 0.142mm | 0.1481mm | −4.11 % | Ours 0.142 mmPublished 0.1481 mm−4.11 % | Pass | |
| ||||||
absorbing-boundary reflection error: largest change of the steady amplitude (4 points) when the model is doubled from 20 × 10 m (the manual) to 40 × 20 m k7-plaxis-2d-tut15-boundary-distance-20x10-vs-40x20 | 2.76% | 0% | — | Ours 2.76 %Published 0 %— | Pass | |
| ||||||
absorbing-boundary reflection error: largest change of the steady amplitude (4 points) when the model is halved from 20 × 10 m to 10 × 5 m, against the 40 × 20 m model k7-plaxis-2d-tut15-boundary-distance-10x5-vs-40x20 | 4.6% | 0% | — | Ours 4.6 %Published 0 %— | Pass | |
| ||||||
residual surface displacement after the generator stops, r = 1.37 m, no damping (amplitude over 0.6–1.0 s) k7-plaxis-2d-tut15-free-vibration-residual-undamped | 0.00531mm | 0.0034mm | +56.2 % | Ours 0.00531 mmPublished 0.0034 mm+56.2 % | Deviation | |
| ||||||
residual surface displacement after the generator stops, r = 1.37 m, with Rayleigh damping (amplitude over 0.6–1.0 s) k7-plaxis-2d-tut15-free-vibration-residual-damped | 0.00313mm | 0.0008mm | +291.3 % | Ours 0.00313 mmPublished 0.0008 mm+291.3 % | Deviation | |
| ||||||
Rayleigh α from ξ1 = ξ2 = 5 % at f1 = 1 Hz, f2 = 10 Hz (SDOF equivalent, Fig. 15-8) k7-plaxis-2d-tut15-rayleigh-alpha | 0.5711991/s | 0.57121/s | 0.00 % | Ours 0.571199 1/sPublished 0.5712 1/s0.00 % | Pass | |
| ||||||
Rayleigh β from ξ1 = ξ2 = 5 % at f1 = 1 Hz, f2 = 10 Hz (SDOF equivalent, Fig. 15-8) k7-plaxis-2d-tut15-rayleigh-beta | 0.0014469s | 0.001447s | −9.0e-3 % | Ours 0.0014469 sPublished 0.001447 s−9.0e-3 % | Pass | |
| ||||||
Cited validation suites
cpt-liquefaction-web-validationValidation for the CPT liquefaction-triggering engine (`cpt-liquefaction.ts`).24 passing
Analyses validated: cpt-liquefaction
- PassTable 3.1 — 1964 Niigata, D Kawagisho-cho — clean sand (FC 3 %), z 4.4 m, M 7.6
- PassTable 3.1 — 1968 Inangahua, Three Channel Flat — silty sand (FC 18 %), N_c cap region (CN 1.55)
- PassTable 3.1 — 1981 Westmorland, Kornbloom Rd (K4) — very high fines (FC 85 %), M 5.9
- PassTable 3.1 — 1989 Loma Prieta, Sandhold Road SI-2 — very dense sand, q_c1N,cs 311.9 > 211 (cap region)
- PassTable 3.1 — 1995 Hyogoken-Nambu, Fukuzumi Park — deepest case (11.8 m), K_σ < 1
- PassTable 3.1 — 1994 Northridge, Balboa Blvd Unit C (BAL-10) — highest σ′_v (147 kPa), FC 50 %
- PassTable 3.1 — 2011 Tohoku, Hinode ES — M 9.0, FC 25 %, K_σ at its 1.10 cap
- PassTable 3.1 — 1995 Hyogoken-Nambu, Yoshida Kogyo Factory — q_c1N,cs 216 just above 211, K_σ at 1.10 cap
- PassTable 3.1 — 1999 Kocaeli, Hotel Sapanca SH-4 — lowest σ′_v (19 kPa): C_N capped at 1.70
- PassTable 3.1 — 1989 Loma Prieta, Marine Lab (C4) — loose clean sand q_c1N,cs 24.4 (m-limit region)
- PassTable 3.1 — 1981 Westmorland, McKim Ranch Unit A (M7) — smallest M (5.9), MSF 1.12
- PassTable 3.1 — 2011 Tohoku, Akemi ES — M 9.0, 10.1 m, σ′_v ~ 1 atm
- PassMNO-12 App. B row 47 — z 1.80 m (water table), q_cN 26.5, σ 34/34 kPa
- PassMNO-12 App. B row 49 — z 1.90 m, q_cN 34.0, σ 36/35 kPa
- PassMNO-12 App. B row 51 — z 2.00 m, q_cN 39.6, σ 38/36 kPa
- PassMNO-12 App. B row 53 — z 2.10 m, q_cN 45.1, σ 40/37 kPa
- PassMNO-12 App. B row 166 — z 7.75 m, q_cN 150.5, σ 153/95 kPa (C_N below 1.7)
- PassMNO-12 App. B row 168 — z 7.85 m, q_cN 112.3, σ 155/96 kPa
- PassMNO-12 App. B row 170 — z 7.95 m, q_cN 81.8, σ 157/97 kPa
- PassMNO-12 App. B row 175 — z 8.20 m, q_cN 120.0, σ 162/99 kPa
- Pass§2.5 printed statement: MSF_max = 1.8 at q_c1Ncs ≈ 160
- Pass§2.5 printed statement: MSF_max ≈ 1.10 for q_c1Ncs < 60 (loose sands)
- PassB&I 2014 §4.1 counts: 253 cases; 5 liquefaction points below and 32 no-liquefaction points above the deterministic curve
- PassHAND-DERIVED: deterministic CRR = median (C0 = 2.60) CRR × exp(−0.20), i.e. one σ_lnR below the median
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
design-code-spectrum-ec8-web-validationEN 1998-1 (Eurocode 8) horizontal elastic response spectrum — anchored to the standard and to a published European worked example.11 passing
Analyses validated: design-code-spectrum
- PassEN 1998-1 Table 3.2 (Type 1): S, TB, TC, TD reproduced for ground types A-E
- PassEN 1998-1 Table 3.3 (Type 2): S, TB, TC, TD reproduced for ground types A-E
- PassEC8 worked example §2.1.2.1: ground B, Type 1, agR = 0.25g, γI = 1.0 ⇒ plateau 0.75 g
- PassEC8 worked example: the design spectrum with q = 3.0 is the elastic one divided by q on the plateau
- PassE-38: Type 1 UNDER-predicts the Type 2 plateau on every ground type except A
- PassE-38: the two shapes really are different curves, not a scale factor
- PassEN 1998-1 Table 3.1: Vs30 bands A > 800, B 360-800, C 180-360, D < 180
- PassE-39: ground type E is unreachable from Vs30 and must be selectable explicitly
- Passthe spectrum is continuous at TB, TC and TD for both shapes and all ground types
- Passdefaults are unchanged: no spectrum_type ⇒ Type 1, and ag defaults to 0.25 g
- Passa negative or absent ag is clamped, and Sa stays finite everywhere
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
design-code-spectrum-web-validationWEB-BENCHMARK validation for the shared design-code-spectrum module and the 2-D site-response CODE-SITE-FACTOR overlay (`fe-site-response-2d`).17 passing
Analyses validated: design-code-spectrum, fe-site-response-2d
- Passdcs 1: EC8 class C / rock A at T=0.3 s ⇒ S ratio = 1.15/1.0 = 1.15
- Passdcs 2: EC8 class B / rock A at T=0.3 s ⇒ 1.20
- Passdcs 3: EC8 class D / rock A at T=0.3 s ⇒ 1.35
- Passdcs 4: EC8 amplification is independent of a_g (ratio cancels)
- Passdcs 5: ASCE class D / rock A at T=0.3 s, Ss=1.0 ⇒ Fa ratio 1.1/0.8 = 1.375
- Passdcs 6: ASCE class D / rock A at low Ss=0.25 ⇒ Fa 1.6/0.8 = 2.0
- Passdcs 7: ASCE class C / rock A at Ss=1.0 ⇒ Fa 1.2/0.8 = 1.5
- Passdcs 8: IS 1893 short-period (T=0.3 s) soil factor = 1.0 (same 2.5 plateau)
- Passdcs 9: IS 1893 Type II / I at T=0.6 s ⇒ (1.36/0.6)/(1.0/0.6) = 1.36
- Passdcs 10: IS 1893 Type III / I at T=1.0 s ⇒ 1.67 (soft-soil long-period amplification)
- Passdcs 11: softer soil ⇒ higher (or equal) code site factor at a long period
- Passdcs 12: site class strings match the Vs thresholds
- Passdcs 13: rock reference class is the firm-rock class (A / A / I)
- Passdcs 14: 2-D overlay reports site class, code factor and a verdict for each code
- Passdcs 15: a basin (2-D focusing) EXCEEDS the code 1-D site factor (Mexico City lesson)
- Passdcs 16: no overlay fields when seismic_code is omitted (opt-in)
- Passdcs 17: the 2-D overlay uses the SAME code factor as a direct module call
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
dynamic-compaction-web-validationrecords a differenceWeb/published-source validation for `dynamic-compaction.ts` (Ménard dynamic compaction).80 passing
Analyses validated: dynamic-compaction
- Pass[S3-1] Depth of improvement D_i = 0.35·√(18.2·30.2) (m) — S3 §1.2 p.4
- Pass[S3-2] Applied energy, high-energy pass AE_HEP (MJ/m²) — S3 §1.3 p.4
- Pass[S3-3] Applied energy, ironing pass AE_IP (MJ/m²) — S3 §1.3 p.4
- Pass[S3-4] Total applied energy AE_HEP + AE_IP ("~4.02 MJ/m² per pass") — S3 §1.3 p.5
- Pass[S3-5] Improved elastic modulus E = (E/N)·N = 2 × 32.56 (MPa) — S3 §1.5 Eq. 4 p.6
- Pass[S3-6] Crater depth, Rollins–Kim detailed formula (m) "≈ 1.5 m" — S3 §1.6 Eq. 5 p.7
- Pass[S3-7] Area ratio of improvement a_r = 1.767/9 — S3 §1.7 p.7
- Pass[S3-8] Induced settlement S = N_p·a_r·d_cd = 2 × 0.196 × 1.5 (m) — S3 §1.7 Eq. 6 p.7
- Pass[S3-9] Peak particle velocity at 20 m (mm/s) — S3 §1.8 Eq. 7 p.8
- Pass[S3-10] Design total energy = 850 kJ/m³ × 8.2 m = 6.97 MJ/m² (via design mode) — S3 §1.4 p.5
- Pass[S3-11] Required energy per pass, two passes = 6.97/2 = 3.485 MJ/m² — S3 §1.4 p.5
- Pass[HAN-1] Required energy per blow W_t·H_d = (8.2/0.35)² (t·m) — HAN §3.5.5 p.98
- Pass[HAN-2] Required drop height for the 18.2 t tamper = 550/18.2 (m) — HAN §3.5.5 p.98
- Pass[HAN-3] Typical drop height H_d = (W_t·H_d)^0.54 (m) "also 30.2 m" — HAN Eq. 3.17 p.93 / §3.5.5 p.98
- Pass[HAN-4] Total applied energy 850 kJ/m³ × 8.2 m (MJ/m²) — HAN §3.5.5 p.98
- Pass[HAN-5] Ironing energy AE_IP = 300 kJ/m³ × 1.5 m (MJ/m²) — HAN Eq. 3.22, §3.5.5 p.98
- Pass[HAN-6] High-energy total AE_HEP·N_p = 6.97 − 0.45 (MJ/m²) — HAN §3.5.5 p.98
- Pass[HAN-7] Per-pass energy for two passes (MJ/m²) — HAN §3.5.5 p.98
- Pass[HAN-8] Drops per point N_d = 3260·9/(18.2·30.2·10) (Han writes g = 10 m/s²) — HAN Eq. 3.20, §3.5.5 p.98
- Pass[HAN-9] Drops selected = round-up of the requirement (integer), at the engine's default g = 9.81 — HAN §3.5.5 p.98
- Pass[HAN-10] Rough crater depth d_cd = 0.075·√550 (m) — HAN Eq. 3.18 / §3.5.5 p.98
- Pass[HAN-11] Allowable crater depth = tamper height + 0.3 = 1.5 + 0.3 (m) — HAN §3.5.5 p.98
- Pass[HAN-12] Area ratio of improvement π(1.5/2)²/3.0² ("= 0.20") — HAN §3.5.5 p.99
- Pass[HAN-13] Induced settlement, 2 passes: 2 × 0.20 × 1.75 (m) — HAN §3.5.5 p.99
- Pass[HAN-14] Detailed (Rollins–Kim) crater for the same 6 drops, p = 18.2/(π·0.75²) (m) — HAN Eq. 3.19 via S3 §1.6
- Pass[G1-1] Energy per blow for D = 8.2 m, n = 0.35: (8.2/0.35)²·g (MJ) — G1 Ch.7 p.62 (Indiana)
- Pass[G1-2] Energy per blow for the 18.2 Mg tamper dropped 29.9 m (MJ) — G1 Ch.7 p.62 (Indiana)
- Pass[G1-3] Depth of improvement of 18.2 Mg × 29.9 m at n = 0.35 (m) — design target "8.2 m" — G1 Ch.7 p.62 (Indiana)
- Pass[G1-4] Total applied energy 735 kJ/m³ × 8.5 m (MJ/m²) — G1 Ch.7 p.62 (Indiana)
- Pass[G1-5] Energy per blow for D = 7.6 m, n = 0.4: (7.6/0.4)²·g (MJ) — G1 Ch.7 p.65 (Florida)
- Pass[G1-6] Required drop height for the 15 Mg tamper (m) — G1 Ch.7 p.65 (Florida)
- Pass[G1-7] Average applied energy 300 kJ/m³ × 7.6 m (MJ/m²) — G1 Ch.7 p.65 (Florida)
- Pass[G1-8] Energy of an 8-blow pass on the 9.1 m grid (kJ/m²) — G1 Table 13 p.67 (Florida)
- Pass[G1-9] Energy of a 9-blow pass on the 9.1 m grid (kJ/m²) — G1 Table 13 p.67 (Florida)
- Pass[G1-10] Energy of a 10-blow pass on the 9.1 m grid (kJ/m²) — G1 Table 13 p.67 (Florida)
- Pass[RD-V Becancour 10 ft] Theoretical impact velocity √(2gH), H = 10 ft (ft/s) — RD Table 5 p.49
- Pass[RD-R Becancour 10 ft] Measured/theoretical velocity ratio, v = 23.2 ft/s — RD Table 5 p.49
- Pass[RD-V Becancour 20 ft] Theoretical impact velocity √(2gH), H = 20 ft (ft/s) — RD Table 5 p.49
- Pass[RD-R Becancour 20 ft] Measured/theoretical velocity ratio, v = 31.5 ft/s — RD Table 5 p.49
- Pass[RD-V Becancour 58 ft] Theoretical impact velocity √(2gH), H = 58 ft (ft/s) — RD Table 5 p.49
- Pass[RD-R Becancour 58 ft] Measured/theoretical velocity ratio, v = 55 ft/s — RD Table 5 p.49
- Pass[RD-V Tulsa 18 ft] Theoretical impact velocity √(2gH), H = 18 ft (ft/s) — RD Table 5 p.49
- Pass[RD-R Tulsa 18 ft] Measured/theoretical velocity ratio, v = 30.5 ft/s — RD Table 5 p.49
- Pass[RD-V Tulsa 38 ft] Theoretical impact velocity √(2gH), H = 38 ft (ft/s) — RD Table 5 p.49
- Pass[RD-R Tulsa 38 ft] Measured/theoretical velocity ratio, v = 43 ft/s — RD Table 5 p.49
- Pass[RD-V Tulsa 73 ft] Theoretical impact velocity √(2gH), H = 73 ft (ft/s) — RD Table 5 p.49
- Pass[RD-R Tulsa 73 ft] Measured/theoretical velocity ratio, v = 60 ft/s — RD Table 5 p.49
- Pass[RD-V Great Lakes 18 ft] Theoretical impact velocity √(2gH), H = 18 ft (ft/s) — RD Table 5 p.49
- Pass[RD-R Great Lakes 18 ft] Measured/theoretical velocity ratio, v = 31.1 ft/s — RD Table 5 p.49
- Pass[RD-V Great Lakes 33 ft] Theoretical impact velocity √(2gH), H = 33 ft (ft/s) — RD Table 5 p.49
- Pass[RD-R Great Lakes 33 ft] Measured/theoretical velocity ratio, v = 42.5 ft/s — RD Table 5 p.49
- Pass[RD-R StMarys radar] Free-fall (radar) measured/theoretical ratio, 77.4 ft/s at 98 ft — RD Table 5 p.49
- Pass[RD-E1] Energy delivered at 90 % of theoretical speed, fraction of W·H ("approximately 80 percent") — RD p.50
- Pass[RD-E2] Energy delivered at 97 % of theoretical speed, free fall ("94 percent") — RD p.50
- PassLEDGER: at least 20 computed-value cases from four independent published sources
- Pass[lookup T7-granular-high] engine table equals G1 Table 7
- Pass[lookup T7-granular-low] engine table equals G1 Table 7
- Pass[lookup T7-silt-high] engine table equals G1 Table 7
- Pass[lookup T7-silt-low] engine table equals G1 Table 7
- Pass[lookup T7-clay-high] engine table equals G1 Table 7 ("Not recommended")
- Pass[lookup T7-clay-low] engine table equals G1 Table 7
- Pass[lookup T8-pervious] engine table equals G1 Table 8
- Pass[lookup T8-semipervious] engine table equals G1 Table 8
- Pass[lookup T8-landfill] engine table equals G1 Table 8
- Pass[lookup T8-proctor] engine table equals G1 Table 8 note
- Pass[lookup T2-pervious] engine table equals G1 Table 2
- Pass[lookup T2-sandy-silt] engine table equals G1 Table 2
- Pass[lookup T2-silt] engine table equals G1 Table 2
- Pass[lookup T2-clay-fill] engine table equals G1 Table 2
- Pass[lookup T2-landfill] engine table equals G1 Table 2
- Pass[lookup T3.13-commercial] engine table equals HAN Table 3.13
- Pass[lookup T3.13-residential] engine table equals HAN Table 3.13
- Pass[lookup T3.13-sensitive] engine table equals HAN Table 3.13
- PassPPV helper reproduces S3 Eq. 7 and its inverse (safe distance) closes exactly
- PassHan Eq. 3.17 typical drop height equals the energy-per-blow route for the S3 energy (≈ 30.2 m)
- PassSUPPLEMENTARY — Florida Table 13 energies close to ≤ 0.5 % if the printed "9.1 m" grid is the 30 ft (9.144 m) it was likely converted from
- PassDEVIATION D-1 — Indiana landfill phase energy: published 3.12 MJ/m² per phase vs 3.03 recomputed (−3.0 %)
- PassDEVIATION D-2 — Han §3.5.5 "13 % × 8.2 m = 1.10 m": the source arithmetic does not close (0.13 × 8.2 = 1.066 m)
- PassDEVIATION D-3 — Florida Table 13 induced settlement rows sum to 568 mm; the printed total is 694 mm
- PassDEVIATION D-4 — Han Table 3.11 (p.96) has no "sandy silts" row (it repeats "Sands and gravels" 40–50); GEC-1 Table 2 (primary) has sandy silts at SPT 34–45
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
effective-stress-site-response-web-validationValidation for the 1-D COUPLED EFFECTIVE-STRESS (liquefaction-capable) site-response column (`effective-stress-site-response.ts`) — the DEEPSOIL "effective stress" / OpenSees 1-D deliverable.12 passing
Analyses validated: effective-stress
- Pass[1-4] TOTAL-STRESS CONTROL: with generation off there is no pore pressure, no degradation, no period change
- Pass[5-7] EFFECTIVE STRESS: pore pressure builds, layers liquefy, and it is time-stamped
- Pass[8-9] SIGNATURE 1 — post-liquefaction DE-AMPLIFICATION of the surface motion
- Pass[10-11] SIGNATURE 2 — period lengthening of the softened profile
- Pass[12-13] DRY sand above the water table cannot liquefy
- Pass[14-15] effective overburden is buoyant below the water table and increases with depth
- Pass[16] a LOOSER sand (lower V_s) generates more pore pressure than a denser one
- Pass[17] a STRONGER motion generates more pore pressure
- Pass[18] Terzaghi dissipation (C_v > 0) leaves LESS residual pore pressure than the undrained limit
- Pass[19-21] outputs are physical and internally consistent
- Pass[22-23] the solve converges and returns no NaN/Infinity
- Pass[24] the elastic period is 4H/V_s and δ_G tracks r_u through √(1 − r_u)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-liquefaction-2d-web-validationrecords a differenceEXTERNAL-VALUE VALIDATION — phenomenological `fe-liquefaction-2d` path.2 passing
Analyses validated: fe-liquefaction-2d
- PassVELACS Model 1: all 20 fixed pore-pressure anchors remain traceable to the published record
- PassVELACS Model 1: phenomenological pore-pressure comparison is source-traced and honest
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-site-response-2d-web-validationWEB-BENCHMARK validation for the 2-D FE site-response (SH-wave basin) engine.8 passing
Analyses validated: fe-site-response-2d
- Pass2D-SR web C1–C4: T0 = 4H/Vs (exact)
- Pass2D-SR web: flat profile gives 2D/1D = 1.00 (validates vs 1-D baseline)
- Pass2D-SR web C5–C8: time-domain peak < Kramer spectral peak 1/(α+π/2·ξ) [upper bound]
- Pass2D-SR web C12–C19: basin 2D/1D focusing lands in the published band [1.15, 4]
- Pass2D-SR web: higher impedance contrast ⇒ higher 1-D amplification
- Pass2D-SR web: more damping ⇒ lower amplification
- Pass2D-SR web C10/C11: surface amplification stays physically bounded (< 12)
- Pass2D-SR published: Kramer Example 7.1 — f0 = 26.25 Hz for H = 10 ft, Vs = 1050 ft/s
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
lateral-spread-christchurch-web-validationrecords a differenceWEB-VALIDATION for `lateral-spread` against a PUBLISHED CASE HISTORY and an INDEPENDENT REFERENCE IMPLEMENTATION of the same model.12 passing
Analyses validated: lateral-spread
- PassChristchurch location A: cumulative prediction ≈ 3.2 m (Robinson et al. 2013 §5)
- PassChristchurch location A: the two events decompose as the paper describes
- PassChristchurch location A: over-predicts the 0.9 m field survey by more than 2× (paper abstract)
- PassChristchurch location A: W → 20% reproduces Figure 5(a) ≈ 4.2 m
- PassChristchurch location A: T₁₅ 1.5 / 3.5 m reproduce both ends of the Figure 5(a) bar
- PassChristchurch location A: coupled F₁₅ 35% / D₅₀ 0.13 mm LOWERS the prediction (fines dominate)
- PassChristchurch location A: R = R is closer to the observation than R = R_eq (paper §5)
- PassOpenQuake cross-check: free-face branch agrees to 1e-9 over a spread of cases
- PassOpenQuake cross-check: sloping-ground branch agrees to 1e-9
- PassOpenQuake cross-check: the free-face intercept is exactly the slope intercept − 0.500
- PassOpenQuake cross-check: the dependent variable is 10^Σ with NO offset (audit E-90)
- PassOpenQuake cross-check: R* = R + 10^(0.89·Mw − 5.64) and σ_logD = 0.197
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
lateral-spread-web-validationWeb-benchmark validation for `lateral-spread` — the Youd, Hansen & Bartlett (2002) revised multilinear regression for liquefaction-induced lateral spread displacement.7 passing
Analyses validated: lateral-spread
- Passgentle-ground displacement matches YHB (2002) Eq. 1 (α = 0, W = 1)
- Passfree-face displacement matches YHB (2002) Eq. 1 (α = 1, S = 1)
- PassR* follows Eq. 2 and boff is exactly the two-intercept difference
- Passthe confidence band uses the published σ_logDH = 0.1970
- PassE-90: the dependent variable is log DH, with no 0.01 m offset
- Passdamage bands break at the published 0.1 / 0.3 / 1.0 / 3.0 m edges
- Passout-of-range inputs warn per YHB Table 6 rather than failing silently
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
liquefaction-effective-stress-web-validationValidation for the COUPLED EFFECTIVE-STRESS liquefaction kernel (`liquefaction-effective-stress.ts`) — cyclic excess-pore-pressure generation and the stiffness/strength degradation it causes, i.e.13 passing
Analyses validated: liquefaction
- Pass[1-4] Carlton (2014): F = 3810·V_s^−1.55 exactly (DEEPSOIL Eq 4.11)
- Pass[5-8] Carlton (2014): s = (FC+1)^0.1252 exactly (DEEPSOIL Eq 4.12)
- Pass[9-11] Matasovic (1993): δ_G = √(1 − r_u) exactly (DEEPSOIL Eq 4.30)
- Pass[12-14] Matasovic (1993): δ_τ = 1 − r_u^v exactly (DEEPSOIL Eq 4.31)
- Pass[15] Dobry/Matasovic: strains at or below γ_tvp generate NO pore pressure (Eq 4.10)
- Pass[16] Dobry/Matasovic: r_u SATURATES at the limiting ratio p as N_c → ∞
- Pass[17-18] Dobry/Matasovic: r_u increases monotonically with N_c and with strain amplitude
- Pass[19-21] the analytic inverse round-trips the forward generation law EXACTLY
- Pass[22] required trend: a LOOSER sand (lower V_s) liquefies in FEWER cycles
- Pass[23] required trend: fines content raises the strain exponent s
- Pass[24-26] Terzaghi 1-D dissipation drains, stays bounded, and is stable at any C_v·dt/dz² (Eq 4.33)
- Pass[27-28] reversal bookkeeping: N_eq += ½ per reversal and r_u is monotone under undrained loading
- PasscyclicLiquefaction reports a consistent history (r_u monotone, flags agree)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
liquefaction-monitoring-web-validationWeb-benchmark validation for TWELVE liquefaction-triggering, in-situ-correlation, seismic-code and monitoring runner engines.12 passing
Analyses validated: cpt-liquefaction, design-code-spectrum, dmt, driven-pile-dynamics, embankment-stability, expansive-heave, liquefaction, multilayer-consolidation, pile-group-settlement, probabilistic-slope, spt-correlations, stabilization-mix, vs-liquefaction
- Passexpansive-heave reproduces the IS 9214 swell magnitude
- Passprobabilistic-slope computes β = (μ_FoS − 1)/σ_FoS and P_f = Φ(−β)
- Passmultilayer-consolidation sums the layered Terzaghi settlements
- Passdesign-code-spectrum reproduces ASCE 7-16 and switches code correctly
- Passpile-group-settlement uses the Randolph-Wroth influence radius
- Passstabilization-mix applies the IRC SP:89 CTB and CTSB UCS bands
- Passvs-liquefaction reproduces the full Andrus & Stokoe (2000) CRR chain
- Passcpt-liquefaction reproduces the Boulanger & Idriss (2014) CRR chain
- Passdmt reproduces the Marchetti (1980) index chain
- Passdriven-pile-dynamics reproduces the Hiley formula
- Passembankment-stability uses the undrained N_c·c_u bearing limit
- Passspt-correlations maps N to unit weight and equivalent q_c by soil type
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
liquefaction-settlement-web-validationWeb-benchmark validation for `liquefaction-settlement` — post-liquefaction reconsolidation settlement by the Ishihara-Yoshimine route.9 passing
Analyses validated: liquefaction-settlement
- Passεv matches I&B (2008) Eq 96 across (N1)₆₀cs at FoS = 0.9
- Passthe γmax branches of Eq 90-92 are selected as published
- PassEq 95 (Dr form) and Eq 96 (N form) agree to the published rounding
- PassE-91: Dr is floored at 0.4 for Eq 89, as I&B require
- PassEq 86 γlim, and the 8 % ceiling that makes the LDI 50 % cap moot
- Passsettlement is εv × thickness and sums down the profile
- PassE-99/D9: at (N1)60 = 20 the liquefied-zone strain sits in the 0.9-1.5 % band Fig 6 is drawn from
- PassE-99/D9: the report's envelope — 2-3 % for loose-to-medium sand, higher for very loose
- PassE-99: the T&S path still behaves monotonically and stays finite
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
liquefaction-triggering-variants-web-validationG9 — liquefaction-triggering VARIANTS: Robertson & Wride (1998) / Youd et al.32 passing
Analyses validated: cpt-liquefaction, cpt-sbt-ic, liquefaction
- PassΦ and Φ⁻¹: MethodsX Eq 43 Φ(1.77) = 0.96 and Eq 51c Φ(1.30) = 0.90; inverse round-trips
- Pass[C18] Eq 29-30: rd(5.5 m, Mw 6.8, amax 0.28, Vs12 220) = 0.97, σεrd = 0.084
- Pass[C18] Eq 32: mean CSR at the critical depth = 0.23 (σv 105.2, σ'v 80.7)
- Pass[C18] Eq 39: CRR(N1,60 11.4, FC 14, Mw 6.8, σ'v 80.7, PL 50 %) = 0.15
- Pass[C18] Eq 43: PL = Φ(1.77) = 0.96 at CSR 0.23
- Pass[C18] Eq 42: (N1)60cs = 11.4 + 14·(0.00167·11.4 + 0.089) = 12.9
- Pass[C18] Eqs 45, 47: Kσ(80.7 kPa) = 1.08, KMw(6.8) = 1.26
- Pass[C18] Eqs 49, 53, 54: CSR_ref = 0.17 and FS = CRR/CSR = 0.65 both ways
- Pass[C18] Eqs 51a-51c: σtot from σinput 7.01 = 4.03; PL with input uncertainty = Φ(1.30) = 0.90
- Pass[C18] Table 2 corrections reproduce Table 3: CN (σ'v) and CR (rod = depth + 1.2 m)
- Pass[C18] engine run of the Table 3 profile (procedure cetin_2018): N1,60 and CSR at every saturated depth
- Pass[C18] engine at the critical-layer means reproduces FS 0.65 and PL 0.96
- Pass[CGM10] Cetin 2004 MSF = (Mw/7.5)^−2.217: 1.99 at M 5.5, 0.76 at M 8.5
- Pass[CGM10] Cetin 2004 Kσ = (σ'v/Pa)^−0.278, limited to 1.5
- Pass[CGM10] Cetin 2004 CFINES, FC < 5 % → 0, and (N1)60 = 0 does not divide by zero
- Pass[CGM10] Cetin 2004 engine: FoS scales with Mw exactly by the published MSF
- Pass[MOSS] rd Eq 4.13 reproduces Table 4.1 rd (mid-depth of the critical layer) to its 2 dp
- Pass[CGM10] Moss 2006 embedded MSF = (Mw/7.5)^−0.118 and Kσ = (σ'v/Pa)^−0.00028
- Pass[MOSS] PL and CRR are consistent inverses; deterministic default PL = 15 % (§5.3)
- Pass[MOSS] c (Eq 4.2) against the c column of Table 4.1 — chart-read values, median |Δc| ≤ 0.06
- Pass[BI14] R&W Ic (n = 0.5 branch) reproduces the printed Ic of 13 Table 3.1 cases to ±0.015
- Pass[MOSS Fig 5.8 / Youd 2001 Eq 19] Kc: 1.0 at Ic 1.64, 2.14 at 2.36, 3.31 at 2.60
- PassYoud 2001 Eq 11: the two CRR7.5 branches meet at (qc1N)cs = 50; MSF(7.5) = 1.0 within 0.5 %
- PassRobertson 2009 Ic iteration is the already-validated cpt-sbt-ic implementation
- Passcpt-liquefaction: default procedure is unchanged (B&I 2014) and ignores sleeve friction
- Passcpt-liquefaction: R&W / Robertson 2009 / Moss require sleeve friction
- Passcpt-liquefaction R&W: clay-like Ic > 2.6 is non-susceptible, not a FoS
- Passcpt-liquefaction R&W: (qc1N)cs ≥ 160 → too dense to liquefy (Youd 2001 validity limit)
- Passcpt-liquefaction R&W hand-chain: FoS = CRR7.5(Kc·qc1N)·MSF·Kσ / CSR with NCEER rd
- Passcpt-liquefaction Robertson 2009: Kc = 1 in the 1.64 < Ic < 2.36, F < 0.5 % zone (R&C 2012)
- Passliquefaction (SPT): default procedure unchanged; Cetin procedures report PL; edge cases
- Passliquefaction (SPT): probability input validated; deterministic PL changes CRR monotonically
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
liquefaction-web-validationFormula-fidelity validation against Boulanger & Idriss (2014) "CPT and SPT Based Liquefaction Triggering Procedures", Report No.11 passing
Analyses validated: liquefaction
- Pass[1] EXISTING GOLDEN CASE (B&I 2014 Ex 8.1-class, M7.5, 0.36g, loose silty sand): FoS in the hand-computed 0.25-0.40 band, status liquefiable
- Pass[2] CRR_M7.5,sv=1atm matches Eq. 2.25 exactly, re-derived from the engine's own reported N160cs
- Pass[3] Ksigma matches Eq. 2.16a-c exactly, re-derived from the engine's own reported N160cs and effective stress
- Pass[4] MSF matches Eq. 2.18-2.21 exactly, re-derived from the engine's own reported N160cs and the case magnitude
- Pass[5] the final CRR (case-specific) equals CRR_M7.5,sv=1atm . MSF . Ksigma exactly (Miller/Idriss chain of corrections)
- Pass[6] FoS = CRR/CSR exactly
- Pass[7] CN overburden correction never exceeds the published 1.7 cap (Eq. 2.15a), even at very low overburden stress
- Pass[8] looser sand (larger m-exponent per Eq. 2.15c) gives a larger CN at the same effective stress than denser sand
- Pass[9] saturated unit weight raises total stress below the water table by exactly the submerged increment
- Pass[10] a higher PGA increases CSR and hence lowers the factor of safety, all else equal
- Pass[11] invalid inputs (zero PGA, zero SPT-N, magnitude out of range) are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
liquefaction-worked-examples-web-validationliquefaction — FULL WORKED EXAMPLES (the ≥20-value gate), end-to-end through computeLiquefaction.70 passing
Analyses validated: liquefaction
- Pass[MNO12] App. A z = 1.8 m: (N1)60cs = 8.5
- Pass[MNO12] App. A z = 1.8 m: CSR = 0.181
- Pass[MNO12] App. A z = 1.8 m: Kσ = 1.09
- Pass[MNO12] App. A z = 1.8 m: CRR_M7.5,σ=1 = 0.108
- Pass[MNO12] App. A z = 2.6 m: (N1)60cs = 7.05
- Pass[MNO12] App. A z = 2.6 m: CSR = 0.211
- Pass[MNO12] App. A z = 2.6 m: Kσ = 1.07
- Pass[MNO12] App. A z = 2.6 m: CRR_M7.5,σ=1 = 0.098
- Pass[MNO12] App. A z = 3.4 m: (N1)60cs = 9.37
- Pass[MNO12] App. A z = 3.4 m: CSR = 0.23
- Pass[MNO12] App. A z = 3.4 m: Kσ = 1.06
- Pass[MNO12] App. A z = 3.4 m: CRR_M7.5,σ=1 = 0.114
- Pass[MNO12] App. A z = 4.1 m: (N1)60cs = 11.39
- Pass[MNO12] App. A z = 4.1 m: CSR = 0.243
- Pass[MNO12] App. A z = 4.1 m: Kσ = 1.05
- Pass[MNO12] App. A z = 4.1 m: CRR_M7.5,σ=1 = 0.128
- Pass[MNO12] App. A z = 4.9 m: (N1)60cs = 13.29
- Pass[MNO12] App. A z = 4.9 m: CSR = 0.252
- Pass[MNO12] App. A z = 4.9 m: Kσ = 1.05
- Pass[MNO12] App. A z = 4.9 m: CRR_M7.5,σ=1 = 0.142
- Pass[MNO12] App. A z = 5.6 m: (N1)60cs = 28.14
- Pass[MNO12] App. A z = 5.6 m: CSR = 0.257
- Pass[MNO12] App. A z = 5.6 m: Kσ = 1.06
- Pass[MNO12] App. A z = 5.6 m: CRR_M7.5,σ=1 = 0.389
- Pass[MNO12] App. A z = 6.4 m: (N1)60cs = 23.4
- Pass[MNO12] App. A z = 6.4 m: CSR = 0.261
- Pass[MNO12] App. A z = 6.4 m: Kσ = 1.03
- Pass[MNO12] App. A z = 6.4 m: CRR_M7.5,σ=1 = 0.257
- Pass[MNO12] App. A z = 7.2 m: (N1)60cs = 32.28
- Pass[MNO12] App. A z = 7.2 m: CSR = 0.263
- Pass[MNO12] App. A z = 7.2 m: Kσ = 1.03
- Pass[MNO12] App. A z = 7.2 m: CRR_M7.5,σ=1 = 0.674
- Pass[MNO12] App. A z = 7.9 m: (N1)60cs = 24.18
- Pass[MNO12] App. A z = 7.9 m: CSR = 0.264
- Pass[MNO12] App. A z = 7.9 m: Kσ = 1.01
- Pass[MNO12] App. A z = 7.9 m: CRR_M7.5,σ=1 = 0.272
- Pass[MNO12] App. A z = 9.4 m: (N1)60cs = 25.13
- Pass[MNO12] App. A z = 9.4 m: CSR = 0.264
- Pass[MNO12] App. A z = 9.4 m: Kσ = 0.98
- Pass[MNO12] App. A z = 9.4 m: CRR_M7.5,σ=1 = 0.293
- Pass[MNO12] App. A z = 10.2 m: (N1)60cs = 15.57
- Pass[MNO12] App. A z = 10.2 m: CSR = 0.262
- Pass[MNO12] App. A z = 10.2 m: Kσ = 0.98
- Pass[MNO12] App. A z = 10.2 m: CRR_M7.5,σ=1 = 0.161
- Pass[MNO12] App. A z = 11 m: (N1)60cs = 13.52
- Pass[MNO12] App. A z = 11 m: CSR = 0.261
- Pass[MNO12] App. A z = 11 m: Kσ = 0.98
- Pass[MNO12] App. A z = 11 m: CRR_M7.5,σ=1 = 0.144
- Pass[MNO12] App. A: the two CH rows (PI 30) and the unsaturated 1.1 m row are not analysed
- Pass[CGM10] Table 3.1 1964 Niigata, Showa Br. 2: (N1)60cs = 8.2
- Pass[CGM10] Table 3.1 1964 Niigata, Showa Br. 2: CSR = 0.21
- Pass[CGM10] Table 3.1 1968 Tokachi-Oki, Aomori Station: (N1)60cs = 16.5
- Pass[CGM10] Table 3.1 1968 Tokachi-Oki, Aomori Station: CSR = 0.335
- Pass[CGM10] Table 3.1 1948 Fukui, Shonenji Temple: (N1)60cs = 11.8
- Pass[CGM10] Table 3.1 1948 Fukui, Shonenji Temple: CSR = 0.39
- Pass[CGM10] Table 3.1 1948 Fukui, Takaya 45: (N1)60cs = 21.1
- Pass[CGM10] Table 3.1 1948 Fukui, Takaya 45: CSR = 0.283
- Pass[CGM10] Table 3.1 1964 Niigata, Old Town 2: (N1)60cs = 23.5
- Pass[CGM10] Table 3.1 1964 Niigata, Old Town 2: CSR = 0.184
- Pass[CGM14] Table 6.1 1999 Chi-Chi, Wufeng Site A1: MSF = 0.97
- Pass[CGM14] Table 6.1 1999 Kocaeli, Degirmendere DN-1: MSF = 1
- Pass[CGM14] Table 6.1 1999 Kocaeli, Building C3: MSF = 1
- Pass[CGM14] Table 6.1 1999 Chi-Chi, Yuanlin BH-31: MSF = 0.99
- Pass[YOUD] Table 3 / IS 1893 Annex F Step 5: MSF(Mw 5.5) = 2.2
- Pass[YOUD] Table 3 / IS 1893 Annex F Step 5: MSF(Mw 6) = 1.76
- Pass[YOUD] Table 3 / IS 1893 Annex F Step 5: MSF(Mw 6.5) = 1.44
- Pass[YOUD] Table 3 / IS 1893 Annex F Step 5: MSF(Mw 7) = 1.19
- Pass[YOUD] Table 3 / IS 1893 Annex F Step 5: MSF(Mw 7.5) = 1
- Pass[YOUD] Table 3 / IS 1893 Annex F Step 5: MSF(Mw 8) = 0.84
- Pass[YOUD] Table 3 / IS 1893 Annex F Step 5: MSF(Mw 8.5) = 0.72
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
machine-foundation-web-validationrecords a differenceDedicated validation for the block machine-foundation vertical mode (`machine-foundation.ts`): Barkan/IS 2974 stiffness kz = Cu·A, natural frequency fnz = (1/2π)√(kz/m), frequency ratio r = f/fnz, damped magnification M = 1/√((1−r²)² + (2D…5 passing
Analyses validated: machine-foundation
- PassVarghese (2005) Example 23.1: vertical frequency, frequency ratio and undamped amplitude
- PassBowles (1997) Example 20-1A: printed natural frequency WN and frequency ratios W/WN
- PassBowles (1997) Example 20-1A: printed YP/YS (magnification) and YP (mm) at 800, 900, 1000 rpm
- PassVora (2018) Example 1: printed program results for the gas-engine foundation
- Passhand check: elastic half-space stiffness kz = 4 G r0 / (1 − ν) for the Bowles base (equivalent circle)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
makdisi-seed-web-validationmakdisi-seed — dedicated validation against PUBLISHED worked answers (`makdisi-seed.ts`).8 passing
Analyses validated: makdisi-seed
- Pass[K] Example 7.6 dam (H = 150 ft, Vs = 1200 ft/s): T0 = 0.33 s (printed in Ex. 10.5) and f = 3.1 Hz (Problem 10.9)
- Pass[K] Example 10.5: ky/kmax = 0.24/0.442 = 0.54
- Pass[K] Example 10.5: chart value 0.04 → u = 0.19 ft = 2.3 in
- Pass[M] Appendix A example (h = 150 ft, vs = 600 fps): first period T1 = 0.65 s
- Pass[M] p. 29-30: kmax = 0.2, ky = 0.14 → ky/kmax = 0.7
- Pass[M] p. 29-30: U/(kmax·g·T0) = 0.013 s, T0 = 0.99 s → U = 0.08 ft = 2.4 cm
- PassHAND-CHECK: U = norm·kmax·g·T0 and ky ≥ kmax is reported as not mobilised
- Passinvalid inputs are refused (no fabricated displacement): zero H, Vs, kmax; negative ky or chart value
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
nonlinear-site-response-codespectrum-web-validationWEB-BENCHMARK validation for the CODE DESIGN-SPECTRUM OVERLAY added to the nonlinear-site-response engine (IS 1893:2016 + ASCE 7-16).20 passing
Analyses validated: nonlinear-site-response
- Passoverlay 1: IS site class — Vs=250 ⇒ Type II (medium)
- Passoverlay 2: IS site class — Vs=500 ⇒ Type I (rock/hard)
- Passoverlay 3: IS site class — Vs=150 ⇒ Type III (soft)
- Passoverlay 4: ASCE site class — Vs=250 ⇒ D (stiff soil); Vs=500 ⇒ C
- Passoverlay 5: IS plateau — T=0.2 s ⇒ Sa = (Z/2)·2.5 = 0.20 g
- Passoverlay 6: IS rising branch — T=0.05 s ⇒ (Z/2)·(1+15·0.05) = 0.14 g
- Passoverlay 7: IS Type-II falling branch — T=1.0 s ⇒ (Z/2)·(1.36/1.0) = 0.1088 g
- Passoverlay 8: IS design Sa scales linearly with Z
- Passoverlay 9: ASCE plateau — T=0.5 s (T0<T<Ts) ⇒ Sa = SDS = 1.0 g
- Passoverlay 10: ASCE falling branch — T=1.0 s ⇒ SD1/T = 0.68 g
- Passoverlay 11: ASCE — T=2.0 s ⇒ SD1/T = 0.34 g
- Passoverlay 12: code spectrum is aligned 1:1 with the site-specific spectrum
- Passoverlay 13: verdict matches the site-vs-code comparison at the structure period
- Passoverlay 14: no structure period ⇒ verdict prompts to enter one
- Passoverlay 15: default code is IS 1893 (India-first)
- Passoverlay 16: EC8 ground type — Vs=250⇒C, Vs=500⇒B, Vs=900⇒A
- Passoverlay 17: EC8 plateau — T=0.4 s ⇒ ag·S·2.5 = 0.25·1.15·2.5 = 0.71875 g
- Passoverlay 18: EC8 falling branch — T=1.0 s ⇒ ag·S·2.5·(TC/T) = 0.43125 g
- Passoverlay 19: EC8 rising branch — T=0.1 s ⇒ ag·S·(1+T/TB·1.5) = 0.503125 g
- Passoverlay 20: EC8 design Sa scales linearly with ag
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
nonlinear-site-response-web-validationWEB-BENCHMARK validation for the 1-D nonlinear time-domain site-response engine.14 passing
Analyses validated: nonlinear-site-response
- PassNLSR web C1–C6: T0 = 4H/Vs (exact)
- PassNLSR web C7–C10: weak-motion amplification decreases monotonically with damping
- PassNLSR web C11–C13: strong motion DE-amplifies vs weak (period lengthening + hysteretic damping)
- PassNLSR web C16–C18: max shear strain grows monotonically with input PGA
- PassNLSR web C17: soft site (Vs≤200) + PGA≥0.1 g ⇒ strains large enough that NL matters
- PassNLSR web C20–C21: softer profile ⇒ longer site period
- PassNLSR web C24–C25: NEHRP-style deamplification — amplification falls as input PGA rises
- PassNLSR web: surface history + response spectrum are finite and non-empty
- PassNLSR web: elastic transfer function peaks at f₀, 3f₀, 5f₀
- PassNLSR web: strain/stress depth profiles + hysteresis loop are physical
- PassNLSR web: input accel history aligns with time + surface, peaks at the input PGA
- PassNLSR web: G/Gmax degrades + damping rises with strain (per-layer stiffness)
- PassNLSR web: vel/disp histories + Arias intensity + D₅₋₉₅ are physical
- PassNLSR web: surface Fourier spectrum peaks near the site period f₀
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pm4sand-web-validationValidation for the PM4Sand engine (`pm4sand.ts`).37 passing
Analyses validated: pm4sand
- PassCGM-15-01 eq 14 — M = 2·sin(33°) = 1.089
- PassCGM-15-01 eqs 12-13 — surfaces coincide at critical state (ξ_R = 0)
- PassCGM-15-01 eqs 12-13 — dense-of-critical gives M^b > M > M^d
- PassCGM-15-01 eq 45 — Bolton A_do = 1.26 at ξ_R = −0.1 (nb=0.5, nd=0.1)
- PassCGM-15-01 eq 45 — Bolton A_do = 1.45 at ξ_R = −0.7
- PassCGM-15-01 eq 97 — G_o = 167·√((N1)₆₀+2.5): 678 & 892 at N=14 & 26
- PassCGM-15-01 eq 96 — Vs1 = 85·((N1)₆₀+2.5)^0.25: 171 & 196 at N=14 & 26
- PassCGM-15-01 eq 92 — D_R = √((N1)₆₀/46): 0.552 & 0.752 at N=14 & 26
- PassIdriss-Boulanger 2008 — CRR at N=6/14/26 ≈ 0.090/0.147/0.312 (targets)
- PassIdriss-Boulanger CRR is monotonically increasing with density
- PassBoulanger-Idriss 2004 — Kσ = 1 at 1 atm and < 1 above 1 atm
- PassIdriss-Boulanger 2008 — MSF = 1 at M=7.5 and > 1 for smaller M
- PassCGM-15-01 eq 10-11 — relative-state index negative for dense sand
- PassCGM-15-01 Table 4.2 — default h_o = max((0.25+Dr)/2, 0.30)
- PassCGM-15-01 Table 4.2 — default z_max = 0.7 at ξ_R0 = 0, capped at 20
- PassPezeshk/IB-2014 — CRR₇.₅ matches the worked table across 13 (N1)₆₀cs values
- PassPezeshk/IB-2014 — Kσ matches the worked table across 5 rows
- PassIdriss-Boulanger CRR caps at 2.0 for very dense sand ((N1)₆₀cs ≥ ~38)
- PassPezeshk/IB-2014 — r_d(z, M=7.7) matches the worked table across 8 depths
- PassPezeshk/IB-2014 — CSR = 0.65·(a_max/g)·(σv/σ′v)·r_d matches 8 rows
- PassPezeshk/IB-2014 — end-to-end FoS via the a_max path matches the table (0.469)
- PassIntegrator — undrained cyclic DSS reaches full liquefaction (r_u → ~1)
- PassIntegrator — cycles-to-liquefaction decreases as CSR increases (CRR-N trend)
- PassIntegrator — mid-density element CRR matches I&B target 0.147 within 12%
- PassIntegrator — h_po (contraction knob) monotonically raises element CRR
- PassIntegrator — stress path shows p reduction toward liquefaction
- PasscomputePm4Sand — end-to-end wrapper returns a factor of safety and CRRs
- PasscyclesToLiquefactionFromFoS — N = 15 at FoS = 1, monotone in FoS
- PassDense sand no longer contradicts FoS — N45/CSR0.5 safe, N30/CSR0.1 safe
- PassLoose sand triggers fast — N6/CSR0.35 FoS<1 and cycles<15
- Passcycles-to-liquefaction is monotone: denser/weaker shaking ⇒ more cycles
- Passaudit: CSR = 0 is REFUSED, not reported as FoS ≈ 110 929
- Passaudit: negative n160 / sigmaVc are REFUSED, not silently turned into NaN with errors: []
- Passaudit: maxCycles is bounded — no heap exhaustion from an extreme value
- Passaudit: the kernel bounds stored series in place even for a run that never triggers
- Passaudit: the real, valid case is BYTE-IDENTICAL to before the fix
- Passaudit: n160 = 0 (very loose sand) stays LEGAL
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pore-pressure-generation-web-validationFormula-fidelity validation for the tool surfaced at /tools/liquefaction- response (module: pore-pressure-generation.ts, NOT named after the slug -- one of the documented module-resolution traps).9 passing
Analyses validated: liquefaction-response
- Pass[1-5] equivalent uniform cycles N_eq matches the published Seed & Idriss (1982) table anchors exactly: M5.25=2.5, M6.0=5, M6.75=10, M7.5=15, M8.5=26
- Pass[6] ru=1 exactly at cycle ratio N/NL=1 (the defining anchor of initial liquefaction, per Seed-Martin-Lysmer 1976)
- Pass[7-8] ru matches the exact Seed-Martin-Lysmer closed-form at two intermediate ratios: ratio=0.5 -> ru=0.417265, ratio=0.25 -> ru=0.242312
- Pass[9] ru=0 exactly at N=0 (no cycles, no pore pressure generated)
- Pass[10-13] CROSS-ENGINE CHECK: feeding this engine the actual B&I 2014 CRR/CSR from the already-validated liquefaction.ts engine (see liquefaction-web-validation.test.ts) reproduces the exact expected FS, Neq, and NL
- Pass[14] a non-liquefying case (FS>1) is correctly flagged, and the final ru stays below 1
- Pass[15] the stiffness ratio G/Gmax = sqrt(1-ru) exactly, per Hardin & Drnevich (1972) stress dependence
- Pass[16] the effective stress path sigma_v_eff = sigma_v0.(1-ru) exactly, when sigma_v0 is supplied
- Pass[17] invalid inputs (zero CSR/CRR, magnitude outside 4-9.5) are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
response-spectrum-web-validationValidation for the seismic response spectrum (`response-spectrum.ts`).6 passing
Analyses validated: not attributed by the manifest
- PassPGA of the sinusoid = amplitude A
- Passrigid limit: Sa(T→0) → PGA
- Passresonance: Sa ≈ PGA/(2ζ) for a SDOF tuned to the input frequency
- Passpseudo-spectral relations Sv=ω·Sd, Sa=ω²·Sd hold
- Passzero ground motion → zero response
- PassArias intensity closed form Ia = (π/2g)∫a²dt
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rvt-site-response-web-validationValidation for the RVT site-response engine (`rvt-site-response.ts`).34 passing
Analyses validated: rvt-site-response, site-response-multilayer
- Passspectral moment m0 = 2A²(f2−f1)
- Passspectral moment m2 = 2A²(2π)²(f2³−f1³)/3
- Passspectral moment m4 = 2A²(2π)⁴(f2⁵−f1⁵)/5
- Passmoments scale with A²
- PassRVT bandwidth ξ = √(m₂²/(m₀m₄)) of [0,fmax] white noise = √5/3 (exact)
- Passzero-crossing rate = 2·fmax/√3 for [0,fmax] white
- Passextrema rate = 2·fmax·√(3/5) for [0,fmax] white
- Passn_extrema ≥ n_zero
- Passpeak factor > 1
- Passpeak factor increases with duration
- PassCLH peak factor ≈ Davenport asymptote (broadband)
- Passpeak factor is O(√(2 ln Ne))
- Passrms duration → D_gm at long period
- Passrms duration → D_gm + Tn/(2πβ) at short period
- Passrms duration ≥ D_gm
- Passrms duration decreases with damping
- PassPSA(T→0) approaches PGA
- Passresponse spectrum positive & finite
- Passlower oscillator damping → higher Sa
- PassBrune corner frequency drops with magnitude
- Passsingle-layer site period ≈ 4H/Vs
- Passsoft-soil amplification > 1
- Passsurface PGA ≥ rock PGA
- Passsurface Sa peak ≥ surface PGA
- Passsofter soil → longer period + more amplification
- Passfundamental period within physical band of 4H/Vs
- PassKramer Eq 7.19 — single layer over rigid rock: |F|(f0) = 1/(ξ·π/2)
- PassKramer — single layer over elastic rock: |F|(f0) = 1/α_z (undamped soil)
- PassKramer — fundamental period T0 = 4H/Vs across cases
- PassKramer — odd higher modes resonate: |F|(3f0) > |F|(2f0)
- PassToro 1995 Vs randomization — median ≈ base, ordered p16 ≤ median ≤ p84, deterministic
- Passaudit: bedrock damping far beyond 100% critical is REFUSED
- Passaudit: a negated layer (thickness, Vs, unit weight, damping) is REFUSED, not a plausible period
- Passaudit: the real, valid single-layer case is unaffected by the new per-field checks
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
seismic-site-class-crosscode-web-validationrecords a differenceseismic-site-class — deep review D11 (2026-10-02).15 passing
Analyses validated: seismic-site-class
- Pass[IDOT] N̄ (Method B) on five published 100-ft profiles — 9, 7, 21, 19, 23 blows/ft
- Pass[IDOT] s̄u (Method C, cohesive layers only) — 0.68, 2.17, 4.62, 3.51, 4.62 ksf
- Pass[IDOT] the published class for each measure (AASHTO 3.10.3.1-1 = ASCE 7-16 Table 20.3-1 limits)
- Pass[IDOT] → IS 1893 Table 4 on the published N̄: 9, 7 → Type III; 21, 19, 23 → Type II
- Pass[PEER] Dobry et al. 2000 example: 18 m @ 90 m/s over 12 m @ 260 m/s → Vs30 = 122 m/s (arithmetic 158)
- Pass[CE] travel-time Vs30 solved problems — 372.2, 308 and 424 m/s
- Pass[EQ03] IS 1893:2016 Example 1 — Zone V, I 1, R 5, Type II, T 0.28 s → Sa/g 2.5, Ah 0.09
- Pass[STAAD] IS 1893:2016 static seismic — Z 0.36, I 1.2, R 5, hard soil, Ta 0.39 s → Sa/g 2.5, Ah 0.108, VBmin 2.4 %
- Pass[IS] Table 7 minimum VB/W for buildings — 0.7, 1.1, 1.6, 2.4 % (Zones II-V)
- Pass[IS] Cl 6.4.2(a) vs (b): a rigid structure gets 2.5 by the equivalent static method, 1 + 15T by the response spectrum method
- Pass[IS] Cl 6.3.5.3 — the liquefaction N limit is 15 in Zones III-V and 10 in Zone II, and no site type is exempt
- Pass[EN] Table 3.2 / 3.3 recommended spectrum parameters on ground types C and D
- Pass[JRC] Worked example §3.2: clay with cu,d = 300 kPa (270 kPa seismic) is ground type B
- Pass[EN] Table 3.1 ground type E — 5-20 m of vs < 360 m/s directly over vs > 800 m/s
- PassD11 regressions — averaging tracks true depth, s̄u stays on the cohesive layers, s̄u alone never gives Type I
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
seismic-site-class-is1893-web-validationSeismic site classification and design coefficient — validated against **IS 1893 (Part 1):2016**, *Criteria for Earthquake Resistant Design of Structures*, Part 1 General Provisions and Buildings (6th revision).6 passing
Analyses validated: seismic-site-class
- PassIS 1893:2016 Table 3 — the four published zone factors Z
- PassQ-3 / E-8 — omitting the seismic zone is REFUSED, never a silent Ah = 0
- PassIS 1893:2016 Cl 6.4.2 Fig 2(b) — the design acceleration spectrum, all three site classes
- PassE-31 — the T > 4 s floor exists, and the old behaviour would have been unconservative
- PassIS 1893:2016 Cl 6.4.2 — Ah = (Z/2)·(I/R)·(Sa/g), end to end
- Passthe references cite the tables that were actually used, with the corrected numbers
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
site-response-design-chain-web-validationWeb-benchmark validation for the SEVEN remaining inline runner engines: 1-D site response (equivalent-linear, nonlinear and effective-stress), climate/EICM, the staged embedded wall, and the two probabilistic/full-chain foundation engines.7 passing
Analyses validated: bearing-capacity-reliability, climate-zone-eicm, effective-stress-liquefaction, foundation-analysis, nonlinear-site-response, site-response, site-response-multilayer, staged-excavation-wall
- Passsite-response-multilayer reports both the exact and quarter-wavelength periods
- Passnonlinear-site-response uses T = 4H/V_s and overlays the code spectrum
- Passeffective-stress-liquefaction keeps r_u bounded and its outputs mutually consistent
- Passclimate-zone-eicm returns distinct, physically ordered values for all six zones
- Passstaged-excavation-wall uses Rankine K_a/K_p and keeps the wall check consistent
- Passbearing-capacity-reliability takes the EC7 characteristic value as the 5th percentile
- Passfoundation-analysis takes the LESSER of shear and settlement capacity at every width
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
site-response-eql-web-validationValidation for the equivalent-linear site-response engine + G/Gmax–damping curve library (`site-response-eql.ts`, `gmax-damping-curves.ts`).11 passing
Analyses validated: site-response-eql
- PassVucetic-Dobry (1991): G/Gmax anchors at γ = 0.1% vs PI
- PassVucetic-Dobry (1991): damping anchors at γ = 0.1% vs PI
- PassVucetic-Dobry: small-strain plateau and large-strain degradation
- PassSeed-Idriss (1970) sand: mean G/Gmax and damping anchors
- PassDarendeli (2001): reference strain and D_min for PI=0, 1 atm
- PassDarendeli (2001): G/Gmax = 0.5 at γ = γr (definition of the reference strain)
- PassEQL reduces to the linear transfer function at very low input
- PassEQL lengthens the period and de-amplifies under strong motion (Kramer §7)
- PassEQL effective-strain ratio R_γ tracks magnitude (Seed-Idriss)
- PassEQL input validation
- PassEQL small-strain fundamental period = 4H/Vs (Kramer Eq 7.16 + Ex 7.1/7.2)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
site-response-fe-1d-web-validationWEB-VALIDATION for the 1-D site-response FE by Newmark-β time integration (`site-response-fe-1d.ts`).14 passing
Analyses validated: site-response
- PassA1. Newmark SDOF resonance r=1 → Rd = 1/(2ζ) = 10.000 (Chopra §3.2)
- PassA2. Newmark SDOF r=0.5 → Rd = 1.33038 (Chopra §3.2)
- PassA3. Newmark SDOF r=2.0 → Rd = 0.33260 (Chopra §3.2)
- PassA4. Newmark SDOF quasi-static r=0.1 → Rd → 1.0 (Chopra §3.2)
- PassA5. Newmark undamped free vibration preserves period + amplitude
- PassB1. fundamental frequency f1 = Vs/(4H) = 2.00 Hz (Kramer Eq. 7.13)
- PassB2. peak mode-1 amplification = 2/(πζ) = 12.7324 (Kramer Eq. 7.20)
- PassB3. 2nd resonance at f2 = 3·f1 = 6.0 Hz, amp = 2/(3πζ) = 4.2441 (Kramer)
- PassB4. low-frequency limit → amplification ≈ 1 (surface rides the base)
- PassB5. second uniform site Vs=180, H=30 → f1 = 1.50 Hz (Kramer Eq. 7.13)
- PassC1. Rayleigh a0,a1 match the closed form and give ζ at both controls
- PassD1. Newmark time-domain surface/base ratio at f1 = FD transfer fn ≈ 2/(πζ)
- PassE1. computeSiteResponseFE1D reports f1, peak amp and runs a base motion
- PassE2. edge cases: invalid inputs surface errors, not NaN
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
site-response-web-validationFormula-fidelity validation against Kramer, "Geotechnical Earthquake Engineering" Ch.7 -- the classical single-layer, vertically-propagating SH-wave transfer function on an elastic half-space.11 passing
Analyses validated: site-response
- Pass[1-2] fundamental period T0=4H/Vs=0.4s, fundamental frequency f0=1/T0=2.5Hz
- Pass[3] resonant frequencies fn=(2n-1).Vs/(4H) for n=1,2,3: 2.5, 7.5, 12.5 Hz
- Pass[4] impedance ratio alpha = (rho_soil.Vs_soil)/(rho_rock.Vs_rock) matches exactly: 0.215311
- Pass[5] peak damped amplification A_max = 1/(alpha + (pi/2).xi) matches exactly: 3.403087
- Pass[6] surface PGA equals rock PGA times the peak amplification exactly
- Pass[7] a softer soil column (lower impedance ratio) produces MORE amplification -- the classical soft-site resonance danger
- Pass[8] a deeper soil layer lowers the fundamental frequency (longer period), all else equal
- Pass[9] more damping reduces the peak amplification, all else equal
- Pass[10] the amplification spectrum starts at exactly 1.0 at zero frequency (no dynamic effect at DC)
- Pass[11] a bedrock softer than the soil column is refused (Vs_rock >= Vs_soil is required for the model to be physically meaningful)
- Pass[12] invalid inputs (zero thickness, zero Vs, damping outside [0,1)) are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
spectral-matching-web-validationValidation for the RSPMatch-style time-domain spectral matcher (`spectral-matching.ts`).6 passing
Analyses validated: not attributed by the manifest
- Passspectral matching dramatically reduces the misfit vs the seed
- Passmatch is within ~10% over the well-resolved period range T ≥ 0.5 s
- Passmatched motion has no baseline drift (final velocity ≈ 0)
- Passnon-stationarity preserved: PGA and Arias stay the same order as the seed
- Passdeterministic: same seed + target ⇒ identical matched motion
- Passconfig wrapper returns misfit in % and preserves the record length
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
topographic-amplification-web-validationWEB-BENCHMARK validation for the 2-D topographic-amplification (SH ridge/crest) engine.10 passing
Analyses validated: site-response-multilayer, topographic-amplification
- Passtopo web EC8: flat surface S_T = 1.00 across geometries (3 cases)
- Passtopo web Trifunac: S_T < 2 for every ridge shape (6 cases, incl. steep)
- Passtopo web EC8: 15°–30° slopes give S_T ≥ 1.2 (4 cases)
- Passtopo web EC8: >30° ridges give S_T ≥ 1.4 (3 cases)
- Passtopo web Ashford-Sitar: steep ridges (60°, 70°) amplify 1.4–2.0, never de-amplify
- Passtopo web EC8: gentle ridges (slope ~6°, ~10°) ⇒ S_T ≈ 1.0–1.25
- Passtopo web: S_T rises monotonically with slope angle (5°→10°→20°→30°→45°)
- Passtopo web EC8: crest is the surface-profile peak, base ≈ free-field
- Passtopo web Geli: resonant crest amplification is in the 1.3–2.0 band for a steep ridge
- Passtopo web: dimensionless frequency η at the peak is reported and physical (0.3–2)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
vs-liquefaction-web-validationValidation for the shear-wave-velocity liquefaction-triggering engine (`vs-liquefaction.ts`, Andrus & Stokoe 2000 simplified procedure as adopted by the NCEER workshop).9 passing
Analyses validated: vs-liquefaction
- PassYoud & Idriss (2001) Table 3 — revised Idriss MSF at Mw 5.5 … 8.5
- PassYoud & Idriss (2001) p. 825 — CRR_7.5 = 0.033 at V_s1 = 100 m/s (clean sand)
- PassYoud & Idriss (2001) p. 825 — V*_s1 = 215 m/s (FC ≤ 5 %) … 200 m/s (FC ≥ 35 %)
- PassTreasure Island crosshole, 4.57 m — V_s1, V*_s1, CSR, CRR and F_S of the worked example
- PassTreasure Island crosshole, 5.49 m — Table 3.2 row 2 (V_s1 150 m/s, r_d 0.96)
- PassTreasure Island crosshole, 6.40 m — Table 3.2 row 3 (V_s1 158 m/s, r_d 0.95, CSR 0.14)
- PassTreasure Island SASW, 5.34 m — Table 3.3 (V_s1 149 m/s, r_d 0.96) and the F_S = 0.75 minimum
- PassMarina District School, 3.02 m — Table 3.4 row 1 (V_s1 104 m/s, r_d 0.98, CSR 0.10) and F_S = 0.42
- PassMarina District School, 3.94 m — Table 3.4 row 2 (V_s1 156 m/s, r_d 0.97, CSR 0.11) and F_S = 0.90
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Constitutive models and element tests
48 finite-element rows (12 deviations) · 0 closed-form problems · 27 validation suites
Finite-element solver registry
Showing 48 of 48 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
normalised cavity pressure p/c at (a − a0)/a0 = 4 (also 0.4 / 1.2 / 2.8 within 0.15 %) plaxis-verif-cavity-pressure | 7.6812 | 7.6846 | −0.04 % | Ours 7.6812Published 7.6846−0.04 % | Pass | |
| ||||||
radius of the plastic zone at a = 5 m (outermost plastic integration point) plaxis-verif-cavity-rp | 28.003m | 28.28m | −0.99 % | Ours 28.003 mPublished 28.28 m−0.99 % | Pass | |
| ||||||
normalised cavity pressure p/c at (a − a0)/a0 = 4, updated mesh (worst step over the curve −0.22 %) plaxis-verif-cavity-large-pressure | 5.5628 | 5.5668 | −0.07 % | Ours 5.5628Published 5.5668−0.07 % | Pass | |
| ||||||
radius of the plastic zone at a = 5 m, current configuration (outermost plastic integration point) plaxis-verif-cavity-large-rp | 48.74m | 49.11m | −0.76 % | Ours 48.74 mPublished 49.11 m−0.76 % | Pass | |
| ||||||
ux / uy of the corner nodes plaxis-verif-biaxial-le · Self-check | identical to 1e-13 | identical | 0.00 % | Ours identical to 1e-13 mmPublished identical mm0.00 % | Pass | |
| ||||||
γxy plaxis-verif-biaxial-shear | 0.0025 | 0.0025 | 0.00 % | Ours 0.0025Published 0.00250.00 % | Pass | |
| ||||||
failure σ1 (load control) plaxis-verif-biaxial-mc | -6.4641kPa | -6.4641kPa | 0.00 % | Ours -6.4641 kPaPublished -6.4641 kPa0.00 % | Pass | |
| ||||||
HS drained triaxial compression: σ'1 at failure (σ'3 = −100 kPa) k5b-hs-triaxial-element-compression | -372.859kPa | -372.86kPa | +2.0e-4 % | Ours -372.859 kPaPublished -372.86 kPa+2.0e-4 % | Pass | |
| ||||||
HS drained triaxial extension: σ'1 at failure k5b-hs-triaxial-element-extension | -26.0579kPa | -26.06kPa | +8.1e-3 % | Ours -26.0579 kPaPublished -26.06 kPa+8.1e-3 % | Pass | |
| ||||||
HS triaxial through the FE solver: σ'1 at failure (stops at λ 0.779598 of −100 → −450; honest collapse) k5b-hs-triaxial-fe-compression | -372.859kPa | -372.86kPa | +3.0e-4 % | Ours -372.859 kPaPublished -372.86 kPa+3.0e-4 % | Pass | |
| ||||||
HS triaxial extension through the FE solver: σ'1 at failure (λ 0.739421) k5b-hs-triaxial-fe-extension | -26.058kPa | -26.06kPa | +7.7e-3 % | Ours -26.058 kPaPublished -26.06 kPa+7.7e-3 % | Pass | |
| ||||||
HS drained triaxial at σ'3 = −pref, normally consolidated (cap active — the STANDARD test): secant E50 at qf/2 (and, with the cap out of the way, max |ε1 − hyperbola of the internal Ei^ref|/ε1 up to 0.55 qf) k5b-hs-hyperbola-e50 | 19999.6kPa | 20000kPa | −2.0e-3 % | Ours 19999.6 kPaPublished 20000 kPa−2.0e-3 % | Pass | |
| ||||||
HS small: simple-shear secant G(γ) = G0/(1 + 0.385 γ/γ0.7) (worst relative error) k5b-hs-small-dss-reloading | 7.000e-15 | 0 | — | Ours 7.000e-15Published 0— | Pass | |
| ||||||
HS small (G0ref 3 Gur, γ0.7 1e-4) drained triaxial: σ'1 at failure k5b-hs-small-triaxial-failure | -372.859kPa | -372.86kPa | +2.0e-4 % | Ours -372.859 kPaPublished -372.86 kPa+2.0e-4 % | Pass | |
| ||||||
Soft Soil isotropic NC compression / unloading: recovered λ*, κ* (input 0.1055 / 0.01635) k5b-ss-isotropic-lambda-kappa | 0.105515 / 0.016335 | 0.1055 / 0.01635 | — | Ours 0.105515 / 0.016335Published 0.1055 / 0.01635— | Pass | |
| ||||||
Soft Soil oedometer: σ'h/σ'v on the NC line k5b-ss-oedometer-k0nc · Self-check | 0.609978 | 0.61 | −3.6e-3 % | Ours 0.609978Published 0.61−3.6e-3 % | Pass | |
| ||||||
Soft Soil Creep: isotropic creep strain at 1012 d under constant p' (backward Euler, 5 % growing steps) k5b-ssc-isotropic-creep | 0.027585 | 0.027681 | −0.35 % | Ours 0.027585Published 0.027681−0.35 % | Pass | |
| ||||||
Haney clay: p_p^eq after POP 432.4 initialisation k5b-ssc-haney-pp | 372.99kPa | 373kPa | −2.7e-3 % | Ours 372.99 kPaPublished 373 kPa−2.7e-3 % | Pass | |
| ||||||
Haney clay undrained triaxial peak q at 0.00094 / 0.15 / 1.10 %/min k5b-ssc-haney-rate-effect · Self-check | A: 269.7; B: 327.3; C: 353 | —kPa | — | Ours A: 269.7; B: 327.3; C: 353 kPaPublished — kPa— | Pass | |
| ||||||
MCC undrained triaxial on NC clay (p'0 200, λ 0.25, κ 0.05, M 0.9): p' at critical state k5b-mcc-undrained-nc | 114.859kPa | 114.87kPa | −9.1e-3 % | Ours 114.859 kPaPublished 114.87 kPa−9.1e-3 % | Pass | |
| ||||||
Hoek–Brown triaxial strength at σ3 = 0, −1, −5, −15 MPa (GSI 50, mi 10, σci 30 MPa): max relative miss k5b-hb-envelope | < 1e-6 (asserted) | 0 | — | Ours < 1e-6 (asserted)Published 0— | Pass | |
| ||||||
NGI-ADP plane-strain strengths s_u^A / s_u^P / s_u^DSS (input 50 / 25 / 35) k5b-ngi-adp-strengths · Self-check | 50.0000 / 25.0000 / 35.0000 | 50 / 25 / 35 | — | Ours 50.0000 / 25.0000 / 35.0000 kPaPublished 50 / 25 / 35 kPa— | Pass | |
| ||||||
consistent tangent vs central FD, worst relative error (4×4 through Plane<M>; 6×6 on fully 3-D states) k5b-tangent-check | 4x4 worst: 2.400e-7; 6x6 HS: 2.800e-8; HSs: 2.500e-8; SS: 2.800e-7; SSC: 2.800e-7; MCC: 9.800e-8; HB: 3.900e-9; NGI-ADP… | 0 | — | Ours 4x4 worst: 2.400e-7; 6x6 HS: 2.800e-8; H…Published 0— | Pass | |
| ||||||
random-state return-mapping sweep: failed returns per 4000 (HS, HSs, SS, SSC, MCC, HB, HB ψ, NGI-ADP) k5b-return-robustness | 0 | 0 | — | Ours 0Published 0— | Pass | |
| ||||||
top settlement of a confined column with E(y) = E_ref + E_inc (y_ref − y) k5a-einc-column | 0.0204028m | 0.0204028m | 0.00 % | Ours 0.0204028 mPublished 0.0204028 m0.00 % | Pass | |
| ||||||
limit load factor ΣMstage of the load-controlled bi-axial MC test under arc-length control k5a-arc-length-biaxial-limit | 0.607122 | 0.607122 | 0.00 % | Ours 0.607122Published 0.6071220.00 % | Pass | |
| ||||||
consistent tangent of the principal-space MC + tension cut-off return, non-associated (φ/ψ/σt = 30/0/0, 32/2/0, 25/0/1, 35/10/0) vs central FD and AD k5a-mc-principal-tangent · Self-check | 5.430e-7|ΔD|/E | 1.000e-6|ΔD|/E | — | Ours 5.430e-7 |ΔD|/EPublished 1.000e-6 |ΔD|/E— | Pass | |
| ||||||
Hoek–Brown Safety reduction f = σ3 − σ1 − f̄(σ3)/η(σ3): the reduced envelope is the local tangent Mohr–Coulomb reduced by ΣMsf k5d1-hb-strength-factorisation · Self-check | — | 1.000e-6 | — | Ours —Published 1.000e-6— | Pass | |
| ||||||
HS-1 εv medium (drained TC, MMM Fig 13.3): max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-1 · Self-check | 2.452 | 1 | — | Ours 2.452Published 1— | Deviation | |
| ||||||
HS-1 εv dense: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-2 · Self-check | 1.347 | 1 | — | Ours 1.347Published 1— | Deviation | |
| ||||||
HS-4 εv dense (Hostun): max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-3 · Self-check | 1.001 | 1 | — | Ours 1.001Published 1— | Deviation | |
| ||||||
HS-2 q medium (undrained): max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-4 · Self-check | 3.595 | 1 | — | Ours 3.595Published 1— | Deviation | |
| ||||||
HS-2 q dense: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-5 · Self-check | 3.704 | 1 | — | Ours 3.704Published 1— | Deviation | |
| ||||||
HS-2 P_excess medium: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-6 · Self-check | 1.334 | 1 | — | Ours 1.334Published 1— | Deviation | |
| ||||||
HS-2 P_excess dense: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-7 · Self-check | 7.456 | 1 | — | Ours 7.456Published 1— | Deviation | |
| ||||||
HSS-1 G dense σ3 100 kPa (Benz 2007 Fig 8.2/8.3): max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-8 · Self-check | 1.562 | 1 | — | Ours 1.562Published 1— | Deviation | |
| ||||||
HSS-1 G loose σ3 100 kPa: max normalised distance to the published markers (rule ≤ 1) v-hs-published-curve-9 · Self-check | 2.765 | 1 | — | Ours 2.765Published 1— | Deviation | |
| ||||||
wall displacement and tangential stress around a hole in transversely isotropic rock, vs the Amadei closed form geostudio-sigmaw-transversely-isotropic-amadei | — | — | +0.18 % | Ours —Published —+0.18 % | Pass | |
| ||||||
lambda(s) for suction s = 0.04 / 0.06 / 0.09 MPa geostudio-sigmaw-bbm-lambda-suction-alonso | 0.0601 | 0.06 | +0.17 % | Ours 0.0601Published 0.06+0.17 % | Pass | |
| ||||||
LC yield-curve preconsolidation pressure p0(s) for s = 0.06 / 0.09 MPa geostudio-sigmaw-bbm-lc-yield-alonso | 85.1kPa | 85kPa | +0.12 % | Ours 85.1 kPaPublished 85 kPa+0.12 % | Pass | |
| ||||||
volumetric strain epsilon_v on four load steps (isotropic compression) geostudio-sigmaw-ss1-mmm-isotropic-compression | — | — | +2.26 % | Ours —Published —+2.26 % | Pass | |
| ||||||
NorSand drained plane-strain biaxial compression (sigma_3 constant, eps_2 = 0) to eps_1 = 150 %, dense psi_0 = -0.1 (Fig. 3.18a base set): critical stress ratio eta m17-norsand-cs-plane-strain-lode0 | 0.99008 | 0.990034 | +5.0e-3 % | Ours 0.99008Published 0.990034+5.0e-3 % | Pass | |
| ||||||
NorSand undrained triaxial EXTENSION from a loose isotropic state (psi_0 = +0.03, 200 kPa) to eps_q = 50 %: critical stress ratio eta m17-norsand-cs-triaxial-extension | 0.88235 | 0.882353 | 0.00 % | Ours 0.88235Published 0.8823530.00 % | Pass | |
| ||||||
General-stress return vs the pre-M17 triaxial integrator on 6 book paths (Fig. 3.18a drained psi_0 = -0.2, -0.1, 0, +0.04; Fig. 6.19 undrained L601, C609): max |difference| of p', q, eps_v over all output points m17-norsand-general-vs-triaxial-reference · Self-check | 7.224e-9 | 0 | +7.2e-7 % | Ours 7.224e-9Published 0+7.2e-7 % | Pass | |
| ||||||
NorSand drained plane strain (Cornforth apparatus, sigma_3 = 276 kPa, eps_2 = 0, K0 start), Brasted sand, loose (test A10-14): peak major principal stress sigma_1 m17-norsand-brasted-plane-strain-peak-loose | 1100kPa | 1033kPa | +6.50 % | Ours 1100 kPaPublished 1033 kPa+6.50 % | Deviation | |
| ||||||
NorSand drained plane strain (Cornforth apparatus, sigma_3 = 276 kPa, eps_2 = 0, K0 start), Brasted sand, compact (test A10-12): peak major principal stress sigma_1 m17-norsand-brasted-plane-strain-peak-compact | 1303kPa | 1186kPa | +9.90 % | Ours 1303 kPaPublished 1186 kPa+9.90 % | Deviation | |
| ||||||
NorSand drained plane strain (Cornforth apparatus, sigma_3 = 276 kPa, eps_2 = 0, K0 start), Brasted sand, dense (test A10-17): peak major principal stress sigma_1 m17-norsand-brasted-plane-strain-peak-dense | 1646kPa | 1488kPa | +10.6 % | Ours 1646 kPaPublished 1488 kPa+10.6 % | Deviation | |
| ||||||
1 m x 1 m plane-strain T6 sample, isotropic p_0 = 100 kPa then biaxial compression (sigma_x held; drained: sigma_y +90 kPa; undrained-a with Biot K_w = 2e6 kPa: total sigma_y +36 kPa), NorSand through the phase driver v… m17-norsand-fe-plane-strain-vs-element · Self-check | 7.227e-9relative | 0relative | +7.2e-7 % | Ours 7.227e-9 relativePublished 0 relative+7.2e-7 % | Pass | |
| ||||||
Cited validation suites
cam-clay-triaxial-web-validationValidation for the Modified Cam-Clay integrator (`cam-clay-triaxial.ts`).20 passing
Analyses validated: cam-clay-triaxial, soil-models
- PassM = 6sinφ/(3−sinφ): φ_cs=20° → M≈0.772
- PassM = 6sinφ/(3−sinφ): φ_cs=25.4° → M≈1.0008
- PassM = 6sinφ/(3−sinφ): φ_cs=30° → M≈1.2
- PassM = 6sinφ/(3−sinφ): φ_cs=33.4° → M≈1.3484
- PassNCL void ratio at p′=50: e = N−λ·ln p′ −1
- PassNCL void ratio at p′=100: e = N−λ·ln p′ −1
- PassNCL void ratio at p′=200: e = N−λ·ln p′ −1
- PassNCL void ratio at p′=400: e = N−λ·ln p′ −1
- PassNC CIU su/p′₀ = (M/2)(½)^Λ: M=0.89, λ=0.16, κ=0.03
- PassNC CIU su/p′₀ = (M/2)(½)^Λ: M=1, λ=0.2, κ=0.04
- PassNC CIU su/p′₀ = (M/2)(½)^Λ: M=1.2, λ=0.1, κ=0.02
- PassNC CIU su/p′₀ = (M/2)(½)^Λ: M=0.95, λ=0.25, κ=0.05
- Passyield ellipse: CSL intersects at p′=p_c/2, q=M·p_c/2
- PassMCC elastic step (inside the ellipse) is non-plastic
- PassNC sample (p=pc) yields under shear (plastic)
- Passderived κ puts the MCC critical-state line at the printed Γ = 3.16 (hand check, not counted)
- PassAtkinson & Bransby Ex 10-1 (p. 193): undrained NC test v₀ = 2.0517, q_f = 240, p_f = 255
- PassAtkinson & Bransby Ex 10-2 (pp. 195–196): drained NC test v_f = 1.886, ε_v = 8.09 %
- PassAtkinson & Bransby Ex 11-2 (pp. 229–230), sample A: q_f = 239, u_f = 225 kN/m²
- Passthe published-value tally is 7 distinct printed numbers from 1 source; PARTIAL (short of 20 by 13)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
constitutive-tools-web-validationconstitutive-tools-web-validation.test.ts15 passing
Analyses validated: cam-clay-triaxial, drucker-prager, duncan-chang, ngi-adp, soft-soil-creep, von-mises
- PassDrucker-Prager: cone constants equal the de Souza Neto §8.3 compression-corner match (6 anchors)
- PassDrucker-Prager: the matched cone reproduces the Mohr-Coulomb triaxial deviator EXACTLY (4 anchors)
- PassDrucker-Prager: φ=30°, c=10 kPa, σ₃=100 kPa → q_f = 234.641 kPa, and ψ sets β independently
- PassDuncan-Chang: E_i, q_f and q_ult on the registry defaults (K=300, n=0.5, σ₃=100 kPa)
- PassDuncan-Chang: the hyperbola q = ε/(1/E_i + ε/q_ult) at 1 % axial strain
- PassDuncan-Chang: the model behaves as Duncan & Chang describe (5 monotonicity anchors)
- PassNGI-ADP: the three anisotropic strengths are the declared ratios of s_u^A (4 anchors)
- PassNGI-ADP: anisotropy ordering and the isotropic limit (5 anchors)
- PassCam-Clay: M, Λ and p′_cs/p′₀ = (½)^Λ on the registry defaults (5 anchors)
- PassCam-Clay: s_u/p′₀ = ½ M (½)^Λ, so the undrained strength follows from the CSL alone
- PassSoft-Soil-Creep: λ*, κ*, μ* and M from the published definitions (6 anchors)
- PassSoft-Soil-Creep: creep strain per log-decade is μ*·ln10, and λ* > κ* > μ* for a real clay
- Passvon Mises: q from the principal stresses, plus the yield decision (6 anchors)
- Passevery constitutive tool returns finite numbers on its defaults and at parameter extremes
- Passduncan-chang: σ₃ = 0 is an UNCONFINED test, which the hyperbolic fit cannot represent
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
dp-material-point-web-validationWeb-benchmark validation for the Drucker-Prager material-point integrator (`dp-material-point.ts`).24 passing
Analyses validated: mohr-coulomb, soil-models
- PassDP q_f == MC q_f (compression corner): σ3=50, c=10, φ=30
- PassDP q_f == MC q_f (compression corner): σ3=100, c=10, φ=30
- PassDP q_f == MC q_f (compression corner): σ3=200, c=10, φ=30
- PassDP q_f == MC q_f (compression corner): σ3=100, c=0, φ=35
- PassDP q_f == MC q_f (compression corner): σ3=200, c=0, φ=35
- PassDP q_f == MC q_f (compression corner): σ3=300, c=0, φ=40
- PassDP q_f == MC q_f (compression corner): σ3=100, c=25, φ=0
- PassDP q_f == MC q_f (compression corner): σ3=50, c=50, φ=0
- PassDP q_f == MC q_f (compression corner): σ3=300, c=1, φ=34
- PassDP q_f == MC q_f (compression corner): σ3=10, c=5, φ=25
- PassDP q_f == MC q_f (compression corner): σ3=500, c=20, φ=38
- PassDP apex return → p = −c·cotφ, c=10, φ=30
- PassDP apex return → p = −c·cotφ, c=20, φ=35
- PassDP elastic step below yield returns exact elastic stress
- PassDP plastic return lands on the cone (f≈0), φ=20
- PassDP plastic return lands on the cone (f≈0), φ=30
- PassDP plastic return lands on the cone (f≈0), φ=40
- PassDP dilatancy (ψ>0) raises mean stress vs ψ=0
- PassDP drained triaxial integrates to q_f (multi-step), φ=30, c=10
- PassDP drained triaxial integrates to q_f (multi-step), φ=35, c=0
- Passgeneral DP (axis-aligned) equals the principal integrator
- Passgeneral DP return lands on the cone for a shear state, φ=25
- Passgeneral DP return lands on the cone for a shear state, φ=35
- Passgeneral DP objectivity: I1 invariant across shear plane
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
drucker-prager-web-validationValidation for the Drucker-Prager cone runner (`dp-material-point.ts`: `computeDruckerPragerRunner`, `dpConstants`, `dpTriaxialFailure`) — slug `drucker-prager`.5 passing
Analyses validated: drucker-prager
- PassLambe & Whitman Ex 11.1 (p. 140): DP compression failure σ1f = σ3 + q_f at the printed φ, four tests
- PassCraig Ex 5.2 (p. 178): printed σ′1 lies in the ±0.5° bracket of the printed secant φ′
- PassPLAXIS 3DF §2.4 and COMSOL Table 2: DP compression failure stress 372.9 and 1064.9 kPa
- Passde Souza Neto et al. §8.4.3: plane-strain footing limit load of the compression-matched cone, P_lim/c ≈ 35.7
- Passthe published-value tally is 10 distinct printed numbers from 5 sources; PARTIAL (short of 20 by 10)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
duncan-chang-web-validationValidation for the Duncan-Chang hyperbolic model (`duncan-chang.ts`).10 passing
Analyses validated: duncan-chang, soil-models
- PassMC failure deviator matches the closed form
- Passinitial tangent modulus Ei = K·pa·(σ3/pa)^n
- Passinitial slope of q(ε) equals Ei
- Passdeviator asymptotes to (σ1−σ3)_ult = qf/Rf
- Passtangent modulus: Et=Ei at SL=0, (1−Rf)²Ei at SL=1
- Passdeviator always below failure for finite strain
- PassDuncan-Chang MC failure deviator q_f = (2c·cosφ + 2σ₃·sinφ)/(1−sinφ) — cited sweep
- PassDuncan-Chang initial tangent modulus Ei = K·pa·(σ₃/pa)^n — cited sweep
- PassDuncan-Chang tangent modulus Et = (1−Rf·SL)²·Ei — cited SL sweep (σ₃=100)
- PassDuncan-Chang hyperbolic q(ε) = ε/(1/Ei + ε·Rf/q_f) — cited values (σ₃=100)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-interface-2d-web-validationValidation for the 2-D SSI elements embedded in the continuum (`fe-interface-2d.ts`): the zero-thickness Goodman INTERFACE (elastic normal/shear + Mohr-Coulomb slip) and the Euler-Bernoulli PLATE/beam sharing continuum node DOFs.6 passing
Analyses validated: not attributed by the manifest
- Passinterface elastic shear transfer: slip = τ/k_s, σ_n from the applied normal load (below slip)
- Passinterface Mohr-Coulomb slip: shear capped at c + σ_n·tanδ
- Passfrictionless interface (c=0, δ=0) slips under any shear
- Passplate cantilever: tip deflection PL³/3EI and rotation PL²/2EI (Euler-Bernoulli)
- Passplate axial: u = PL/EA
- Passinterface + continuum solve converges (slip state settles)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hardening-soil-double-web-validationValidation for the FULL double-hardening Hardening-Soil integrator (`hardening-soil-double.ts`).7 passing
Analyses validated: hardening-soil
- PassHS-double: MC failure cap σ₁_f = 1064.9 kPa at σ₃=300 (COMSOL 6.3 Table 2, closed-form MC value)
- PassHS-double WEB: E₅₀(σ₃) matches the HS power law (100→20 MPa, 300→40.6 MPa)
- PassHS-double: secant modulus at q_f/2 = E₅₀ (self-consistent hardening)
- PassHS-double: primary backbone matches the closed-form hardening-soil SoilTest
- PassHS-double: unload–reload loop stiffness ≈ E_ur ≫ loading secant (Schanz-Vermeer)
- PassHS-double: plastic shear/volumetric strain tracked; dense sand dilates near failure
- PassHS-double CAP: oedometer plastic compression + K₀ᴺᶜ = 1 − sinφ
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hardening-soil-web-validationValidation for the Hardening-Soil (HS) SoilTest engine (`hardening-soil.ts`).21 passing
Analyses validated: hardening-soil
- PassHS web A1: E50(σ3=pref) = E50ref [Berlin]
- PassHS web A2: Eur(σ3=pref) = Eurref [Berlin]
- PassHS web A4: Ei = 2·E50/(2−Rf) = 81.818 MPa [Berlin σ3=100]
- PassHS web A5–A8: E50 stress scaling [Berlin]
- PassHS web A9–A13: qf = 2(c·cosφ+σ3·sinφ)/(1−sinφ) [Berlin]
- PassHS web: σ1f = σ3 + qf [Berlin σ3=50,200]
- PassHS web A14: Ei = 119.324 MPa [Berlin σ3=200]
- PassHS web A15: Eur = 327.67 MPa [Berlin σ3=300]
- PassHS web A16: Eur/E50 = 4.0 stress-independent [Berlin]
- PassHS web A17: φ_cv = 30.80° [Berlin φ=35,ψ=5]
- PassHS web A18: COMSOL Table 2 σ1f = 1064.9 kPa [σ3=300] (MC cap, not SVB)
- PassHS web A19–A21: Monterey Ei = 2·E50/(2−Rf) identity [identity, parameter set untraced]
- PassHS web A22: secant modulus at qf/2 = E50 (E50_secant_error ≈ 0)
- PassHS web A23: Ei/E50 = 2/(2−Rf) across Rf
- PassHS web A3: Eoed(σ=pref) = Eoedref [Berlin oedometer]
- PassPLAXIS 3DF Validation Manual §2.4: HS triaxial failure σ1 = 372.9 (theory) / 373.3 (FE), σ3 = 100
- PassCOMSOL Table 2: σ1f = 1064.9 kPa (MC cap, independent of E50, m, Rf)
- PassPLAXIS Material Models Manual (2015) Tables 13.1/13.2/13.13: K0nc = 1 − sinφ at φ = 30, 34, 35, 38, 40, 41°
- Passdefault E_ur = 3·E50 reproduces the printed E_ur columns (PMM Table 13.1, RS3 Table 15.1)
- PassPLAXIS default values: p_ref = 100, R_f = 0.9, E_oed = E50 (PMM 2015 pp. 7, 66, 71)
- Passthe published-value tally is 16 distinct printed numbers; PARTIAL (short of 20 by 4)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hs-cap-oedometer-web-validationValidation for the HS CAP OEDOMETER / K₀ BRANCH — the combined shear+cap axisymmetric return-map (`integrateHsAxiStep` / `hsOedometerRun`) and the implicit two-parameter (M, K_s/K_c) ← (K₀ᴺᶜ, E_oed^ref) calibration (`calibrateHsCap`).6 passing
Analyses validated: not attributed by the manifest
- PassEXACT limit — cap off (K_s/K_c ≤ 1) reproduces the validated shear-only triaxial
- PassEXACT limit — isotropic strain keeps the deviator exactly zero (axisymmetric cap flow)
- Passimplicit calibration reproduces BOTH K₀ᴺᶜ and E_oed^ref
- PassINDEPENDENT cross-check: E_oed(σv) matches the validated computeHsDouble power law
- PassK₀ stays constant along NC loading (a radial stress path — the calibrated-cap signature)
- Passconsistent-γ^p / p_p initialisers leave BOTH surfaces exactly satisfied at a K₀ state
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hs-cap-web-validationValidation for the HS VOLUMETRIC CAP (compaction hardening) — the second HS yield surface (`hs-material-point.ts`: hsCapParams / integrateHardeningSoilVolumetric / hsIsotropicCompression).7 passing
Analyses validated: not attributed by the manifest
- Passcap parameters: K_s^ref = E_ur^ref/(3(1−2ν_ur)) and K_s/K_c > 1 (Eq 6.23)
- Passcap DISABLED when E_oed^ref omitted (shear-hardening only, no regression)
- PassK_c = K_s^ref/(K_s/K_c) and K_s = K_s^ref at the reference pressure (Eq 6.22)
- Passboth moduli follow the (p/p_ref)^m stress-dependency
- Passpre-consolidation (OCR): elastic inside the cap, plastic once p reaches p_p
- Passp_p hardens to track the maximum mean stress under virgin (NC) loading
- Passisotropic loading is softer than swelling (K_c < K_s) — the defining compaction-hardening signature
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hs-material-point-web-validationValidation for the Hardening-Soil material-point integrator (`hs-material-point.ts`) — the general SVB return-map (shear/cone hardening) that the 2-D FE will use.12 passing
Analyses validated: not attributed by the manifest
- PassHS return-map reproduces the SVB drained-triaxial hyperbola at σ₃=100 kPa (<3%)
- PassHS return-map reproduces the SVB drained-triaxial hyperbola at σ₃=200 kPa (<3%)
- PassHS return-map reproduces the SVB drained-triaxial hyperbola at σ₃=300 kPa (<3%)
- PassHS return-map reproduces the SVB drained-triaxial hyperbola at σ₃=600 kPa (<3%)
- Passfailure deviator = MC: σ₁_f(σ₃=300) = 1064.9 kPa (COMSOL 6.3 Table 2 closed-form MC value, not an SVB number)
- Passthe driven deviator approaches the MC failure envelope q_f at large strain
- Passsecant modulus at q_f/2 equals E₅₀(σ₃) (the HS E₅₀ definition)
- Passisotropic (deviator-free) loading stays elastic on the shear surface (γ^p unchanged)
- Passmobilised friction hardens with plastic shear strain toward the peak φ
- Passhigher confining pressure → higher failure deviator and stiffer response
- Passgeneral Cartesian material point: isotropic + deviatoric strain returns a coaxial plastic state
- Passgeneral Cartesian material point handles an off-axis shear strain increment (finite, hardening)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hs-small-fe-web-validationValidation for the HS-Small small-strain constitutive OVERLAY (`hs-small-stiffness.ts`): the stress-dependent very-small-strain modulus G0(σ3) and the simple-shear constitutive integrator `hsSmallSimpleShear` — the per-integration-point st…5 passing
Analyses validated: hs-small, soil-models
- Passtangent integrates exactly to the Hardin-Drnevich secant (below the G_ur cut-off)
- PassG_s(γ0.7)/G0 = 0.722 (definition of γ0.7)
- Passstress-dependent G0(σ3) follows the (σ3/p_ref)^m power law
- Passtangent floors at G_ur beyond the cut-off strain (never softer than unload-reload)
- Passsecant modulus degrades monotonically with shear strain
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hs-small-general-web-validationValidation for the GENERAL-STRESS (Voigt6) HS-Small material point `integrateHsSmallGeneral` — the FE Gauss-point entry that couples the Benz (2007) Small-Strain Overlay to the Hardening-Soil return map.5 passing
Analyses validated: hs-small
- PassHS-Small with G0 = Gur^ref reduces to plain HS (1e-9)
- PassHS-Small: an elastic (inside-the-cone) path follows the reloading curve G0/(1 + aγ/(2γ0.7)) (γ = 3/2 εq)
- PassENG-2: HS-Small γHist of an undrained triaxial increment equals ε1 − ε3 (PLAXIS Eq. 7.6)
- PassHS-Small: mobilised shear modulus floors at the HS Eur modulus at large strain
- PassHS-Small: general shear-coupled increment returns a finite stress
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hs-small-kernel-law-web-validationHS-small (Benz 2007) — the kernel's law in the TypeScript twin (KB-2, 12 Nov 2026).10 passing
Analyses validated: hs-small, soil-models
- PassG1 small-strain limit: G = G0 exactly below γHist 1e-6; G → G0 as γ → 0 on the reloading curve
- PassG2 first loading: Gm·Gur of a virgin step is the Hardin–Drnevich secant G0/(1 + 0.385γ/γ0.7)
- PassG2 kernel expectations (hs_small_gamma_hist.rs): γHist measure, history accumulation, Gm over [γ9, γ10]
- PassG3 Gur cut-off: Gur beyond γc(reload); the straddling step integrates the cut-off; never below Gur
- PassG3 1-D calculator: the secant beyond γc integrates the tangent cut-off (Benz Fig. 7.6), = 31 494 kPa at γ = 2e-3
- PassG4 Masing after one reversal: back to G0 on the 2·γ0.7 curve; Gm keeps its minimum
- PassG5 hᵢ attenuation: one drained triaxial step from 100 kPa isotropic matches the hand form to 1e-6
- PassG6 KB-2a: from an isotropic state HS-small is never softer than plain HS, and ≥ 3× stiffer at γxy = 1e-5
- PassG7 G0 = Gur^ref: the overlay is inert and HS-small is plain HS over a path (1e-9)
- PassG8 refusals: the kernel’s HsParams::validate rules
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
hs-small-stiffness-web-validationValidation for the HS-Small small-strain stiffness overlay (`hs-small-stiffness.ts`).5 passing
Analyses validated: hs-small, soil-models
- PassG_s → G0 as γ → 0
- PassG_s = 0.722·G0 exactly at γ = γ0.7 (definition)
- Passtangent modulus below secant, and G_t = G0/(1+aγ/γ07)²
- Passmonotonic decay of G_s with increasing γ
- Passcut-off at G_ur: G never below G_ur; cut-off strain consistent
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mc-general-stress-web-validationWeb-benchmark validation for the symmetric-3×3 eigensolver + general-stress (Cartesian) Mohr-Coulomb material point (`tensor-3x3.ts` + the general MC entry in `mc-material-point.ts`).9 passing
Analyses validated: not attributed by the manifest
- PasseigSym3 of a diagonal matrix returns sorted diagonal
- PasseigSym3 of a 2×2 shear block: [[2,1],[1,2]] → 3 and 1
- PasseigSym3 reconstruct: Σ λ n⊗n recovers the original tensor
- Passgeneral MC (axis-aligned) equals the principal integrator
- Passgeneral MC return lands on the surface for a shear state, φ=20
- Passgeneral MC return lands on the surface for a shear state, φ=30
- Passgeneral MC return lands on the surface for a shear state, φ=40
- Passobjectivity: I1 and J2 of the returned stress are rotation-invariant
- Passgeneral MC small step stays elastic
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mc-material-point-web-validationWeb-benchmark validation for the Mohr-Coulomb material-point integrator (`mc-material-point.ts`).23 passing
Analyses validated: mohr-coulomb
- PassMC failure deviator matches closed form: σ3=50, c=10, φ=30
- PassMC failure deviator matches closed form: σ3=100, c=10, φ=30
- PassMC failure deviator matches closed form: σ3=200, c=10, φ=30
- PassMC failure deviator matches closed form: σ3=100, c=0, φ=35
- PassMC failure deviator matches closed form: σ3=200, c=0, φ=35
- PassMC failure deviator matches closed form: σ3=300, c=0, φ=40
- PassMC failure deviator matches closed form: σ3=100, c=25, φ=0
- PassMC failure deviator matches closed form: σ3=50, c=50, φ=0
- PassMC failure deviator matches closed form: σ3=300, c=1, φ=34
- PassMC failure deviator matches closed form: σ3=10, c=5, φ=25
- PassMC failure deviator matches closed form: σ3=500, c=20, φ=38
- PassCOMSOL 6.3 Table 2 MC benchmark: σ3=300, φ=34°, c=1 → σ1f ≈ 1064.9 kPa
- Passelastic step below yield returns the exact elastic stress (no plastic)
- Passelastic deviatoric step just inside the surface stays elastic
- Passplastic return lands ON the yield surface (f≈0), φ=20
- Passplastic return lands ON the yield surface (f≈0), φ=30
- Passplastic return lands ON the yield surface (f≈0), φ=40
- Passreturned stress satisfies the MC criterion σ1 = σ3·Nφ + 2c√Nφ
- Passapex return: isotropic tensile pull → σ = −c·cotφ, c=10, φ=30
- Passapex return: isotropic tensile pull → σ = −c·cotφ, c=20, φ=35
- Passassociated (ψ=φ) dilates; ψ=0 is (near) isochoric plastic flow
- Passdrained triaxial integrates to q_f (multi-step), φ=30, c=10
- Passdrained triaxial integrates to q_f (multi-step), φ=35, c=0
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mcc-general-web-validationValidation for the GENERAL-STRESS (Voigt6) Modified Cam-Clay material point `integrateModifiedCamClayGeneral` — the FE Gauss-point entry that lets the general T6 solver run critical-state plasticity.9 passing
Analyses validated: cam-clay-triaxial, soil-models
- PassMCC general ≡ triaxial mccStep on a triaxial path (dilatant shear)
- PassMCC general ≡ triaxial mccStep on a triaxial path (isotropic compression)
- PassMCC general ≡ triaxial mccStep on a triaxial path (near-undrained shear)
- PassMCC general undrained NC critical state (φ_cs=25.4°)
- PassMCC general undrained NC critical state (φ_cs=30°)
- PassMCC general undrained NC critical state (φ_cs=22°)
- PassMCC general elastic step is non-plastic and exact
- PassMCC general: plastic state lies on the yield surface (triaxial)
- PassMCC general: plastic state on the yield surface under shear strain
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mohr-coulomb-web-validationPUBLISHED-VALUES(mohr-coulomb): 17 -- distinct published values for this engine (engine-level total, declared once); re-run author's strict count: the 21 includes 4 Lambe & Whitman sigma1f/ratio pairs that are the same four experiments pri…15 passing
Analyses validated: mohr-coulomb
- PassN_φ = tan²(45° + φ/2) — the published flow factor at 8 friction angles
- Passσ1f = σ3·N_φ + 2c·√N_φ — 12 published failure states
- Passundrained clay (φ = 0): the deviator at failure is 2c, independent of confining stress
- Passunconfined compressive strength q_u = 2c·√N_φ
- Passfailure-plane geometry: θ_f = 45° + φ/2, and σ_n / τ_f from the same Mohr circle
- Passmonotonicity and finiteness across the admissible parameter range
- PassLambe & Whitman Ex 11.1 (p. 140): σ1f from printed σ3f and φ, four tests
- PassLambe & Whitman Ex 11.1 (p. 140): θcr = 45° + φ/2 = 66° for the average φ = 42.1°
- PassLambe & Whitman Ex 11.2 (p. 142): sinφ = tanα = 0.675 on the p–q diagram, φ = 42.5°
- PassCraig Ex 5.2 (p. 178): printed σ′1 lies in the ±0.5° bracket of the printed secant φ′
- PassLambe & Whitman Fig. 21.6 (p. 308): p–q intercept a = c·cosφ′ = 6.9 kN/m² for c = 7.4, φ′ = 21.5°
- PassPLAXIS 3DF Validation Manual §2.3 (pp. 2-5/2-6): MC bi-axial failure stress 6.46 (theory), 6.48 (FE)
- PassPLAXIS 3DF Validation Manual §2.4 (pp. 2-7/2-8): 372.9 and 373.3 compression, 26.1 extension
- PassCOMSOL HS triaxial Table 2: MC failure stress 1064.9 kPa compression, 83.7 kPa extension (c = 1, φ = 34°, σ3 = 300)
- Passthe published-value tally is 21 distinct printed numbers from 4 sources
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
ngi-adp-web-validationWeb-benchmark validation for the NGI-ADP anisotropic undrained material point (`ngi-adp.ts`).15 passing
Analyses validated: ngi-adp
- PassNGI-ADP ellipse constants RA, RB, RD (Grimstad 2012 Eq 12.22)
- PassNGI-ADP Active strength → suA (P1=40, P2=100)
- PassNGI-ADP Passive strength → suP (P1=16, P2=60)
- PassNGI-ADP DSS strength → suDSS (P1=26.4, P2=80)
- PassNGI-ADP f=0 at Active/Passive/DSS failure points (Eq 12.3)
- PassNGI-ADP isotropic → Tresca: su=25 ⇒ q=2su=50
- PassNGI-ADP isotropic → Tresca: su=50 ⇒ q=2su=100
- PassNGI-ADP isotropic → Tresca: su=120 ⇒ q=2su=240
- PassNGI-ADP τ0 = ½σ'v0(1−K0)
- PassNGI-ADP hardening κ(γp) endpoints + peak (Eq 12.2)
- PassNGI-ADP envelope sweep — all points satisfy f=0
- PassNGI-ADP interior f<0, exterior f>0
- PassNGI-ADP M from φ (6sinφ/(3−sinφ))
- PassNGI-ADP integrator: monotone vertical shear → peak τ = suA (Active)
- PassNGI-ADP integrator: pure shear at the ellipse-centre deviator → peak τxy = suDSS
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
soft-soil-creep-web-validationWeb-benchmark validation for the Soft-Soil-Creep material point (`soft-soil-creep.ts`).15 passing
Analyses validated: soft-soil-creep
- PassSSC M = 6sinφ/(3−sinφ) (Eq 9.19)
- PassSSC φ↔M round-trip (inverse of Eq 9.19)
- PassSSC parameter conversion Cc/Cs/Cα/e0 → λ*,κ*,μ* (Eqs 9.6/9.9/9.22)
- PassSSC parameter conversion — soft-clay set 2
- PassSSC creep strain per log-decade = μ*·ln10 = Cα/(1+e0) (Mesri & Godlewski)
- PassSSC Buisman 1-D creep: t′=τc → μ*·ln2 ; per decade → μ*·ln10
- PassSSC creep rate at NC (OCR=1) = μ*/τ (Eq 9.23)
- PassSSC creep rate decreases with OCR (over-consolidation slows creep)
- PassSSC μ*=0 → zero creep rate (Soft-Soil limit)
- PassSSC ageing pre-consolidation grows with creep (Bjerrum)
- PassSSC equivalent stress (Eq 9.18): q=0 → p^eq=p′ ; on CSL q=Mp′ → 2p′
- PassSSC elastic swelling κ*·ln(p′/p′0) (Eq 9.28)
- PassSSC oedometer creep ODE integrates to Buisman μ*·ln(1+t/τ)
- PassSSC oedometer late-time slope → μ*·ln10 per decade
- PassSSC step μ*=0: pure elastic κ* response, no creep
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
soil-calibration-web-validationValidation for the SoilTest calibration lab (`soil-calibration.ts`).14 passing
Analyses validated: mohr-coulomb, soil-calibration
- Passfit MC recovers c=15, φ=28 from clean triaxial points
- Passfit MC recovers c=0, φ=35 from clean triaxial points
- Passfit MC recovers c=25, φ=20 from clean triaxial points
- Passfit MC recovers c=5, φ=40 from clean triaxial points
- Passfit MC is robust to measurement noise
- Passfit undrained su = q_f/2
- Passfit oedometer recovers Cc and Cr
- Passfit E50 = (q_f/2)/ε at half failure
- Passfit CSL M from critical-state points
- Passpublished: Craig Example 5.4(a) UU triaxial → c_u = 85 kPa, φ_u = 0
- Passpublished: Craig Example 5.4(b) CD triaxial → c′ = 0, φ′ = 27°
- Passpublished: Craig Example 4.1 oedometer Table 4.1 → C_c = 0.31 on the linear part
- Passpublished: Das Example 2.12 → C_c = 0.333 from (140 kPa, e 0.92) and (212 kPa, e 0.86)
- Passpublished: Lambe & Whitman Example 11.1 — four triaxial peaks on dense sand → φ = 42.1°, c = 0
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
soil-structure-interface-web-validationWEB-BENCHMARK validation for the soil-structure interface (Goodman joint) engine.8 passing
Analyses validated: soil-structure-interface
- PassSSI web A1–A6: interface friction δ = atan(R_inter·tanφ)
- PassSSI web A7–A9: interface adhesion c_i = R_inter·c
- PassSSI web A10–A13: τ_max = c_i + σ_n·tanδ
- PassSSI web A14: R_inter=1 ⇒ interface strength = soil strength
- PassSSI web A15–A17: strength reduction ≈ R_inter (c=0)
- PassSSI web A18–A19: Potyondy steel/sand δ/φ in [0.5, 0.8]
- PassSSI web A20: Potyondy concrete/sand δ/φ ≈ 0.84–1.0
- PassSSI web A21: Goodman elastic-plastic load-slip (slope k_s, plateau τ_max)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
ssc-general-web-validationValidation for the GENERAL-STRESS (Voigt6) Soft-Soil-Creep material point `integrateSoftSoilCreepGeneral` — the FE Gauss-point entry for time-dependent secondary compression / creep, so the general T6 solver can run SSC.6 passing
Analyses validated: soft-soil-creep
- PassSSC general ≡ (p′,q) sscStep on a triaxial path (compression + shear)
- PassSSC general ≡ (p′,q) sscStep on a triaxial path (isotropic compression)
- PassSSC general: NC (OCR=1) creep rate is μ*/τ
- PassSSC general: μ*=0 gives no creep and an exact elastic step
- PassSSC general: pre-consolidation ages upward under sustained creep
- PassSSC general: shear-coupled increment returns a finite stress
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
stress-path-web-validationValidation for `stress-path` — p-q (Cambridge) and s-t (MIT) stress-path invariants, mobilised friction and the failure check (`stress-path.ts`).7 passing
Analyses validated: stress-path
- PassHead & Epps Fig. 16.14(a): s′ and t at 0.67, 1.12 and 1.54 % strain
- PassHead & Epps Fig. 16.14(a): s′ and t at 2.18 and 3.06 % strain
- PassL&W Example 11.1: printed p = ½(σ1 + σ3) and q = ½(σ1 − σ3) for the four peak states
- PassL&W Example 11.1: mobilised friction at peak = 42.2°, 41.6°, 42.7°, 42.1° (c = 0)
- PassCraig Example 5.2: secant φ′ of circles (a), (b), (c) = 35°, 33°, 31°
- PassCraig Example 5.6: drained failure point q_f = 374, p′f = 425, η = M = 0.88, path slope 3
- PassCraig 7th Solutions CU test: printed s′ = 411, 402, 389, 351, 326 and t = 40, 79, 107, 139, 159 kPa
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
triaxial-csl-web-validationrecords a differencePUBLISHED-VALUES(triaxial-csl): 13 -- distinct published values for this engine (engine-level total, declared once); re-run author's count: of 21 values only 13 are failure states in and a book answer out; 8 feed states built on a publishe…12 passing
Analyses validated: triaxial-csl
- PassL&W Example 11.1: four peak states → φ_f average 42.1°
- PassL&W Weald clay: Kf line a = 6.9, α = 20.3° → φ = 21.5°, c = 7.4 kN/m²
- PassL&W NC Weald clay: Kf line through the origin with α = 20½° → φ = 22°, no cohesion
- PassHead & Epps Fig. 16.14(b): Kf line θ = 20.5°, t0 = 12 kPa → φ′ = 22°, c′ = 13 kPa
- PassCraig 8th Ex 5.2: effective-stress failure states → tangent c′ = 20 kPa, φ′ = 29° (graphical, 200-300 kPa)
- PassCraig 8th Ex 5.4(a): UU states (370,200), (564,400), (772,600) → cu = 85 kPa, φu = 0
- PassCraig 8th Ex 5.4(b): drained states (530,200), (1091,400), (1620,600) → c′ = 0, φ′ = 27°
- PassCraig 8th Ex 5.6: states on q = 0.88 p′ → φ′cv = 23°
- PassCraig 7th Solutions Q4.2: sand σ3 = 100…800, σ1 − σ3 = 452…3624 → φ′ = 44°
- PassCraig 7th Solutions Q4.3: UU σ3 = 200, 400, 600, σ1 − σ3 = 222, 218, 220 → cu = 110 kN/m², φu = 0
- PassCraig 7th Solutions Q4.4: a′ = 13 kN/m², α′ = 26° → φ′ = 29°, c′ = 15 kN/m²
- PassCraig 7th Solutions Q4.5: CU clay effective states (171,68), (333,131), (503,198), (679,269) → c′ = 0, φ′ = 25½°
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
von-mises-material-point-web-validationValidation for the von Mises (J2) radial-return material point (`von-mises-material-point.ts`: `vonMisesQ`, `integrateVonMises`) — slug `von-mises`.9 passing
Analyses validated: von-mises
- Passelastic below yield: pure shear stays elastic and q correct
- Passafter plastic return, q = σ_y exactly (multiple strain paths)
- Passplastic flow is isochoric: mean stress unchanged by the return
- Passuniaxial: yields when axial stress reaches σ_y
- PassvonMisesQ of a uniaxial stress equals the axial stress
- Passde Souza Neto et al. §7.5.1 (p. 246): cylinder limit pressure P_lim = Y·ln(b/a) = 0.19209 GPa
- Passde Souza Neto et al. §7.5.1 (p. 247): at P = 0.18 GPa the plastic front is at c ≈ 159.79 mm
- Passde Souza Neto et al. §7.5.2 (p. 248): sphere limit pressure P_lim = 2(σ_θ−σ_r)_y·ln(b/a) = 0.33271 GPa
- Passthe published-value tally is 3 distinct printed numbers from 1 source; PARTIAL (short of 20 by 17)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Finite-element meshing, solvers and procedures
8 finite-element rows (2 superseded) · 0 closed-form problems · 17 validation suites
Finite-element solver registry
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
plaxis-verif-k5-set plaxis-verif-k5-set | — | — | — | Ours —Published —— | Superseded | |
| ||||||
plaxis-verif-v2-set plaxis-verif-v2-set | — | — | — | Ours —Published —— | Superseded | |
| ||||||
σ'yy = −Σγh and σ'xx = ν/(1−ν) σ'yy at 240 Gauss points; crest settlement ∫σ'yy/E_oed dy, two layers v-gravity-loading-layered-column | -0.046371kPa, m | -0.046371kPa, m | 0.00 % | Ours -0.046371 kPa, mPublished -0.046371 kPa, m0.00 % | Pass | |
| ||||||
crest displacement after a surcharge phase with reset: q Σh/E_oed; without reset: gravity + q Σh/E_oed v-reset-displacements-closed-form | [-0.031071, -0.077443] | [-0.031071, -0.077443] | [0, 0] % | Ours [-0.031071, -0.077443] mPublished [-0.031071, -0.077443] m[0, 0] % | Pass | |
| ||||||
r_e of the five levels v-rm-global-coarseness-r_e | [2, 1.33, 1, 0.67, 0.5] | [2, 1.33, 1, 0.67, 0.5] | 0.00 % | Ours [2, 1.33, 1, 0.67, 0.5]Published [2, 1.33, 1, 0.67, 0.5]0.00 % | Pass | |
| ||||||
l_e / (r_e · diagonal) v-rm-global-coarseness-le | 0.06 | 0.06 | 0.00 % | Ours 0.06Published 0.060.00 % | Pass | |
| ||||||
min interior angle of a 3-4-5 triangle via mesh2d::report::shape_stats (what the model screen prints as 'Min. angle') v-rocscience-mesh-quality-shape-stats · Self-check | 36.8699deg | 36.8699deg | 0.00 % | Ours 36.8699 degPublished 36.8699 deg0.00 % | Pass | |
| ||||||
element size rule l_e = r_e/20·diagonal on a 30 × 40 m box ('medium'); graded ceiling h(x)=min(l_e, f·l_e+0.5·d); area conservation v-rocscience-mesh-sizing · Self-check | 2.5m | 2.5m | 0.00 % | Ours 2.5 mPublished 2.5 m0.00 % | Pass | |
| ||||||
Cited validation suites
classical-closed-forms-web-validationWeb-benchmark validation for EIGHT classical closed-form runner engines.8 passing
Analyses validated: capillary-rise, circular-load-stress, darcy-velocity, effective-stress, k0-at-rest, layered-permeability, line-load-stress, strip-load-stress
- Passcircular-load-stress reproduces the Boussinesq on-axis solution
- Passline-load-stress reproduces Boussinesq Δσ_z = 2Pz³/[π(x² + z²)²]
- Passstrip-load-stress reproduces the strip solution and brackets the 2:1 method
- Passk0-at-rest follows Jaky K₀ = 1 − sin φ′ with the triangular thrust
- Passcapillary-rise follows h_c = C/(e·D₁₀) with consistent units
- Passdarcy-velocity separates discharge velocity from seepage velocity
- Passlayered-permeability gives the weighted arithmetic k_h and harmonic k_v
- Passeffective-stress is Terzaghi σ′ = σ − u with the water table respected
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-assemble-t6-web-validationValidation for the T6 global assembly/solver (`fe-assemble-t6.ts`).3 passing
Analyses validated: mesh-viewer
- PassT6 mesh builder dedups mid-side nodes by edge
- Passconstant-strain patch test on a T6 mesh (εxx=g)
- PassT6 reproduces a LINEAR strain field: u=(a·x², 0) → εxx = 2a·x
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-core-2d-web-validationWeb-benchmark validation for the TerraCore 2-D plane-strain FE core (`fe-core-2d.ts`).4 passing
Analyses validated: mesh-viewer
- PassplaneStrainD matches the closed form
- Passpatch test: uniform εxx reproduced exactly in every element
- Passuniaxial-strain confined ratio σyy/σxx = ν/(1−ν)
- Passrigid-body translation produces zero strain/stress
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-core-t6-web-validationValidation for the T6 quadratic element (`fe-core-t6.ts`).5 passing
Analyses validated: not attributed by the manifest
- PassJacobian: detJ = 2·area (=4) for the straight-sided T6
- Passconstant-strain patch: linear u=(g·x,0) → εxx=g at every Gauss point
- PassLINEAR strain patch: quadratic u=(a·x²,0) → εxx=2a·x EXACTLY (T6 advantage)
- Passshear quadratic field u=(0, b·x²) → γxy = 2b·x reproduced exactly
- PassT6 stiffness is symmetric and rigid-body/rank consistent
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-gravity-web-validationValidation for FE self-weight (gravity) loading (`gravityLoad` in fe-core-2d).2 passing
Analyses validated: geometry-editor, mesh-viewer
- Passself-weight column: σyy(y) = −γ·(H−y) (geostatic, linear with depth)
- Passconfined self-weight: horizontal stress σxx = K0·σyy with K0 = ν/(1−ν)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-plastic-2d-web-validationWeb-benchmark validation for the elasto-plastic FE solver (`fe-plastic-2d.ts`).6 passing
Analyses validated: mesh-viewer
- PassFE-plastic below yield equals the linear-elastic core
- PassFE element stress == material point (uniform εyy=-0.001)
- PassFE element stress == material point (uniform εyy=-0.003)
- PassFE element stress == material point (uniform εyy=-0.008)
- Passdeviatoric stress is capped by MC yield as shear strain increases
- Passyielded FE stress state satisfies MC on its principal stresses
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-plastic-cg-web-validationValidation for the matrix-free CG elasto-plastic solver (`fe-plastic-cg.ts`).3 passing
Analyses validated: geometry-editor, mesh-viewer
- PassCG plastic == material point on a uniform confined field
- PassCG plastic reaction equilibrium (top = −base)
- PassCG plastic solves a fine mesh (20×20) in reasonable time
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-plastic-general-web-validationValidation for the GENERAL incremental elasto-plastic T6 solver (`fe-plastic-general.ts`) — the unified-constitutive staged solver.7 passing
Analyses validated: mesh-viewer
- PassMC patch: single-increment Gauss stress equals integrateMohrCoulombGeneral exactly
- PassHS patch: N-increment Gauss stress equals the incrementally-integrated material point (state carry)
- PassHS behavioural: vertical stress magnitude grows monotonically and stays below MC failure
- PassDP patch: single-increment Gauss stress equals integrateDruckerPragerGeneral exactly
- PassVon Mises patch: single-increment Gauss stress equals integrateVonMises exactly (yielded)
- Passper-element regression: [MC] on 1 element equals the single-model solver exactly
- Passper-element dispatch: 2-element mesh, each element uses its OWN model (different E → different stress)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-plastic-t6-web-validationValidation for the T6 elasto-plastic solver (`fe-plastic-t6.ts`).5 passing
Analyses validated: mesh-viewer
- PassT6 plastic below yield equals the linear-elastic T6 core
- PassT6 element stress == material point (uniform εyy=-0.001)
- PassT6 element stress == material point (uniform εyy=-0.004)
- PassT6 deviator capped by MC under an increasing shear field
- PassT6 reaction (internalForce at fixed DOFs) balances the applied load
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-pressure-load-web-validationValidation for FE uniform-pressure loading (`uniformPressureLoad`).3 passing
Analyses validated: coupled-consolidation, geometry-editor, mesh-viewer
- Passtotal applied load = p · loaded width
- Passconfined block under uniform top pressure → σyy = −p everywhere
- Passpartial-width (footing) pressure applies only over the strip
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-solve-cg-web-validationValidation for the matrix-free CG FE solver (`fe-solve-cg.ts`).3 passing
Analyses validated: geometry-editor, mesh-viewer
- PassCG solver reproduces the dense solver (patch test, εxx=g)
- PassCG solver matches dense on a loaded (non-trivial) problem
- PassCG scales to a fine mesh (40×40 → ~3400 DOF) — dense would be too slow
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
geometry-editor-web-validationValidation for the `geometry-editor` tool — the polygon → PSLG → mesh path it drives through `pslgFromPolygons` + `generateMesh` (public API of mesh-cdt.ts only; the mesher is being rewritten concurrently, so every assertion below is an IN…8 passing
Analyses validated: coupled-consolidation, geometry-editor, mesh-viewer
- Passgeometry: a right triangle meshes to exactly ½·b·h (analytic area)
- Passgeometry: an L-shaped (concave) polygon — area 3 and area-weighted centroid (5/6, 5/6)
- Passgeometry: a square with a square hole — area = outer − hole, no element inside the hole
- Passgeometry: two stacked materials — conforming interface, correct tags by point-in-polygon, total area
- Passgeometry: the result does not depend on the order the polygons are drawn
- Passgeometry: polygon winding (CW vs CCW) does not change the meshed area
- Passgeometry: a translated model (real-world coordinates) meshes to the same area and element count
- Passgeometry: the mesher honours its minimum-angle target on an ordinary polygon
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
limit-analysis-fe-web-validationWEB-VALIDATION (the release rules gate) for `limit-analysis-fe.ts` — the FE strength-reduction slope FoS + displacement-controlled bearing-capacity limit load, built on the matrix-free CG elasto-plastic Mohr-Coulomb kernel.11 passing
Analyses validated: not attributed by the manifest
- PassreduceStrength: c_f = c/F and tanφ_f = tanφ/F (GL99 eqs 1–2)
- PassSRM slope: φ=30°, 2:1 → FoS ≈ tanφ/tanβ = 1.155 (within 3%)
- PassSRM slope: φ=35°, 2:1 → FoS ≈ 1.400 (within 3%)
- PassSRM slope: φ=45°, 2:1 → FoS ≈ 2.000 (within 3%)
- PassSRM slope: φ=40°, 1.5:1 → FoS ≈ 1.259 (achieved +~8%, within 12%)
- PassSRM slope: FoS increases with φ, and a gentler slope is safer
- PassBearing φ=0: mobilised N_c vs Prandtl 5.14 (CST over-predicts, honest)
- PassBearing φ=0: FE brackets Prandtl 5.14 on the load–settlement curve (±10%)
- PassBearing φ=0: refining the mesh reduces N_c toward Prandtl (from above)
- PassBearing φ=0: N_c independent of s_u; q_ult ∝ s_u (dimensional exactness)
- PassBearing φ=0: q_ult independent of footing width B (weightless Prandtl)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
linear-solver-cg-web-validationValidation for the CG linear solver (`linear-solver-cg.ts`).4 passing
Analyses validated: not attributed by the manifest
- PassCG solves a small dense SPD system to a known solution
- PassCG solves the 1-D Poisson system (tridiagonal −1,2,−1)
- PassCG residual decreases monotonically to tolerance
- PassCG matches a dense-solve reference on a random SPD system
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mesh-contour-web-validationValidation for the contouring backbone (`mesh-contour.ts`).5 passing
Analyses validated: coupled-consolidation, geometry-editor, mesh-viewer
- Passnodal averaging of a uniform element field is uniform
- Passiso-contour of a linear field lies exactly on the analytic line
- Passno iso-segments outside the field range
- PasscontourLevels returns evenly spaced interior levels
- Passa diagonal iso-line spans the domain (connected coverage)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mesh-delaunay-web-validationValidation for the TerraCore Delaunay mesher (`mesh-delaunay.ts`).7 passing
Analyses validated: not attributed by the manifest
- Passcircumcircle of a right triangle centres on the hypotenuse midpoint
- Passunit square triangulates into 2 triangles, total area 1
- PassDelaunay empty-circumcircle property holds (random set 1)
- PassDelaunay empty-circumcircle property holds (random set 2)
- PassDelaunay empty-circumcircle property holds (random set 3)
- Passtriangle count matches Euler for a 5×5 grid
- Passarea refinement of a square adds nodes, caps element area, stays Delaunay
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mesh-viewer-web-validationValidation for the `mesh-viewer` tool — what it DISPLAYS: element quality metrics, iso-contours of a nodal field, recovered (SPR) stress fields, and the elastic plane-strain solution underneath them.13 passing
Analyses validated: coupled-consolidation, geometry-editor, mesh-viewer
- Passquality: an equilateral triangle is perfect on every metric
- Passquality: a right-isosceles triangle — 45/45/90, edge ratio √2, radius ratio 2(√2 − 1)
- Passquality: a 30-60-90 triangle and a sliver rank in the right order
- Passquality: meshQuality on a structured CST grid — every element is 45/45/90
- Passtopology: rectMesh covers W×H exactly and satisfies Euler V − E + F = 1
- Passcontours: the iso-line of f = x at x = 0.3·W is the vertical line x = 0.3·W, length H
- Passcontours: a diagonal field f = x + y has straight 45° iso-lines; levels span the field range
- Passcontours: nodal averaging of a constant element field returns that constant at every node
- PassSPR: a linear element field f = 2 + 3x − 1.5y is recovered EXACTLY at every node (patch exactness)
- Passsolve: self-weight column — element σyy ≈ −γ(H − y_mid) and σxx ≈ K0·σyy with K0 = ν/(1 − ν)
- Passsolve: self-weight column — nodal settlement ≈ −γ(2Hy − y²)/(2M), M = E(1 − ν)/((1 + ν)(1 − 2ν))
- Passsolve: uniform strip pressure on a confined column gives σyy = −p everywhere and u_top = −pH/M
- Passsolve: the consistent gravity load vector sums to the total self-weight −γ·W·H
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Three-dimensional analysis
30 finite-element rows (3 deviations, 2 recorded) · 0 closed-form problems · 8 validation suites
Finite-element solver registry
Showing 30 of 30 rows.
| Problem | Ours | Published | Difference | Status | Details | |
|---|---|---|---|---|---|---|
max |u| at the end of the Initial (K0 procedure) phase k11-3d-tut1-a-k0-stationary | 0mm | 0mm | — | Ours 0 mmPublished 0 mm— | Pass | |
| ||||||
flexible control: centre settlement under 66 kPa surface pressure on the 36 m × 36 m footprint (elastic clay, same mesh and fixities) k11-3d-tut1-a-control-centre | 161.74mm | 160.2mm | +0.96 % | Ours 161.74 mmPublished 160.2 mm+0.96 % | Pass | |
| ||||||
flexible control: footprint-corner settlement (x = y = 18 m) under 66 kPa surface pressure (elastic clay) k11-3d-tut1-a-control-corner | 50.08mm | 45.14mm | +10.9 % | Ours 50.08 mmPublished 45.14 mm+10.9 % | Deviation | |
| ||||||
Tutorial 1 Case A as written (Table 1–1 Mohr–Coulomb clay): mean settlement of the basement underside (z = −2 m), base mesh k11-3d-tut1-a-basement-settlement | 99.23mm | 115.38mm | −14.0 % | Ours 99.23 mmPublished 115.38 mm−14.0 % | Deviation | |
| ||||||
Tutorial 1 Case A as written: mean basement-underside settlement, bisected mesh k11-3d-tut1-a-basement-settlement-fine · Self-check | 102.19mm | 115.38mm | −11.4 % | Ours 102.19 mmPublished 115.38 mm−11.4 % | Deviation | |
| ||||||
Tutorial 1 Case A as written: max |u| over the model at the end of Phase 1 'Building', base mesh k11-3d-tut1-a-max-displacement | 108.75mm | —mm | — | Ours 108.75 mmPublished — mm— | Pass | |
| ||||||
Tutorial 1 Case A as written: change of the mean basement settlement when every mesh interval is bisected k11-3d-tut1-a-mesh-change · Self-check | 2.98% | —% | — | Ours 2.98 %Published — %— | Pass | |
| ||||||
|HS − MC| top settlement of the oedometric column in the HS unloading/reloading range (OCR 4, σ′v0 −100 kPa, +10 kPa), m = 0.5 k11-3d-hs-linear-range | 7.772e-14% | 0% | — | Ours 7.772e-14 %Published 0 %— | Pass | |
| ||||||
NC oedometric strain, σ′v 50 → 400 kPa on the K0nc path, m = 0.5, finest step (stress ratio 1.005, 417 stages): % from the compression line k11-3d-hs-oedometer-m05 | 0.0642% | 0% | +0.06 % | Ours 0.0642 %Published 0 %+0.06 % | Pass | |
| ||||||
NC oedometric strain, σ′v 50 → 400 kPa on the K0nc path, m = 1, finest step (stress ratio 1.005, 417 stages): % from the compression line k11-3d-hs-oedometer-m1 | 0.1236% | 0% | +0.12 % | Ours 0.1236 %Published 0 %+0.12 % | Pass | |
| ||||||
Tutorial 1 Case A with the clay as Hardening Soil: mean settlement of the basement underside (z = −2 m), base mesh k11-3d-hs-tut1-basement | 75.228mm | —mm | — | Ours 75.228 mmPublished — mm— | Recorded, no published value | |
| ||||||
Tutorial 1 Case A: HS basement settlement relative to the Mohr–Coulomb run (row k11-3d-tut1-a-basement-settlement, 99.231 mm) k11-3d-hs-tut1-vs-mc | -24.19% | —% | — | Ours -24.19 %Published — %— | Recorded, no published value | |
| ||||||
|settlement − q·H/M0| of an OC (OCR 4) HS small column under a step of ε < 10⁻⁶ (σ′v0 −100 kPa, +0.05 kPa), m = 0.5 k11-3d-hss-small-strain-stiffness | 5.580e-11% | 0% | — | Ours 5.580e-11 %Published 0 %— | Pass | |
| ||||||
largest relative |σ_FE − σ_driver| of the HS small column against the model’s own point update along load (past the cap) – unload – reload, 11 stages k11-3d-hss-point-driver · Self-check | 9.800e-16% | 0% | — | Ours 9.800e-16 %Published 0 %— | Pass | |
| ||||||
largest relative settlement difference struct3d::run_stage (the structures stage) vs bvp3d on the HS small column over the 11-stage ladder k11-3d-hss-structures-stage · Self-check | 7.600e-10 | 0 | — | Ours 7.600e-10Published 0— | Pass | |
| ||||||
stability number γH/cu at collapse of an unsupported vertical cut (Tresca), from the 3-D safety phase (strength reduction) through the 3-D spec path, plane strain k11-3d-safety-vertical-cut | 3.9609 | 3.772–3.7845 | +4.84 % | Ours 3.9609Published 3.772–3.7845+4.84 % | Pass | |
| ||||||
wall-top horizontal displacement after the first dig (2 m), 3-D one-bay plane-strain twin vs the 2-D kernel k11-3d-wall-twin-dig1-top-ux · Self-check | -0.463mm | -0.452mm | +2.46 % | Ours -0.463 mmPublished -0.452 mm+2.46 % | Pass | |
| ||||||
largest wall bending moment after the first dig (2 m), 3-D twin vs 2-D k11-3d-wall-twin-dig1-moment · Self-check | 16.96kNm/m | 17.04kNm/m | −0.46 % | Ours 16.96 kNm/mPublished 17.04 kNm/m−0.46 % | Pass | |
| ||||||
largest wall bending moment after the second dig (4 m, strut at 1 m), 3-D twin vs 2-D k11-3d-wall-twin-dig2-moment · Self-check | 20.94kNm/m | 20.78kNm/m | +0.80 % | Ours 20.94 kNm/mPublished 20.78 kNm/m+0.80 % | Pass | |
| ||||||
strut force after the second dig, 3-D twin vs 2-D (no prestress: the 2-D and 3-D prestress conventions differ) k11-3d-wall-twin-dig2-strut · Self-check | 14.34kN/m | 14.18kN/m | +1.07 % | Ours 14.34 kN/mPublished 14.18 kN/m+1.07 % | Pass | |
| ||||||
top settlement of a laterally confined column after the water level is lowered from −2 m to −6 m (levels on node lines) k11-3d-water-drawdown-oedometer | 12.48mm | 12.48mm | 0.00 % | Ours 12.48 mmPublished 12.48 mm0.00 % | Pass | |
| ||||||
top settlement after a drawdown from −2 m to −5.25 m (the new level BETWEEN node lines: the wet part of the cut elements is clipped exactly) k11-3d-water-drawdown-cut-level | 10.7737mm | 10.7737mm | +7.7e-7 % | Ours 10.7737 mmPublished 10.7737 mm+7.7e-7 % | Pass | |
| ||||||
largest displacement of a K0 root with water (level −3 m) and of a plastic child that changes nothing k11-3d-water-k0-equilibrium | 0m | 0m | — | Ours 0 mPublished 0 m— | Pass | |
| ||||||
wall-top horizontal displacement after the second dig with the pit dewatered to −4 m (water −3 m behind the wall), 3-D twin vs 2-D k11-3d-wall-twin-water-dig2-top-ux · Self-check | -0.458mm | -0.465mm | −1.55 % | Ours -0.458 mmPublished -0.465 mm−1.55 % | Pass | |
| ||||||
largest wall bending moment after the second dig with the pit dewatered to −4 m, 3-D twin vs 2-D k11-3d-wall-twin-water-dig2-moment · Self-check | 36.38kNm/m | 36.14kNm/m | +0.66 % | Ours 36.38 kNm/mPublished 36.14 kNm/m+0.66 % | Pass | |
| ||||||
strut force after the second dig with the pit dewatered to −4 m, 3-D twin vs 2-D k11-3d-wall-twin-water-dig2-strut · Self-check | 21.88kN/m | 21.72kN/m | +0.72 % | Ours 21.88 kN/mPublished 21.72 kN/m+0.72 % | Pass | |
| ||||||
largest horizontal wall movement after the first dig, wall with interfaces (R_inter 0.67), 3-D twin vs 2-D k11-3d-wall-twin-iface-dig1-wall-ux · Self-check | 2.888mm | 2.875mm | +0.45 % | Ours 2.888 mmPublished 2.875 mm+0.45 % | Pass | |
| ||||||
largest horizontal wall movement after the second dig, wall with interfaces, 3-D twin vs 2-D k11-3d-wall-twin-iface-dig2-wall-ux · Self-check | 5.22mm | 5.21mm | +0.19 % | Ours 5.22 mmPublished 5.21 mm+0.19 % | Pass | |
| ||||||
largest wall bending moment after the second dig, wall with interfaces, 3-D twin vs 2-D k11-3d-wall-twin-iface-dig2-moment · Self-check | 27.06kNm/m | 27.26kNm/m | −0.74 % | Ours 27.06 kNm/mPublished 27.26 kNm/m−0.74 % | Pass | |
| ||||||
strut force after the second dig, wall with interfaces, 3-D twin vs 2-D k11-3d-wall-twin-iface-dig2-strut · Self-check | 17.05kN/m | 17.06kN/m | −0.05 % | Ours 17.05 kN/mPublished 17.06 kN/m−0.05 % | Pass | |
| ||||||
Cited validation suites
fe-consolidation-3d-web-validationWeb-benchmark validation for the 3-D COUPLED CONSOLIDATION FE (`fe-consolidation-3d.ts`).28 passing
Analyses validated: consolidation-3d
- Pass[1..16] Newmark corner influence factor reproduces Das (2016) Table 6.4
- Pass[17] Newmark I → 1/4 as m,n → ∞ (the whole surface loaded, four quadrants make q)
- Pass[18] Δσ_z under the centre: = q at the surface, and 4·I(m=n=1)·q at z = B/2
- Pass[19] confined final settlement = q·H/E_oed exactly, for every ν and every mesh
- Pass[20] VOLUMETRIC LOCKING: confined settlement stays exact as ν → ½
- Pass[21] confined undrained settlement is EXACTLY zero on any mesh
- Pass[22] Terzaghi's initial condition: confined initial excess pore pressure = q exactly
- Pass[23] E_oed and c_v = k·E_oed/γ_w follow the closed forms
- Pass[24] the loaded-area resultant is exact (consistent traction on a graded mesh)
- Pass[25] terzaghiU / terzaghiTv reproduce the published U–Tv table
- Pass[26] the confined solve follows the Terzaghi U(Tv) curve
- Pass[27] the confined solve reproduces the Terzaghi t50 and t90
- Pass[28] confined U increases monotonically and the excess pore pressure decays away
- Pass[28b] the peak excess pore pressure never exceeds the load, and converges to it
- Pass[29] double drainage divides t50 by four (the drainage path is halved)
- Pass[30] settlement is linear in the applied pressure, and t50 is independent of it
- Pass[31] settlement ∝ 1/E, and c_v ∝ E so t50 ∝ 1/E
- Pass[32] t50 ∝ 1/k with the settlement unchanged
- Pass[33] geometric similarity: doubling every length doubles s and quadruples t50
- Pass[34] a finite footprint consolidates FASTER than 1-D, increasingly so with H/B
- Pass[35] the Skempton-Bjerrum μ is below 1 and falls with H/B (Das Fig 7.22 trend)
- Pass[36] the confined limit is recovered continuously as the footprint widens
- Pass[37] the undrained instant equals a drained solve at ν → ½ with the same shear modulus
- Pass[38] the mixed undrained settlement is mesh-converged
- Pass[39] the Q2–Q1 pair is inf-sup stable on every mesh the engine will build
- Pass[40] every reported number is finite — no NaN or Infinity anywhere
- Pass[41] invalid input is rejected with a message, never with a plausible-looking number
- Pass[42] the config wrapper exposes days, a verdict and the 1-D comparison
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-footing-3d-web-validationValidation for the 3-D elasto-plastic continuum footing FE (`fe-footing-3d.ts`) — the closed-form cross-check (Vesić 1973 factors + Skempton/Meyerhof shape factors) that anchors the 3-D BVP and its shape effect.5 passing
Analyses validated: footing-bearing-3d
- PassVesić (1973) bearing-capacity factors (3-D engine) — published table (13 anchors)
- PassSkempton (1951): square/circular footing φ=0 shape factor s_c = 1.2 (N_c·s_c ≈ 6.2)
- PassMeyerhof/Vesić shape factors s_q, s_γ (square, φ=30°)
- Passshape factors interpolate B/L: strip → 1, square = max, rectangle between
- Pass3-D shape effect: a square footing carries more than the strip (the reason for a 3-D solve)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
fe-slope-3d-web-validationWeb-benchmark validation for `fe-slope-3d` — 3-D FE strength-reduction slope stability (20-node hex, viscoplastic Mohr-Coulomb).9 passing
Analyses validated: fe-slope-3d
- Passa 2:1 slope solves and reports a physical FoS with its mesh size
- Passthe 3-D FoS is at least the plane-strain FoS (Cavounidis 1987)
- Passthe 3-D strengthening effect decreases as the slope widens (Griffiths & Marquez 2007)
- PassFoS rises with cohesion and with friction angle
- PassFoS falls with height, with unit weight, and with a steeper slope
- Passthe stability number c/(γH) governs — geometrically similar slopes agree
- Passa slope at collapse is reported as unstable rather than left to look converged
- Passa caller-supplied time budget cannot truncate the search: the legacy keys change nothing (D426)
- Passinvalid geometry and strength are refused with NaN, not a plausible FoS
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
footing-3d-web-validationrecords a differenceC.FOOT3D — `footing-bearing-3d` web-benchmark (46 cited published values).9 passing
Analyses validated: footing-bearing-3d
- PassC.FOOT3D.1: 30 published Vesić bearing-capacity factors within 0.5%
- PassC.FOOT3D.2: N_c = 2+π = 5.14 and N_γ = 0 at φ = 0 (Prandtl 1920)
- PassC.FOOT3D.3: 12 published Vesić shape factors, square footing (B/L = 1)
- PassC.FOOT3D.4: closed-form q_ult matches 4 hand-worked Vesić totals within 0.5%
- PassC.FOOT3D.4b: solveFooting3D reports the SAME closed form it assembles internally
- PassC.FOOT3D.5: φ=0 square footing reproduces the Skempton N_c ≈ 6.2 form
- PassC.FOOT3D.6: φ = 0 clay square — the FE limit load obeys physical bounds and its D509 lock (always run)
- SkippedC.FOOT3D.6h: c-φ square with γ and D_f — physical bounds and its D509 lock (HEAVY tier)Not asserted: GEOTECH_HEAVY=1 (minutes in TS; the Python twin runs it in validate_fe_footing_3d.py)
- PassC.FOOT3D.7: monotonic in strength — more c, φ, γ or D_f cannot lower q_ult
- PassC.FOOT3D.8: mesh sizing is pinned (guards the P0-1 rounding tie)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pile-group-3d-web-validationrecords a differenceRigid-cap pile-group load distribution (`pile-group-3d.ts`) checked against PUBLISHED worked examples.14 passing
Analyses validated: pile-group-3d
- Pass[1] Mittal Ex 6.4: vertical term P/n = 201/4 = 50.3 t
- Pass[2] Mittal Ex 6.4: moment term for M = 4.8 t·m is 1.8 t
- Pass[3] Mittal Ex 6.4: moment term for M = 6.4 t·m (other axis) is 2.4 t
- Pass[4] Mittal Ex 6.4: moment term for M = 37.2 t·m (VL + EQ at 45°) is 13.8 t
- Pass[5] Mittal Ex 6.4: moment term for M = 46.9 t·m (VL + EQ at 67.5°) is 17.4 t
- Pass[6] Mittal Ex 6.4 case (i): P = 201, M₄₅ = 4.8, M₆₇.₅ = 6.4 → maximum pile load 54.5 t
- Pass[7] Mittal Ex 6.4 case (ii): P = 201, M₄₅ = 37.2, M₆₇.₅ = 6.4 → maximum pile load 66.5 t
- Pass[8] Mittal Ex 6.4 case (iii): P = 201, M₄₅ = 4.8, M₆₇.₅ = 46.9 → maximum pile load 69.5 t
- Pass[9] Mittal Ex 6.4 case (ii): earthquake shear 12.4 t over 4 piles is 3.1 t per pile
- Pass[10] Mittal Ex 6.5: vertical term 895/20 = 44.8 t
- Pass[11] Mittal Ex 6.5: moment term for M₂₅ = 69.6 t·m is 2.6 t
- Pass[12] Mittal Ex 6.5: moment term for M₉₀ = 42.9 t·m is 1.9 t
- Pass[13] Mittal Ex 6.5 case (i): P = 895, M₂₅ = 69.6, M₉₀ = 42.9 → maximum pile load 49.3 t
- Pass[14] Mittal Ex 6.5 case (ii): earthquake shear 12.0 t over 20 piles is 0.6 t per pile
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-3d-dem-web-validationWEB-BENCHMARK validation for the arbitrary-DEM 3-D slope engine (Scoops3D reimplementation).22 passing
Analyses validated: slope-3d-dem
- Passdem 1: a planar-slope DEM produces a converged critical sphere
- Passdem 2: DEM Bishop-3D MATCHES the validated 2-D engine (F₂D ≤ F₃D ≤ ~1.4·F₂D)
- Passdem 3: Ordinary-3D ≤ Bishop-3D (Fellenius conservative)
- Passdem 4: the failure mass has a real volume, area and column count
- Passdem 5: the auto fall direction points down-slope (−x for a slope rising in +x)
- Passdem 6: more cohesion ⇒ higher FoS
- Passdem 7: higher friction angle ⇒ higher FoS
- Passdem 8: a steeper slope ⇒ lower FoS
- Passdem 9: a taller slope ⇒ lower FoS
- Passdem 10: a high water table ⇒ lower FoS than dry
- Passdem 11: ru pore-pressure ratio lowers FoS
- Passdem 12: a weak lower layer lowers FoS vs uniform strong soil
- Passdem 13: two-material honoured — heavier soil (more driving) ⇒ ≤ FoS of lighter
- Passdem 14: a finer search evaluates more spheres and returns a sensible minimum ≥ F₂D
- Passdem 15: method=ordinary headlines the Ordinary FoS
- Passdem 16: an explicit slip direction is honoured
- Passdem 17: a tiny/invalid DEM errors cleanly (no crash)
- Passdem 18: missing materials errors cleanly
- Passdem 19: a nearly-flat DEM is very stable (high FoS)
- Passdem 20: bilinear DEM interpolation — result is stable to a half-cell origin shift
- PassDEM E-116: an INVERTED material band must be rejected, not read as the deepest one
- PassDEM E-116: non-finite and non-physical material properties must be named, not blamed on the DEM
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
slope-3d-web-validationWEB-BENCHMARK validation for the 3-D slope-stability engine — now the GENUINE Hungr (1987) 3-D simplified-Bishop COLUMN method on an ellipsoidal slip surface (vertical-column grid, true 3-D base normal n_y, per-column moment arm R_z), not…34 passing
Analyses validated: slope-stability
- Passslope3d 1: Zhang (1988) ellipsoid F₃D in the published band 2.12–2.26
- Passslope3d 2: Zhang F₃D/F₂D sits in the rotational band and exceeds 1 (Cavounidis)
- Passslope3d 3: F₃D ≥ F₂D — c–φ soil (Cavounidis 1987 theorem)
- Passslope3d 4: F₃D ≥ F₂D — purely cohesive (φ=0) soil
- Passslope3d 5: F₃D ≥ F₂D — nearly cohesionless (c=5, φ=35) soil
- Passslope3d 6: on the symmetry plane the column method reduces to 2-D Bishop (F₂D exact)
- Passslope3d 6b: ru pore-pressure lowers F₃D (Bishop-3D (W − u·A_h) effective-stress term)
- Passslope3d 7: F₂D cross-checks our rigorous Spencer FoS (independent kernel)
- Passslope3d 8: cohesive (φ=0) shows a LARGER 3-D effect than frictional (Stark & Eid 1998)
- Passslope3d 9: F₃D/F₂D within the Duncan (1996) rotational band 1.03–1.55 (typical geometry)
- Passslope3d 10: narrower slide ⇒ stronger (higher F₃D/F₂D)
- Passslope3d 11: the F₃D/F₂D-vs-aspect curve is monotone decreasing
- Passslope3d 12: PURE-ELLIPSOID limit — very long slide ⇒ ratio plateaus > 1 (NOT → 1)
- Passslope3d 13: φ=0 near-spherical slide (aspect≈1) has a strong 3-D effect (ratio > 1.15)
- Passslope3d 14: more cohesion ⇒ higher F₂D and F₃D
- Passslope3d 15: steeper slope ⇒ lower F₃D
- Passslope3d 16: a high water table ⇒ lower F₃D (effective-stress reduction)
- Passslope3d 17: verdict PASS when F₃D ≥ required, FAIL when below
- Passslope3d 18: verdict headlines both F₂D and F₃D + the % insight
- Passslope3d 19: translational mode flags the model + names Hungr conservative default
- Passslope3d 20: invalid slide length ⇒ errors, no crash
- Passslope3d 21: converged flag set + a real column grid was built
- Passslope3d 22: reports critical-circle radius and z semi-axis (=L/2)
- Passslope3d 23: ru pore-pressure ratio lowers F₃D vs drained
- Passslope3d 24: refining the column grid changes F₃D by < 2 % (numerical convergence)
- Passslope3d 25: the 3-D search finds a critical F₃D ≤ the extruded 2-D-circle F₃D
- Passslope3d 26: the searched critical F₃D still satisfies Cavounidis F₃D ≥ F₂D
- Passslope3d 27: search is on by default and reports how many surfaces it scanned
- Passslope3d 28: search lowers (or holds) the Zhang F₃D toward the published 2.12–2.26
- Passslope3d 29: reports Ordinary, Bishop, rigorous Spencer AND GLE 3-D side-by-side
- Passslope3d 30: Ordinary ≤ Bishop and rigorous Spencer within 2 % of Bishop (all soils)
- Passslope3d 31: rigorous Spencer-3D agrees with Bishop-3D within ~10 % (Hungr 1987; Lam-Fredlund 1993)
- Passslope3d 32: selecting method=spencer makes the headline F₃D the Spencer value
- Passslope3d 33: each 3-D method reduces to its 2-D counterpart at the prismatic limit
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
tet-mesh-3d-web-validationValidation for the TerraCore 3-D tetrahedral mesher (`tet-mesh-3d.ts`).18 passing
Analyses validated: tet-mesh-3d
- Passreference tet volume is 1/6
- Passcircumsphere of the reference tet centres at (½,½,½), R=√3/2
- Passregular tetrahedron: quality ρ=1 and dihedral 70.5288°
- Passstructured 1×1×1 box → 6·n³ = 6 tets, (n+1)³ = 8 nodes
- Passstructured 2×2×2 box → 6·n³ = 48 tets, (n+1)³ = 27 nodes
- Passstructured 3×3×3 box → 6·n³ = 162 tets, (n+1)³ = 64 nodes
- Passstructured 4×4×4 box → 6·n³ = 384 tets, (n+1)³ = 125 nodes
- Passbox 3×2×4 m, 3×3×3 cells: volume, Euler, positivity, conformity, quality
- Passextruded rectangle 5×3 through depth 2, 4 layers: Σ vol = 30, conforming, Euler
- Passextruded triangle (legs 4,6) through depth 5: Σ vol = ½·4·6·5 = 60
- Passextruded L-shape polygon: Σ vol = plan_area·depth, conforming
- PassDelaunay empty-circumsphere property holds (random 3-D set, seed 1)
- PassDelaunay empty-circumsphere property holds (random 3-D set, seed 7)
- PassDelaunay empty-circumsphere property holds (random 3-D set, seed 42)
- PassDelaunay of 8 unit-cube corners tiles volume 1 and is Delaunay after restriction
- Passboundary point-cloud path: convex hull volume, Delaunay, positive, dihedral>0
- Passradius-ratio quality is invariant under uniform scaling
- Passdegenerate box (zero height) returns an error, not NaN
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Pavements and airfields
0 finite-element rows · 2 closed-form problems · 62 validation suites
Closed-form engine registry
| Problem | Ours | Published | Difference | Tolerance | Status | Details | |
|---|---|---|---|---|---|---|---|
IRC:37 Annex I Fig I.3 — εt at the bottom of the bituminous layer, dual-wheel standard axle D1-IRC37-DUAL-WHEEL | 128.481µε | 128.3µε | +0.14 % | ± 2 % | Ours 128.481 µεPublished 128.3 µε+0.14 % | Pass | |
| |||||||
IRC:37 Annex I Fig I.3 — εv on top of the subgrade, dual-wheel standard axle D1-IRC37-DUAL-WHEEL-EV | 205.59µε | 205.3µε | +0.14 % | ± 2 % | Ours 205.59 µεPublished 205.3 µε+0.14 % | Pass | |
| |||||||
Cited validation suites
aashto-rigid-1993-web-validationrecords a differenceAASHTO 1993 RIGID (PCC slab) PAVEMENT — Eq.11 passing
Analyses validated: aashto-rigid-1993, pavement-aashto-1993
- PassAppendix I §1.1 — first-year design-lane traffic 357,000 × 0.80 × 0.50 = 142,800 and the per-stage reliabilities
- PassAppendix I §1.2 — slab thickness 9 in for the 25-year traffic (Figure 3.7, no swelling)
- PassAppendix I Table I.3 — a 9 in slab carries 4.6×10⁶ ESALs at ΔPSI_TR 1.75 (iteration 1) and 4.5×10⁶ at 1.74 (iteration 2)
- PassAppendix I Table I.3 — those capacities correspond to 22.9 and 22.8 years on the Figure I.1 traffic curve
- PassAppendix I §1.2 Step 7 — the design "will reach its terminal serviceability in approximately 23 years"
- PassFHWA §6.2.1 baseline rigid design — k_eff 38 pci → D = 10.4 in (10.5 in after rounding)
- PassFHWA §6.3.1 soft subgrade — k_eff 27 pci → D = 10.5 in, and the baseline slab then carries 15.5×10⁶ ESALs
- PassFHWA §6.5.1 low-quality subbase — k_eff 17 pci, Cd 0.85 → D = 11.5 in, baseline slab carries 8.3×10⁶ ESALs
- PassFHWA §6.6.1 poor drainage — k_eff 12 pci, Cd 0.75 → D = 12.3 in, baseline slab carries 5.2×10⁶ ESALs
- PassFHWA §6.2.1 — the 10.4 in baseline slab at k 38 pci carries the 16.4×10⁶ ESALs it was designed for
- PassAASHTO Table 4.1 — Z_R for every tabulated reliability, as reported by the rigid design engine
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
acn-pcn-airfield-published-web-validationPUBLISHED-VALUES: 15 -- distinct published values for this engine (engine-level total, declared once); independent audit A1: about 15 published values, 6 of them from a source the auditor could not reach.5 passing
Analyses validated: acn-pcn-airfield
- PassICAO Doc 9157 Part 3 Ch.2 (via Hayhoe 2010): 10 % flexible and 5 % rigid occasional-overload limits
- PassBoeing ACAP §7.10 / ICAO: ACN ≤ PCN operates without restriction (ratio ≤ 1)
- PassHayhoe (2010) Eq. 5: ACN/PCN = (t2/t1)², so √ratio reproduces the printed thickness ratios 1.049 and 1.0247
- PassBoeing ACAP §7.10 ACN table (737 family at maximum taxi weight) against the published overload rule — expected status HAND-DERIVED
- Passpublished ACNs sit inside the engine's plausibility window (ACAP 737 table: 13 … 63; warning only above 2000)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
acn-pcn-airfield-web-validationFormula-fidelity validation against ICAO Annex 14 Vol I §2.6, ICAO Doc 9157 Part 3, and FAA AC 150/5335-5 — the ACN/PCN aircraft-pavement strength compatibility check and its published occasional-overload limits (10% for flexible pavements…9 passing
Analyses validated: acn-pcn-airfield
- Pass[1-3] ACN 45 / PCN 50 (ratio 0.90, flexible): unrestricted, overload=0%, limit=10%
- Pass[4-6] ACN 55 / PCN 50 (ratio 1.10, flexible): exactly at the 10% occasional limit -> permitted
- Pass[7-9] ACN 55 / PCN 50 (ratio 1.10, RIGID): exceeds the 5% rigid limit -> not permitted
- Pass[10-11] ACN 60 / PCN 50 (ratio 1.20, flexible): 20% overload exceeds the 10% limit
- Pass[12] rigid vs flexible use different overload limits at otherwise identical inputs
- Pass[13] ACN=PCN exactly (ratio=1.0) is unrestricted with zero overload
- Pass[14] default pavement type (unspecified) is treated as flexible (10% limit)
- Pass[15] ACN or PCN <= 0 is refused, not silently floored to a denominator of 1e-6
- Pass[16] the ratio is scale-invariant (ACN/PCN unaffected by proportional scaling), but implausible raw magnitudes still warn
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
aircraft-gear-response-web-validationPublished-value validation of the multi-wheel landing-gear response engine `aircraft-gear-response` (Burmister layered-elastic superposition over the wheels of a gear, maximum vertical strain at the top of the subgrade), against the FAARFI…2 passing
Analyses validated: aircraft-gear-response, layered-elastic-pavement
- Passmaximum subgrade strain of the 2D (4-wheel) and 6-wheel 3D gears reproduces TC-17/28 Appendix B (µε)
- Passwrapper outputs: contact radius from the Appendix A wheel load / tyre pressure, and the single-wheel identity
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
aircraft-library-web-validationWeb-benchmark validation for the airfield aircraft library — pins every gear-geometry value to the FAARFIELD standard-library / ACAP baselines that a PE (or FAARFIELD itself) would use, so our airfield engines run on the SAME aircraft inpu…9 passing
Analyses validated: faarfield-mix-cdf
- PassB747-8 gear geometry matches the FAARFIELD/ACAP baseline
- PassA320-200 gear geometry matches the FAARFIELD/ACAP baseline
- PassA330-300 gear geometry matches the FAARFIELD/ACAP baseline
- PassB737-800 is a dual-gear narrowbody (FAARFIELD standard library)
- Passwheel load = gross · %-on-leg / wheels-per-leg (at max taxi weight)
- Passa heavy widebody mix produces a higher subgrade CDF than a narrowbody mix
- Passpicking a1_aircraft/a2_aircraft reproduces the manual-geometry result exactly
- Passpicking overrides deliberately-wrong manual fields (geometry comes from the library)
- Passthe library covers the 4 Appendix-H benchmark aircraft with valid specs
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
asphalt-institute-design-published-web-validationASPHALT INSTITUTE FATIGUE / SUBGRADE-RUTTING CRITERIA — `asphaltInstituteFatigueLife` and `asphaltInstituteRuttingLife` (the two functions `computeAsphaltInstituteDesign` applies to the layered-elastic strains) checked against PUBLISHED ST…6 passing
Analyses validated: asphalt-institute-design
- PassMaher (2022) KENLAYER — fatigue: five printed tensile strains → allowable repetitions (E₁ = 500 000 psi)
- PassMaher (2022) KENLAYER — subgrade rutting: five printed compressive strains → allowable repetitions
- PassMaher (2022) — the hand calculation in the notes: εt 1.423E-04 → 4,940,000 and the differential 6.63E-05 → 60,890,000
- PassMaher (2022) — Miner summation of the printed strains reproduces the summary: ΣD 3.946E-02 (fatigue), 5.174E-02 (rutting), 19.33 years
- PassRahmawati & Adiyasa (2021) Table 3 — εt 2.998E-04 with E = 1 200 000 kPa gives Nf = 1,047,484.63; εc 4.022E-04 gives Nd = 2,172,928.92
- PassRahmawati & Adiyasa (2021) Table 5 — two alternative designs: Nd at εc 1.979E-04 and 1.912E-04, and the Nf ratio of εt 9.501E-05 to 9.331E-05
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
asphalt-institute-design-web-validationFormula-fidelity validation against Asphalt Institute MS-1 "Thickness Design" (1981/1999) and Huang, "Pavement Analysis and Design" 2nd ed.7 passing
Analyses validated: asphalt-institute-design
- Pass[1-6] base case: Nf and Nr independently re-derived from the engine's own reported strains match its output exactly (formula fidelity of the AI transfer functions)
- Pass[7] the specific reference case cited in the engine's own defect-fix comment reproduces exactly: Nf ~= 1.987e6, governing = subgrade rutting, CDF ~= 1.35
- Pass[8] doubling the AC modulus reduces the fatigue allowable Nf by exactly 2^0.854 per the published -0.854 exponent, at fixed strain
- Pass[9] design_esals=0 gives exactly zero damage ratios, labelled as definitional
- Pass[10] a thicker/stiffer section reduces both strains and both damage ratios (basic M-E design trend)
- Pass[11] the classification bands match the CDF thresholds (<=0.5 ample, <=1.0 within limit, >1.0 inadequate)
- Pass[12] every load-bearing input is refused at 0 or below, never silently floored to an unbounded allowable
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
axle-load-spectra-published-web-validationPublished-value checks for the axle-load spectrum → equivalent-axle engine `axle-load-spectra` (fourth-power load-equivalency law per axle group, truck factor, wander factor).3 passing
Analyses validated: axle-load-spectra
- PassIRC:37-2018 Eq. 4.2: a single axle with dual wheels is equivalent to (load / 80)^4 standard axles
- PassIRC:37-2018 Annex II.2 dumper: 2×(120/80)^4 + (80/65)^4 = 12.41, × 200 repetitions = 2483 standard axles
- PassIRC:37-2018 Eq. 4.2 fixes the 80 kN standard the engine uses for the single-axle group
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
axle-load-spectra-web-validationFormula-fidelity validation against AASHTO Guide for Design of Pavement Structures (1993) App.10 passing
Analyses validated: axle-load-spectra
- Pass[1-6] single-axle group, fourth-power law: truck factor=1.8488, ESALs=1848828.1, mean=82.0kN, %above-std=35.0%
- Pass[7-12] per-bin LEF values match (P/Pstd)^4 exactly for each of the six bins
- Pass[13] tandem group uses the 140 kN standard load, not 80 kN
- Pass[14] tridem group uses the 210 kN standard load
- Pass[15] a custom power exponent (n=3.9) changes every LEF and the resulting ESALs, per the fourth-power law generalisation
- Pass[16-18] traffic wander factor: MEPDG default (tire=300mm, sigma=254mm) = 0.445179; channelised (sigma=0) = 1; narrow wander (sigma=50mm) = 0.997300
- Pass[19] design ESALs at the critical point equals raw ESALs times the wander factor (within the engine's own rounding of each intermediate to a fixed number of decimals)
- Pass[20] total_axles=0 gives exactly zero ESALs, labelled as definitional rather than a low-damage spectrum
- Pass[21] spectrum percentages that do not sum to 100 are normalised internally and warned about
- Pass[22] empty spectrum or negative total axles are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
benkelman-overlay-published-web-validationrecords a differenceBENKELMAN-BEAM OVERLAY DESIGN — `computeBenkelmanOverlay` (IRC:81-1997 characteristic deflection, with the §4.4.3 temperature and §4.5.4 seasonal corrections) checked against PUBLISHED WORKED EXAMPLES.7 passing
Analyses validated: benkelman-overlay
- PassIRC:81-1997 §4.4.3 — at 37 °C the correction is 0.02 mm and is subtracted
- PassCSIR-CRRI slides — 0.80 mm measured at 37 °C → 0.78 mm, and at 32 °C → 0.83 mm at the 35 °C standard
- PassUnattributed (2020) IRC overlay-design slides — 0.8 mm at 38 °C → 0.8 − 3 × 0.01 = 0.77 mm
- PassUnattributed (2020) IRC overlay-design slides — eleven readings have mean deflection 0.95 mm
- Pass4-BBD slides — uncorrected statistics: mean 1.45 mm, standard deviation 0.107 mm, Dc = 1.45 + 2(0.107) = 1.664 mm
- Pass4-BBD slides — temperature correction 0.01 × (35 − 30) = +0.05 mm gives Dc = 1.714 mm
- Pass4-BBD slides — seasonal factor 1.4 gives the corrected characteristic deflection 2.3996 mm
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
benkelman-overlay-web-validationrecords a differenceFormula-fidelity validation against IRC 81:1997 Cl 6 (characteristic deflection Dc = mean + k.sigma, k=2 major roads Eq.4 / k=1 minor roads Eq.5) and Cl 5.4/5.5 (temperature/seasonal correction factors).8 passing
Analyses validated: benkelman-overlay
- Pass[1-5] major road (k=2, Eq.4), corrected by CT=1.05, CS=1.02: mean=1.371951mm, sd=0.117154mm, Dc=1.606258mm, overlay required, reduction=0.106258mm
- Pass[6-7] minor road (k=1, Eq.5), same data and allowable: Dc=1.489105mm, no overlay required
- Pass[8] no allowable supplied -> overlay_required is null (NOT ASSESSED), never false
- Pass[9] a generous allowable above Dc gives overlay_required=false with zero reduction
- Pass[10] a non-positive allowable is refused outright, not silently treated as "no overlay needed"
- Pass[11] correction factors default to 1.0 when not supplied, so mean/Dc equal the uncorrected statistics
- Pass[12] fewer than 10 readings warns about IRC 81-1997 Cl 4.3.1's minimum sample size
- Pass[13] no readings, or a negative reading, is refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
climate-zone-eicm-web-validationPUBLISHED-VALUES: 8 -- distinct published values for this engine (engine-level total, declared once); independent audit A1: eight Koppen-Geiger / Peel threshold values and no published numeric answer for the engine.33 passing
Analyses validated: climate-zone-eicm
- Passevery zone the engine offers is one of the six Koppen-labelled zones and returns 12 monthly temperatures
- Passtropical: Peel 2007 Table 1 "A": Tcold >= 18 degC (coldest monthly mean)
- Passtropical: Kottek 2006 Table 1 "A": Tmin >= +18 degC
- Passtropical: Af rainforest needs Pmin >= 60 mm in EVERY month (Peel/Kottek) => MAP >= 12 x 60 = 720 mm; engine 2000 mm
- Passtropical: not arid - Peel "B": MAP < 10 Pthreshold must FAIL; the largest Pthreshold (summer-dominant rain) is 2 MAT + 28
- Passtropical: a frost-free climate has no sub-zero month, so its freezing index must be 0 (consequence of Tcold >= 18)
- Passarid_hot: Peel "BW": MAP < 5 Pthreshold holds under the SMALLEST Pthreshold (winter-dominant rain, 2 MAT)
- Passarid_hot: Kottek "BW": Pann <= 5 Pth under the same smallest Pth
- Passarid_hot: Peel "h" (hot): MAT >= 18 degC
- Passarid_hot: the mean of the 12 monthly temperatures reproduces the stated MAT (the Koppen MAT the "h" test is applied to)
- Passarid_hot: not polar - Peel/Kottek "E" needs Thot < 10; the hottest month is well above it
- Passarid_hot: a frost-free desert (coldest month >= 18) has freezing index 0
- Passtemperate: Peel "C": Thot > 10 and 0 < Tcold < 18
- Passtemperate: Kottek "C": -3 < Tmin < +18 degC
- Passtemperate: not arid - Peel "B" fails: MAP >= 10 x the LARGEST Pthreshold (2 MAT + 28)
- Passtemperate: Peel "a" (hot summer) Thot >= 22, so Cfa is the right third letter; Kottek "a" Tmax >= +22 agrees
- Passtemperate: a zone whose coldest month is above 0 degC can still carry a small frost index (daily extremes), but never a negative one
- Passcontinental_cold: Peel "D": Thot > 10 and Tcold <= 0
- Passcontinental_cold: Kottek "D": Tmin <= -3 degC (the stricter Koppen boundary)
- Passcontinental_cold: Peel "b" (warm summer): NOT "a" (Thot < 22) and Tmon10 >= 4; Kottek "b": at least 4 months >= +10
- Passcontinental_cold: not arid - MAP >= 10 x the largest Pthreshold (2 MAT + 28)
- Passcontinental_cold: a climate with Tcold <= -3 must have freezing weather, so FI > 0
- Passsubarctic: Peel "D": Thot > 10 and Tcold <= 0
- Passsubarctic: Kottek "D": Tmin <= -3 degC
- Passsubarctic: Peel "c" (cold summer): NOT a, b or d. Not "a" (Thot < 22) and not "b" (Tmon10 < 4) - i.e. 1 <= Tmon10 < 4
- Passsubarctic: not "d" (very cold winter): Peel needs Tcold < -38; Kottek "d" Tmin <= -38. The engine is far warmer
- Passsubarctic: not arid - MAP >= 10 x the largest Pthreshold (2 MAT + 28, with MAT = -2)
- Passsubarctic: Tcold <= -3 again implies freezing weather, so FI > 0
- Passmediterranean: Peel "C": Thot > 10 and 0 < Tcold < 18
- Passmediterranean: Kottek "C": -3 < Tmin < +18 degC
- Passmediterranean: Peel "a" (hot summer, the "a" of Csa): Thot >= 22; Kottek "a" Tmax >= +22
- Passmediterranean: not arid - a dry-summer climate has winter-dominant rain, so Pthreshold is 2 MAT or 2 MAT + 14; MAP >= 10 x the larger
- Passsouthern hemisphere: Tcold, Thot and Tmon10 are unchanged by the phase flip, so every class test above still holds
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
crcp-punchout-published-web-validationCRCP punchout (MEPDG 2nd ed.8 passing
Analyses validated: crcp-punchout
- PassTable 9-9 Interstate "Adequate < 5 punchouts/lane-mi": just below 5 the engine says "below the typical 10/mi terminal"
- PassTable 9-9 Interstate "Marginal 5 to 10": just above 5 the engine leaves the "below" band and says "approaching the terminal"
- PassTable 9-9 / Sakulneya 2024: just below the 10 punchouts/mi terminal the engine still says "approaching"
- PassTable 9-9 Interstate "Inadequate > 10" and Sakulneya 2024 "<= 10": just above 10 the engine says "exceeds the typical terminal"
- PassEq. 5-26 upper asymptote APO = 216.8421 /mi: at the engine's largest damage (1e9) PO is within 0.05 % of the printed APO and never above it
- PassEq. 5-26 is monotone increasing in damage and stays below APO across six decades of DIPO
- PassNIST SP 811 App. B.8: 1 mi = 1.609344 km exactly, so punchouts/km = punchouts/mi / 1.609344
- PassTable i-1: the engine implements the 2nd-ed. (2015) constants, NOT the MEPDG v1.1 ones - at DI = 1 the two models differ by > 10 %
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
crcp-punchout-web-validationFormula-fidelity validation against AASHTO MEPDG "A Manual of Practice" 2nd ed.12 passing
Analyses validated: crcp-punchout
- Pass[1] DI=1 -> PO=6.348229 punchouts/mi (Eq. 5-26 exact)
- Pass[2] DI=5 -> PO=15.667781 punchouts/mi
- Pass[3] DI=10 -> PO=22.745760 punchouts/mi
- Pass[4] DI=20 -> PO=32.504608 punchouts/mi
- Pass[5] DI=50 -> PO=50.376631 punchouts/mi
- Pass[6] DI=100 -> PO=67.846404 punchouts/mi
- Pass[7] DI=500 -> PO=117.186387 punchouts/mi
- Pass[8] DI=1000 -> PO=138.542458 punchouts/mi
- Pass[9] DI=0 -> PO=0 exactly (definitional, guarded above Eq. 5-26 for the DI<=0 branch)
- Pass[10] km conversion is exact: PO/mi / 1.609344 = PO/km at DI=10
- Pass[11] monotone increasing in DI (fatigue damage), asymptotic toward APO=216.8421
- Pass[12] classification bands match the terminal thresholds used in the engine (below 5, 5-10, >10 punchouts/mi)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
dcp-web-validationrecords a difference`dcp` — anchored to ASTM D6951/D6951M − 09 (Reapproved 2015).12 passing
Analyses validated: dcp
- PassASTM D6951 expression (1): CBR = 292/DPI^1.12 for all soils but CL<10 and CH
- PassASTM D6951 expression (3): CL soils with CBR < 10 use CBR = 1/(0.017019·DPI)²
- PassASTM D6951 expression (5): CH soils use CBR = 1/(0.002871·DPI)
- Passthe mm/blow and in./blow coefficients differ by exactly 25.4 — proof of transcription
- PassASTM D6951 Table 2: all 64 tabulated CBR values reproduced within the table’s own rounding
- PassASTM D6951 Table 2: CBR is strictly decreasing across the table, and the ends match its caps
- Passend-to-end: a uniform profile returns the DCP index and CBR the standard predicts
- PassE-40: the 4.6 kg hammer factor is ASTM’s integer 2, not the 8/4.6 mass ratio
- Passa non-standard hammer mass is extrapolated BEYOND ASTM and says so
- Passend-to-end: a layered profile splits at the change of penetration rate
- Passthe alternative correlations are the published ones, and differ from ASTM as documented
- Passevery output is finite, and a refusal (zero penetration) is not reported as strong ground
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faa-airfield-thickness-published-web-validationSource-agreement checks for the closed-form airfield thickness engine `faa-airfield-thickness` (Corps/FAA CBR equation + Westergaard free-edge rigid design).4 passing
Analyses validated: faa-airfield-thickness
- Passrigid: radius of relative stiffness uses the printed constants E = 4,000,000 psi and ν = 0.15 (AC 6D para 337, AC 6G Table 3-2)
- Passrigid: the solved slab satisfies the edge-stress criterion σ_edge = R / DF with Mathew Eq. 15.4 and b from Eq. 15.2
- Passrigid: stress ∝ 1/h² dependence (Mathew Eq. 15.4) — a stronger concrete gives a thinner slab
- Passflexible: the Corps CBR form t = α·√(P/(8.1·CBR) − A/π) gives zero cover when the tyre footprint alone spreads the load
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faa-airfield-thickness-web-validationFormula-fidelity validation against FAA AC 150/5320-6D Ch.3 (flexible, U.S.9 passing
Analyses validated: faa-airfield-thickness
- Pass[1-3] flexible: P=30000lb, p=200psi, CBR=8%, C=25000 -> alpha=1.161526, t=23.668258in (601.174mm)
- Pass[4-6] flexible: heavier load, worse CBR: P=45000lb, p=220psi, CBR=6%, C=50000 -> alpha=1.230763, t=36.110201in
- Pass[7-10] rigid: P=30000lb, p=200psi, k=300pci, R=700psi, DF=1.3 -> h=10.032231in, sigma=allow=538.461538psi, l=32.730929in
- Pass[11] rigid: at the converged thickness, edge stress equals the allowable stress to within the bisection tolerance
- Pass[12] rigid: default design factor is 1.3 when not supplied
- Pass[13] flexible: a stronger subgrade (higher CBR) or lighter load reduces the required cover thickness
- Pass[14] flexible: coverages < 1 clamps to C=1 (alpha only defined for C>=1) and warns
- Pass[15] flexible: CBR, wheel load, or tire pressure at 0 or below is refused
- Pass[16] rigid: k, R, or DF at 0 or below is refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-ac-cdf-published-web-validationSource-agreement checks for the FAARFIELD HMA fatigue CDF engine `faarfield-ac-cdf` (RDEC plateau-value model: PV from strain / stiffness / volumetrics / gradation, then Nf from PV).2 passing
Analyses validated: faarfield-ac-cdf
- Passengine Nf(PV) is the inverse of the published Shen-Carpenter PV–Nf50 relation across stiffness and strain
- Passthe published relation is monotone the way the engine assumes: a larger plateau value means a shorter fatigue life
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-ac-cdf-web-validationFormula-fidelity validation against Carpenter & Shen (2006) "A Dissipated Energy Approach to Fatigue Evaluation," Road Mater.7 passing
Analyses validated: faarfield-ac-cdf
- Pass[1-2] volumetric parameter VP = Va/(Va+Vb) and gradation parameter GP = (PNMS-PPCS)/P200 match exactly for the base case
- Pass[3-6] PV, Nf, applied coverages, and CDF independently re-derived from the engine's own reported strain match its output exactly
- Pass[7] the specific reference case cited in the engine's own header reproduces the correct order of magnitude: et~250ue, S~3447MPa -> Nf order 1e6
- Pass[8] the PV exponent on strain (5.14) is exactly reproduced: doubling et raises PV by exactly 2^5.14
- Pass[9] a higher pass-to-coverage ratio (more wander) reduces applied coverages, and hence the CDF, proportionally
- Pass[10] annual_departures=0 gives zero applied coverages and zero CDF
- Pass[11] every load-bearing input is refused at 0 or below (never silently floored to an unbounded Nf)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-cdf-web-validationPublished-value validation of the single-aircraft FAARFIELD subgrade CDF engine `faarfield-cdf` (3-layer AC / base / subgrade Burmister response → FAA subgrade failure model → wander coverages).4 passing
Analyses validated: faarfield-cdf
- Passsubgrade failure model lies on the TC-17/28 Table 4 lower-envelope data (Bleasdale branch, C ≥ 1000)
- Passtangent point and the Table 6 linear branch (Eq. 6)
- Passwander and effective-width constants follow AC 6G §3.12.8.7 / §3.12.9.2
- Passengine chain: the reported coverages-to-failure is the published model at the reported strain (HAND-DERIVED identity)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-design-published-web-validationPublished-criterion validation of the FAARFIELD-class flexible THICKNESS design engine `faarfield-design` (iterates the asphalt thickness of a 3-layer AC / base / subgrade section until the Miner mix CDF = 1).4 passing
Analyses validated: faarfield-design
- PassAC 6G §3.12.9.1: the designed thickness has CDF = 1 for the traffic mix
- PassAC 6G §3.12.9.1 / TC-17/28 Eq. 7: the mix CDF is the sum of the per-aircraft terms
- PassAC 6G §3.12.2.3: a single "design aircraft" carrying all departures over-designs the true mix
- Passthe design thickness responds to the design-life input the way the CDF definition requires
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-design-web-validationEVIDENCE CLASS (added with the 2026-10 published-value audit): formula-fidelity / design-property evidence only.9 passing
Analyses validated: faarfield-design
- Pass[1-2] single aircraft: converges, and the design CDF is within the engine's own documented tolerance of the FAA design condition CDF=1.0
- Pass[3] the single aircraft's CDF contribution accounts for 100% of the total when it is the only aircraft in the fleet
- Pass[4-5] a two-aircraft mix's CDF contributions sum to the design CDF (Miner's cumulative damage rule) and each is a real fraction of it
- Pass[6] a two-aircraft mix requires MORE thickness than the single heaviest aircraft designed alone (the mix cannot be easier than its governing member)
- Pass[7] a heavier wheel load requires a thicker design section, all else equal
- Pass[8] more annual departures over the same design life requires a thicker section
- Pass[9] a stronger subgrade reduces the required thickness for the same fleet
- Pass[10] no aircraft in the fleet, or an aircraft with zero load/departures, is refused
- Pass[11] the returned required thickness lies within the search bracket [min, max]
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-flexible-published-web-validationPublished-value validation of the FAARFIELD flexible (LEAF) design engine `faarfield-flexible` (and the layered-elastic multi-wheel kernel it drives), against two independent FAA documents.10 passing
Analyses validated: faarfield-flexible
- Passmax subgrade strain of the NAPTF 4-wheel (2D) and 6-wheel (3D) gears reproduces TC-17/28 Appendix B
- PassEq. 1 reproduces TC-17/28 Table 1(b) sublayer moduli (4 × 6.0025 in P-154, 8 in P-209) to the psi
- Passthe Bleasdale curve (Eq. 4) lies on the Table 4 lower-envelope data it was regressed to
- Passthe tangent point (Eq. 6) and Table 6 unshifted FAARFIELD 1.41 coverages-to-failure
- PassTC-17/28 Table 2: B737-800, 1 200 dep/yr, 20 yr, 5 in P-401 + 8 in P-209 → P-154 t1 at CBR 3/6/10/15
- PassTC-17/28 Table 2: effective equivalency factor feq = t3/t2 (P-209 cut by 3 in → extra P-154)
- PassAC 6G Appendix H.2: 4 in P-401 / 8 in P-403 / 12 in P-209 / P-154 on CBR 5 → "10.1 inches P-154"
- PassAC 6G Appendix H.8: apron extension, same traffic, CBR 5, 6 in P-209 → "18 inches P-154" (36 in total)
- Passlayer inputs follow AC 6G Table 3-2 and the published subgrade modulus convention
- PassTable 3-3 minimum P-209 of 6 in applies from 60,000 lb, both weight classes
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-flexible-web-validationWeb-benchmark validation for the full FAARFIELD 1.41 flexible LEAF design.11 passing
Analyses validated: faarfield-cdf, faarfield-flexible
- PassgranularSublayers reproduces FAA-TC-17/28 Table 1 P-154 sublayer moduli (WES params)
- PassgranularSublayers reproduces FAA-TC-17/28 Table 1 P-209 modulus (WES params)
- PassFAAModulus sublayering keeps the top sublayer between base/2 and 1.5·base
- Passthe Bleasdale + tangent branches meet at exactly 1000 coverages
- PassBleasdale model tracks the FAA-TC-17/28 Table 4 points (≥ 1000 coverages)
- Passthe flexible engine and faarfield-cdf/mix-cdf share the SAME Bleasdale model
- Passthe linear tangent branch governs below 1000 coverages (Eq. 6)
- PassAppendix-H flexible design reproduces P-154 ≈ 10.1 in (to the inch)
- Passthe assembled section reports sane sublayer moduli + subgrade E = 1500·CBR
- Passdesign is monotone: a weaker subgrade needs a thicker P-154
- Passa P-209-only design honours the 6-in FAA minimum base thickness (Table 3-3)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-mix-cdf-web-validationPublished-value validation of the two-aircraft FAARFIELD subgrade CDF engine `faarfield-mix-cdf` (Miner sum over an aircraft mix, 82 strips, 3-layer AC / base / subgrade response).5 passing
Analyses validated: faarfield-mix-cdf
- Passthe B737-800 handed to the engine agrees with the Boeing ACAP (D6-58325-6 §7.2.4 / §7.10)
- PassAC 6G §3.12.9.1 / TC-17/28 Eq. 7: the mix CDF is the Miner sum of the per-aircraft terms
- Passa mix is at least as damaging as either aircraft alone (AC 6G §3.12.2.3 — designing to one aircraft is not the mix)
- Passdisabling the second slot (departures = 0) reproduces the single-aircraft engine result
- PassCDF scales linearly with departures (AC 6G §3.12.9.1: CDF = applied coverages / coverages to failure)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-rigid-published-web-validationrecords a differencePUBLISHED-VALUES: 3 -- distinct published values for this engine (engine-level total, declared once); independent audit A1: 2-3 published engine outputs; the remaining assertions are hand-derived or bands.5 passing
Analyses validated: faarfield-rigid
- PassAC 6G Appendix H.3: P-501 R = 600 psi, k = 100 pci, 20 yr → 17.14 in
- PassAC 6G Appendix H.9: R = 625 psi, k = 100.5 pci, same traffic, 20 yr → 16.7 in
- PassAC 6G Table 3-4 / Table 3-2: minimum rigid surface 6 in; P-501 modulus 4,000,000 psi with ν = 0.15
- Passdesign flexural strength range in AC 6G §3.16.7.3 (600-750 psi) gives monotone, physical slabs
- PassKawa, Brill & Hayhoe (2007) Eqs. (1)-(2) evaluated at the AC H.3 design factor (HAND-DERIVED)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
faarfield-rigid-web-validationWeb-benchmark validation for the FAARFIELD-class RIGID airfield design.6 passing
Analyses validated: faarfield-rigid
- PassFAARFIELD full-failure eq(2): C = 10^[(DF−0.5878)/0.2523]
- PassFAARFIELD onset eq(1): C = 10^[(DF−0.7409)/0.2465] (more conservative)
- PassCorps of Engineers LEA model: C = 10^[(DF−0.58901)/0.35486]
- PassWestergaard edge stress matches the closed-form hand calc
- PassAppendix-H rigid design reproduces the 17.14-in slab (closed form ≈ FE)
- Passrigid design is monotone in strength and traffic
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
irc-sp72-pavement-published-web-validationrecords a differenceLOW-VOLUME RURAL-ROAD PAVEMENT — `computeIrcSp72Pavement` (traffic curve A–D, minimum base course, sub-base split, bituminous-surfacing requirement) checked against the TEXT, TABLES AND WORKED EXAMPLES of two independent Indian Roads Congr…12 passing
Analyses validated: irc-sp72-pavement
- PassIRC:SP:72-2015 §1.3.3 — curve A/B/C/D for traffic categories 0-15 / 15-45 / 45-150 / 150-450 CVPD (mid-band inputs)
- PassIRC:SP:72-2015 §1.3.3 — minimum base course 150 mm for curves A and B, 225 mm for curves C and D
- PassIRC:SP:72-2015 §1.3.3 — "sub-base ... arrived at by subtracting the minimum base course thickness from the total" (derived: total 400 mm)
- PassIRC:SP:72-2015 Appendix A — the seven CVPD values of the ADT table fall on the curves §1.3.3 assigns them
- PassIRC:SP:72-2015 §1.3.4 — exemption (i): rainfall "less than 500 mm" and traffic "upto 150"
- PassIRC:SP:72-2015 §1.3.4 — exemption (ii): rainfall "less than 1000 mm" and traffic "upto 50"
- PassIRC:SP:72-2015 §6.1.2 — gravel-road floor "subgrade CBR is above 2": the engine warns at CBR 2 and not at 2.5
- PassIRC:SP:72-2015 Appendix D — CVPD 44 (6 HCV + 38 MCV), rainfall 750 mm, CBR 5: curve B, 150 mm base, gravel acceptable
- PassIRC:SP:20-2002 Table 5.1 — rainfall 0-500 mm: gravel at 0-50 and 50-150 motorised/day, bituminous at 150+
- PassIRC:SP:20-2002 Table 5.1 — rainfall 500-1000 mm: gravel only at 0-50; bituminous (single-coat SD or more) above
- PassIRC:SP:20-2002 Table 5.1 — rainfall 1000-1500 mm and 1500+ mm: bituminous surfacing at every traffic level
- PassIRC:SP:20-2002 §5.4.3 — 30 CVPD growing 6 % for 10 years = 54 CVPD → curve C; rainfall 1200 mm → "2 Coat Surface Dressing"
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
irc-sp72-pavement-web-validationFormula-fidelity validation against IRC:SP-72-2015 §1.3.3 (traffic-curve bands and minimum base-course thicknesses) and §1.3.4 (gravel/WBM surfacing exemptions).13 passing
Analyses validated: irc-sp72-pavement
- Pass[1-3] CVPD=10 (curve A, 0-15 band): min base=150mm, sub-base=250mm at 400mm total
- Pass[4-6] CVPD=30 (curve B, 15-45 band): min base=150mm
- Pass[7-9] CVPD=100 (curve C, 45-150 band): min base=225mm
- Pass[10-12] CVPD=300 (curve D, 150-450 band): min base=225mm
- Pass[13] the exact CVPD boundary values fall into the LOWER band (<=15 -> A, <=45 -> B, <=150 -> C)
- Pass[14] CVPD above 450 warns that it is outside the SP:72 curve range (use IRC 37 instead)
- Pass[15] exemption (i): arid climate (<500mm rain) with CVPD<=150 allows gravel/WBM surfacing
- Pass[16] exemption (ii): low-rainfall (<1000mm) with CVPD<=50 also allows gravel/WBM surfacing
- Pass[17] traffic too high for either exemption forces bituminous surfacing despite low rainfall
- Pass[18] high rainfall (>=1000mm) forces bituminous surfacing regardless of traffic
- Pass[19] no rainfall supplied assumes bituminous surfacing is required (never silently exempted)
- Pass[20] total thickness below the minimum base course flags the shortfall rather than a negative sub-base
- Pass[21] CVPD, CBR, and total thickness are each refused when invalid
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-cracking-published-web-validationPUBLISHED-ANSWER validation of the LOAD-STRESS SUB-MODEL inside `jpcp-cracking.ts`: the radius of relative stiffness ℓ and the Westergaard (1926) edge bending stress that feed the MEPDG fatigue calculation.6 passing
Analyses validated: jpcp-cracking
- PassPavement Interactive Examples 1 and 2: ℓ and edge stress, P = 9000 lb (a = 5.9 in), k = 200 pci, E = 5×10^6 psi
- PassIoannides et al. (1985) TRR 1043 Table 1 WESII — nine published edge stresses (E = 5×10^6 psi, P = 50 000 lb)
- PassIoannides et al. (1985) TRR 1043 Table 2 — printed L/ℓ for the 25 × 25 ft slab gives ℓ for the same nine runs
- PassIRC:58-2015 Appendix VII / VIII and Huang (2004): printed radius of relative stiffness
- PassSolved problem (ques10 post 34957): ℓ and edge stress in kg/cm units
- PassAASHTO (2015) MOP §5.4.1: N of Eq. 5-17b is the life at 50 percent slab cracking, so DI = 1 gives CRK = 50 %
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-cracking-web-validationFormula-fidelity validation against AASHTO MEPDG "A Manual of Practice" 2nd ed.8 passing
Analyses validated: jpcp-cracking
- Pass[1-6] base case (thick slab, light traffic): l=1055.9mm, sigma=1.4447MPa, Nf=9.975e7, DI=0.050125, CRK=0.266039%
- Pass[7-11] Westergaard b-branch (a < 1.724h), thinner slab + heavier traffic drives DI >> 1, CRK saturates at 100%
- Pass[12-16] the a >= 1.724h branch (b = a directly, not the Westergaard b formula) with a low tyre pressure over a thin slab
- Pass[17] N=0 gives exactly zero damage and zero cracking
- Pass[18] the fatigue-life exponent (C1=2.0, C2=1.22) matches Eq. 5-17b exactly at a controlled stress ratio
- Pass[19] stress_ratio field is sigma/MR (the inverse of the fatigue-equation ratio), consistent with edge_stress_mpa
- Pass[20] every load-bearing input is refused at 0 or below, never silently clamped to a tiny positive floor
- Pass[21] classification bands: below 5%, 5-15%, >=15%
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-faulting-published-web-validationrecords a differencePUBLISHED-VALUE validation of the two parts of `jpcp-faulting.ts` for which a published number could be found: the Westergaard (1926) loaded-corner deflection, and the effective base load-transfer efficiencies that enter the joint LTE of M…2 passing
Analyses validated: jpcp-faulting
- PassHuang (2004) Ch. 3 corner example: δc = 0.0502 in
- PassAASHTO (2015) MOP Table 5-3: effective base LTE 20 / 30 / 40 % (no dowels, no aggregate interlock → joint LTE = base LTE)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-faulting-web-validationFormula-fidelity validation against AASHTO MEPDG "A Manual of Practice" 2nd ed.9 passing
Analyses validated: jpcp-faulting
- Pass[1-6] base case (no dowels, aggregate base): LTE=52%, dL=0.044304 in, dUL=0.023038 in, DE=0.079135 lb/in, FAULTMAX0=0.126277 in
- Pass[7-9] dowel LTE=90% raises the joint LTE to 95.2% and cuts dUL/DE sharply (Eq. 5-22)
- Pass[10] lean-concrete base (LTE_base=40 vs 20 for aggregate) raises joint LTE to 64% at the same dowel/agg LTE
- Pass[11] loaded corner deflection dL is identical across base types and dowel LTE (Westergaard geometry is unaffected by LTE)
- Pass[12] no fines to erode (pct_passing_200 = 0) gives FAULTMAX0 = 0 by definition, with a warning
- Pass[13] no curling deflection (dcurl = 0) gives FAULTMAX0 = 0 by construction
- Pass[14] the Westergaard corner-ratio range guard refuses geometries outside a*sqrt(2)/l < 1.25
- Pass[15] joint LTE formula (Eq. 5-22) matches the compound-probability form exactly for arbitrary dowel/agg/base values
- Pass[16] every load-bearing input is refused at 0 or below
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-iri-published-web-validationPUBLISHED-COEFFICIENT cross-check of the MEPDG JPCP smoothness model (`jpcp-iri.ts`, IRI = IRI0 + C1·CRK + C2·SPALL + C3·TFAULT + C4·SF).2 passing
Analyses validated: jpcp-iri
- PassHall (2008) metric form of the MEPDG JPCP IRI model confirms the engine coefficients C1, C2, C3, C4
- PassThe misprinted C3 = 0.4929 of the 2008 interim MOP is rejected by the metric form
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-iri-web-validationFormula-fidelity validation against AASHTO MEPDG "A Manual of Practice" 2nd ed.8 passing
Analyses validated: jpcp-iri
- Pass[1-6] no freeze climate (FI=0): SF=9e-5, contributions crk=8.203 spall=2.2085 fault=4.4787 sf=0.00227, IRI=77.892472 in/mi
- Pass[7-9] freeze-thaw climate (FI=1500) raises the site factor and IRI to 79.785623 in/mi
- Pass[10-11] zero distress at age 0 returns exactly the initial IRI (63 in/mi)
- Pass[12-13] aged, more distressed case: SF=0.089216, IRI=110.018012 in/mi
- Pass[14] unit conversion in/mi -> m/km is exact (x0.0157828)
- Pass[15] IRI0 is refused at 0 or below — it is the dominant term, no pavement is built at IRI0=0
- Pass[16] each distress coefficient matches its published constant exactly, isolated one at a time
- Pass[17] ride-quality classification bands (good <95, fair <170, mediocre <220, else poor)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-spalling-published-web-validationPUBLISHED-VALUES: 12 -- distinct published values for this engine (engine-level total, declared once); independent audit A1: 12 chart readings; 23 further values are cross-checks against Hoerner Eq.7 passing
Analyses validated: jpcp-spalling
- PassHoerner et al. (2000) Fig. 38 — air content 2 / 4 / 6 / 8 % (f'c 5000 psi, 80 F-T/yr, 10 in, w/c 0.44)
- PassHoerner et al. (2000) Fig. 39 — 28-day compressive strength 2500 / 5000 / 7500 psi (air 6 %)
- PassHoerner et al. (2000) Fig. 40 — joint sealant: preformed vs non-preformed
- PassHoerner et al. (2000) Fig. 41 — slab thickness 8 / 10 / 12 in
- PassHoerner et al. (2000) Fig. 42 — annual freeze-thaw cycles 0 / 40 / 80 / 120 / 160
- PassHoerner et al. (2000) Fig. 43 — water/cement ratio 0.38 / 0.44 / 0.50
- PassHall (2008): each 1 % of air content shifts the age at 50 % spalling by "about 8 years"; preformed sealant gives essentially none over 60 years
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-spalling-web-validationFormula-fidelity validation against the AASHTO MEPDG "A Manual of Practice" 2nd ed.14 passing
Analyses validated: jpcp-spalling
- Pass[1-2] AGE=5, no sealant, AC=4%, fc=20MPa, FT=80, H=200mm, WC=0.55 -> SCF=316.9420, SPALL=21.685974%
- Pass[3-4] AGE=10, same mix -> SCF=236.9420, SPALL=35.782654%
- Pass[5-6] AGE=15 (base case) -> SCF=156.9420, SPALL=52.836675%
- Pass[7-8] AGE=20, same mix -> SCF=76.9420, SPALL=69.245718%
- Pass[9-10] AGE=25, same mix -> SCF=-3.0580, SPALL=81.895792%
- Pass[11-12] AGE=30, same mix -> SCF=-83.0580, SPALL=90.082316%
- Pass[13-14] preformed joint sealant at AGE=15 -> SCF=1556.9420, SPALL=0.103924%
- Pass[15] preformed sealant sharply reduces spalling vs no sealant, same age
- Pass[16-19] PCC air content sweep at AGE=15: 2%,4%,6%,8% -> 86.479524%, 52.836675%, 16.363403%, 3.302315%
- Pass[20-23] water/cement ratio sweep at AGE=15: 0.35,0.45,0.55,0.65 -> 39.633344%, 46.168327%, 52.836675%, 59.404008%
- Pass[24-27] slab thickness sweep at AGE=15: 150,200,250,300 mm -> 63.073483%, 52.836675%, 42.352301%, 32.512173%
- Pass[28-31] compressive strength sweep at AGE=15: 15,20,28,35 MPa -> 66.462497%, 52.836675%, 34.462553%, 23.082675%
- Pass[32-35] freeze-thaw cycles sweep at AGE=15: 0,40,80,150 -> 25.295769%, 38.117131%, 52.836675%, 76.125854%
- Pass[36] AGE=0 forces SPALL=0 exactly regardless of SCF (age-factor term AGE/(AGE+0.01)=0)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-time-stepping-published-web-validationrecords a differencePUBLISHED-ANSWER validation of the stress sub-model inside the JPCP time-stepping driver (`jpcp-time-stepping.ts`): the Westergaard (1926) load edge stress σ_L, the radius of relative stiffness ℓ, and the Bradbury (1938) edge curling stres…5 passing
Analyses validated: jpcp-time-stepping
- PassPavement Interactive Examples 1 and 2: ℓ and load edge stress
- PassPavement Interactive curling example: Bradbury edge warping stress 230 psi at C = 0.68
- PassIoannides et al. (1985) TRR 1043 Table 1 WESII — nine published edge stresses (E = 5×10^6 psi, P = 50 000 lb)
- PassIoannides et al. (1985) TRR 1043 Table 2 — printed L/ℓ (L = 300 in) gives ℓ for the same nine runs
- PassIRC:58-2015, Huang (2004) and the solved problem: printed radius of relative stiffness and edge stress
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
jpcp-time-stepping-web-validationValidation against AASHTO MEPDG Manual of Practice §5 (rigid distress) and Bradbury (1938) curling stress, via the engine's OWN documented self-check invariant (stated in its header): "with DeltaT = 0 every month...8 passing
Analyses validated: jpcp-cracking, jpcp-time-stepping
- Pass[1-2] SELF-CHECK INVARIANT (stated in the engine's own header): with zero monthly curling gradient, the accumulated damage exactly equals the single-pass jpcp-cracking engine's damage at the same total load
- Pass[3] the load-only edge stress reported by the time-stepping driver matches the Westergaard closed-form exactly (same formula as jpcp-cracking)
- Pass[4] adding a positive curling gradient can only INCREASE the peak combined stress above the load-only stress (Bradbury: curling adds to the bottom tensile stress in the critical direction)
- Pass[5] the accumulated damage is INVARIANT to the design life when the traffic is a fixed TOTAL (spreading the same total over more months does not add or remove traffic), per the engine's own documented E-110 note
- Pass[6] applications_per_month equals total_load_applications / (years*12) exactly
- Pass[7] the cracking curve is monotonically non-decreasing over time (damage only accumulates)
- Pass[8] faulting is explicitly flagged as NOT accumulated (the driver covers cracking only, per its own documented scope)
- Pass[9] invalid inputs (zero modulus, thickness, MR, or k) are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
layered-elastic-pavement-published-web-validationrecords a differenceMULTILAYER (BURMISTER) ELASTIC PAVEMENT RESPONSE — `computeLayeredElastic` / `subgradeStrainAtOffset` checked against PUBLISHED PROGRAM OUTPUT and a PUBLISHED TABLE.12 passing
Analyses validated: layered-elastic-pavement
- PassIRC:37-2018 Example II.1 — 500 mm of 119.7 MPa over a 66.6 MPa half-space, 40 kN wheel: surface deflection 1.41 mm
- PassIRC:37-2018 Example II.1 — the equivalent single-layer modulus 2(1−ν²)pa/δ = 105.10 MPa
- PassIRC:37-2018 Figure I.3 — 3000 / 450 / 75 MPa, 140 + 500 mm, dual wheel: top-of-subgrade εz 192.0 µε (r 0) and 205.3 µε (r 155)
- PassIRC:37-2018 Example II.2 / Figure II.3 — 95 MPa sub-base, 250 mm, over 50 MPa: εz 2322 µε (r 0), 2179 µε (r 155)
- PassIRC:37-2018 Example II.2 — the 150 mm trial (sub-base 0.2·150^0.45·50 = 95 MPa) gives 4324 µε
- PassIRC:37-2018 Example II.3 / Figure II.4 — 3000 / 200 / 62 MPa, 190 + 480 mm, dual wheel: εz 231.2 µε (r 0), 244.3 µε (r 155)
- PassIRC:37-2018 Table III.1 — bituminous + granular base/sub-base (granular modulus printed per row): 6 subgrade strains
- PassIRC:37-2018 Table III.6 — bituminous + 150 mm WMM + 200 mm CTSB: 5 subgrade strains
- PassIRC:37-2018 Table III.2 — bituminous + 100 mm crack-relief layer + CTB + 200 mm CTSB: 3 subgrade strains
- PassIRC:37-2018 Table III.4 — bituminous + 100 mm stabilised RAP (800 MPa) + 200 mm CTSB: 3 subgrade strains
- PassIRC:37-2018 Table III.5 — bituminous + 100 mm crack-relief + CTB + 200 mm GSB (167 MPa): 6 subgrade strains
- PassDas (2016) Table 6.1 — Δσ/q0 on the axis for 14 of the 16 printed depths between 0.1 and 4.0 (half-space values)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
layered-elastic-pavement-web-validationValidation against the classical Boussinesq (1885) closed-form solution for a uniform circular flexible load on a HOMOGENEOUS elastic half-space -- the exact analytical limit this multilayer Burmister solver reduces to when given a single…9 passing
Analyses validated: layered-elastic-pavement
- Pass[1] surface deflection matches the exact Boussinesq closed-form w0 = 2qa(1-nu^2)/E to 1e-6 relative
- Pass[2] subgrade vertical stress at the surface equals the applied pressure q exactly (sigma_z(0)=q boundary condition)
- Pass[3] tensile (radial) strain at the surface matches the exact Boussinesq closed-form to 1e-6 relative
- Pass[4] vertical strain via computeLayeredElastic and via subgradeInteriorStrains agree at z=0 (cross-consistency of the two entry points)
- Pass[5] deflection decays monotonically with layer stiffness (stiffer subgrade -> less deflection), the expected physical trend
- Pass[6] a real 3-layer pavement (AC/base/subgrade) gives a physically ordered response: deflection under the load exceeds zero, AC tensile strain and subgrade vertical strain are both positive and finite
- Pass[7] a stiffer asphalt layer reduces the tensile strain at its own bottom (the classic M-E design lever)
- Pass[8] multi-wheel gear superposition: a single wheel matches computeLayeredElastic's subgrade strain exactly, and adding wheels never decreases the max (elastic superposition can only add)
- Pass[9] gear amplification factor equals max gear strain divided by the single-wheel strain, exactly as defined
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-ac-rutting-web-validationValidation against AASHTO MEPDG "A Manual of Practice" 2nd ed.10 passing
Analyses validated: mepdg-ac-rutting
- Pass[1-2] the seasonal modulus-temperature law E=Eref.10^(susc.(Tref-T)) matches exactly at the default climate: summer E=865.209451 MPa, winter E=10402.105514 MPa
- Pass[3] the modulus law is symmetric about Tref=Tmean: shifting Tref by +5C at fixed climate shifts both summer/winter E by exactly 10^(susc.5)
- Pass[4-5] beta_r1 (field-calibration factor) scales the rut EXACTLY linearly, per Eq. 5-1a's direct multiplicative form
- Pass[6] monotone increasing in cumulative traffic N
- Pass[7] monotone increasing in mean pavement temperature (hotter asphalt is softer -> more rut)
- Pass[8] zero AC thickness gives exactly zero rut, labelled definitional (an unsurfaced road, not a durable pavement)
- Pass[9] zero load applications gives exactly zero rut, labelled definitional (never exercised, not adequate)
- Pass[10] mm/in conversion is exact (x25.4)
- Pass[11] negative thickness or negative traffic is refused, never read as "no asphalt"
- Pass[12] the strain-hardening term telescopes: rut(N1)/rut(N2) = (N1/N2)^0.4791 EXACTLY, whatever the life or climate (Eq. 5-1a, k3 = 0.4791)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-fatigue-published-web-validationMEPDG bottom-up fatigue (alligator) cracking - checks against PUBLISHED values only.16 passing
Analyses validated: mepdg-fatigue
- PassFig. 5-3 / Kim 2011 / Priest & Timm 2006: 50 % alligator cracking at 100 % damage (DI = 1), Hac = 2 in
- PassFig. 5-3 / Kim 2011 / Priest & Timm 2006: 50 % alligator cracking at 100 % damage (DI = 1), Hac = 4 in
- PassFig. 5-3 / Kim 2011 / Priest & Timm 2006: 50 % alligator cracking at 100 % damage (DI = 1), Hac = 6 in
- PassFig. 5-3 / Kim 2011 / Priest & Timm 2006: 50 % alligator cracking at 100 % damage (DI = 1), Hac = 8 in
- PassFig. 5-3 / Kim 2011 / Priest & Timm 2006: 50 % alligator cracking at 100 % damage (DI = 1), Hac = 12 in
- PassEq. 5-6a plateau C4/60 = 6000/60 = 100 %: at Log Damage (%) = 6 (DI = 1e4) the curve is at the plateau for Hac = 2, 6, 12 in
- PassFigure 5-3: the curve is indistinguishable from 0 % at Log Damage (%) <= -1 (DI = 0.001)
- PassPriest & Timm 2006 p. 80: the volumetric correction C is "equal to 1" at Va = 5 %, Vb = 11 %
- PassApp. II-1 Table 7, AC < 2 in: shift factor 0.000398 (checked at 1 in and 1.5 in, within the printed Se)
- PassApp. II-1 Table 7, AC 2-3 in: shift factor 0.000524 lies between the fitted curve at 2 in and at 3 in
- PassApp. II-1 Table 7, AC 3-4 in (printed "2-4"): shift factor 0.002934 lies between the fitted curve at 3 in and at 4 in
- PassApp. II-1 Table 7, AC 4-6 in: shift factor 0.004 (CH = 250), checked at 5 in within the printed Se
- PassApp. II-1 Table 7, AC 6-8 in: shift factor 0.004 (CH = 250), checked at 7 in within the printed Se
- PassApp. II-1 Table 7, AC 8-10 in: shift factor 0.004 (CH = 250), checked at 9 in within the printed Se
- PassApp. II-1 Table 7, AC 10-12 in: shift factor 0.004 (CH = 250), checked at 11 in within the printed Se
- PassApp. II-1 Table 7, AC > 12 in: shift factor 0.004 (CH = 250), checked at 14 in within the printed Se
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-fatigue-web-validationFormula-fidelity validation against AASHTO MEPDG "A Manual of Practice" 2nd ed.8 passing
Analyses validated: mepdg-fatigue
- Pass[1-6] base case (matches the existing hand-verified golden test exactly): C=0.41506, CH=250.0, Nf=1.010e9, D=0.00990, FCbottom=0.586%
- Pass[7-8] doubling the tensile strain drops Nf by exactly (200/70)^3.9492 per the published kf2=-3.9492 exponent
- Pass[9-10] doubling the AC modulus drops Nf by exactly 2^1.281 per the published kf3=-1.281 exponent
- Pass[11-12] the C-factor (air-voids/binder term) matches 10^(4.84.(Vbe/(Va+Vbe)-0.69)) exactly for an arbitrary mix
- Pass[13-14] the thickness-correction CH matches 1/(0.000398+0.003602/(1+e^(11.02-3.49.Hac))) exactly for an arbitrary thickness
- Pass[15] N=0 gives exactly zero damage and zero cracking, labelled as definitional (real limit: an untrafficked pavement)
- Pass[16] richer/lower-void mix (higher C-factor) increases Nf and reduces cracking than a leaner/higher-void mix, all else equal
- Pass[17] every load-bearing input is refused at 0 or below
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-iri-published-web-validationrecords a differenceMEPDG flexible-pavement IRI (Eq.19 passing
Analyses validated: mepdg-iri
- PassFHWA-HRT-17-049 Fig. 9 p02 = 20 %: predicted IRI change at age 1 yr = 0.18 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 9 p02 = 20 %: predicted IRI change at age 20 yr = 16.97 in/mi (printed to 2 d.p.)
- PassFHWA-HRT-17-049 Fig. 9 p02 = 40 %: predicted IRI change at age 1 yr = 0.2 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 9 p02 = 60 %: predicted IRI change at age 1 yr = 0.21 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 9 p02 = 60 %: predicted IRI change at age 20 yr = 18.44 in/mi (printed to 2 d.p.)
- PassFHWA-HRT-17-049 Fig. 10 Precip = 20 in: predicted IRI change at age 1 yr = 0.19 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 10 Precip = 20 in: predicted IRI change at age 20 yr = 17.67 in/mi (printed to 2 d.p.)
- PassFHWA-HRT-17-049 Fig. 10 Precip = 40 in: predicted IRI change at age 1 yr = 0.21 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 10 Precip = 40 in: predicted IRI change at age 20 yr = 18.57 in/mi (printed to 2 d.p.)
- PassFHWA-HRT-17-049 Fig. 10 Precip = 60 in: predicted IRI change at age 1 yr = 0.21 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 10 Precip = 60 in: predicted IRI change at age 20 yr = 19.1 in/mi (printed to 2 d.p.)
- PassFHWA-HRT-17-049 Fig. 11 FI = 100 F-days: predicted IRI change at age 1 yr = 0.18 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 11 FI = 100 F-days: predicted IRI change at age 20 yr = 16.05 in/mi (printed to 2 d.p.)
- PassFHWA-HRT-17-049 Fig. 11 FI = 500 F-days: predicted IRI change at age 1 yr = 0.2 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 11 FI = 500 F-days: predicted IRI change at age 20 yr = 18.2 in/mi (printed to 2 d.p.)
- PassFHWA-HRT-17-049 Fig. 11 FI = 900 F-days: predicted IRI change at age 1 yr = 0.21 in/mi (printed to 2 d.p., +/-0.01)
- PassFHWA-HRT-17-049 Fig. 11 FI = 900 F-days: predicted IRI change at age 20 yr = 18.98 in/mi (printed to 2 d.p.)
- PassFHWA Our Nation's Highways 2026: "IRI of less than 95 ... good": just below 95 in/mi the engine says Good ride, just above it does not
- PassFHWA Our Nation's Highways 2026: "less than 170 ... acceptable": just below 170 in/mi the engine says Fair ride, just above it does not
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-iri-web-validationFormula-fidelity validation against AASHTO MEPDG "A Manual of Practice" 2nd ed.7 passing
Analyses validated: mepdg-iri
- Pass[1-6] base case: SF=1397.063312, contributions rut=10.0 fat=6.0 thermal=1.6 site=20.955950, IRI=101.555950 in/mi
- Pass[7-8] age=0 zeroes the site factor (Age^1.5 multiplies both logarithms): SF=0, IRI=IRI0=63
- Pass[9] IRI0 refused at 0 or below
- Pass[10-11] p02 = 0 or p200 = 0 is refused (both sit inside logs and diverge to -infinity, not to a vanishing term)
- Pass[12] each distress coefficient matches its published constant exactly, isolated one at a time
- Pass[13] unit conversion in/mi -> m/km is exact (x0.0157828)
- Pass[14] ride-quality bands: good <95, fair <170, mediocre <220, else poor
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-subgrade-rutting-published-web-validationMEPDG unbound / subgrade rutting (Tseng-Lytton, Eq.25 passing
Analyses validated: mepdg-subgrade-rutting
- PassTable B-35 (and MOP Eq. 5-2c): Co = ln(a1/a9) = ln(0.15/20) = -4.8928523, the value the engine's Rho is built on
- PassTable B-35 CBR 1: Rho = 1.498e+34 at the published Beta 0.0299719 (MOP Eq. 5-2b)
- PassTable B-35 CBR 2: Rho = 10180000000000000 at the published Beta 0.0538458 (MOP Eq. 5-2b)
- PassTable B-35 CBR 3: Rho = 308500000000 at the published Beta 0.0700934 (MOP Eq. 5-2b)
- PassTable B-35 CBR 4: Rho = 2866000000 at the published Beta 0.0821515 (MOP Eq. 5-2b)
- PassTable B-35 CBR 5: Rho = 197251804 at the published Beta 0.0916235 (MOP Eq. 5-2b)
- PassTable B-35 CBR 7: Rho = 10004263 at the published Beta 0.1058432 (MOP Eq. 5-2b)
- PassTable B-35 CBR 10: Rho = 1073506.5 at the published Beta 0.1205232 (MOP Eq. 5-2b)
- PassTable B-35 CBR 12: Rho = 442991.9335 at the published Beta 0.127772481 (MOP Eq. 5-2b)
- PassTable B-35 CBR 15: Rho = 178595.56 at the published Beta 0.1363509 (MOP Eq. 5-2b)
- PassTable B-35 CBR 20: Rho = 69125.054 at the published Beta 0.146865 (MOP Eq. 5-2b)
- PassTable B-35 CBR 40: Rho = 14104.545 at the published Beta 0.1693629 (MOP Eq. 5-2b)
- PassTable B-35 CBR 100: Rho = 4164.0422 at the published Beta 0.1927432 (MOP Eq. 5-2b)
- PassTable B-35 CBR 1: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 2: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 3: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 4: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 5: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 7: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 10: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 12: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 15: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 20: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 40: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
- PassTable B-35 CBR 100: rut(N)/rut(1e7) follows the published ep(N)/er ratios at N = 1e3, 1e5, 1e8
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-subgrade-rutting-web-validationValidation against Tseng & Lytton (1989) and AASHTO MEPDG "A Manual of Practice" 2nd ed.10 passing
Analyses validated: mepdg-subgrade-rutting
- Pass[1-3] material regressions at Wc=15%, MR=60MPa: eps0/epsr=71.160108, beta=0.133119, rho=247542.176 (NHI 5.28-5.29 / MOP 5-2b exact)
- Pass[4-5] wetter subgrade (Wc=25% vs 15%) raises eps0/epsr per the +0.08109 coefficient exactly
- Pass[6-7] stiffer subgrade (higher MR) reduces eps0/epsr per the -0.000012157 coefficient exactly
- Pass[8] the granular/fine ks1 ratio (2.03/1.35) is EXACT — ks1 is a pure multiplicative factor on the rut
- Pass[9] monotone increasing in cumulative traffic N (the Tseng-Lytton accel factor e^(-(rho/N)^beta) rises toward 1 with N)
- Pass[10] N=0 gives exactly zero rut, labelled as definitional
- Pass[11] beta_s1=0 zeroes the rut exactly (it is a pure multiplicative local-calibration factor)
- Pass[12] linear in beta_s1 (a pure multiplicative calibration factor, Eq. 5-2a)
- Pass[13] every load-bearing input is refused at 0 or below, never silently clamped to a tiny positive floor
- Pass[14] mm/in conversion is exact (x25.4)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-thermal-cracking-published-web-validationrecords a differenceMEPDG thermal (transverse) cracking, Eq.11 passing
Analyses validated: mepdg-thermal-cracking
- PassNIST handbook critical value Z_0.001 = -3.09: TC = 400 x 0.001 = 0.4 ft/mi
- PassNIST handbook critical value Z_0.005 = -2.576: TC = 400 x 0.005 = 2 ft/mi
- PassNIST handbook critical value Z_0.01 = -2.326: TC = 400 x 0.01 = 4 ft/mi
- PassNIST handbook critical value Z_0.025 = -1.96: TC = 400 x 0.025 = 10 ft/mi
- PassNIST handbook critical value Z_0.05 = -1.645: TC = 400 x 0.05 = 20 ft/mi
- PassNIST handbook critical value Z_0.1 = -1.282: TC = 400 x 0.1 = 40 ft/mi
- PassNIST handbook worked example P[x <= -1] = 0.15866 => TC = 400 x 0.15866 = 63.464 ft/mi
- PassNIST handbook worked example P[x <= -1.53] = 0.06301 => TC = 400 x 0.06301 = 25.204 ft/mi
- PassN[0] = 0.5 (NIST: "add 0.5 (for the probability less than zero)"): Cd = HHMA gives TC = 400 x 0.5 = 200 ft/mi
- Passa crack that Paris-law growth drives through the whole layer saturates at the same published value 400 N[0] = 200 ft/mi
- PassNIST SP 811 App. B.8: 1 ft/mi = 0.3048 m / 1.609344 km, so m/km = ft/mi x 0.3048 / 1.609344 (0.1893939)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
mepdg-thermal-cracking-web-validationFormula-fidelity validation against AASHTO MEPDG "A Manual of Practice" 2nd ed.7 passing
Analyses validated: mepdg-thermal-cracking
- Pass[1-6] base case (mild climate, moderate mix): n=2.4, A=2.034249e-10, sigma_tip=1.2MPa, Cd=0.213912in, ratio=0.036222, TC=12.189030 ft/mi
- Pass[7-9] severe case (high modulus/contraction, thin brittle layer, many cycles) saturates at the TCMODEL ceiling of exactly 200 ft/mi
- Pass[10] alpha=0 (no thermal contraction) gives zero thermal stress and the crack never grows past its 0.1 in seed
- Pass[11] cooling_cycles=0 leaves the crack at its 0.1 in initial seed length, same TC as the alpha=0 case
- Pass[12] unit conversion ft/mi -> m/km uses the CORRECT constant 0.3048/1.609344 = 0.1893939, not the earlier transposed 0.18288
- Pass[13] every load-bearing input is refused at 0 or below
- Pass[14] thermal stress is capped at the mixture tensile strength (sigma_tip = min(sigM, E.alpha.dT))
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pavement-aashto-1993-fdot-fhwa-web-validationrecords a differenceAASHTO 1993 FLEXIBLE PAVEMENT (Eq.11 passing
Analyses validated: aashto-rigid-1993, pavement-aashto-1993
- PassFDOT §5.2.1 worked example — ESAL_D 5,000,000, MR 14,000 psi, R 90 % → SN_R = 3.57
- PassFDOT App. A — first-row/first-column and last-row/last-column cell of each of the 20 tables
- PassFDOT Table A.1A (R 75 %) — all 600 printed cells
- PassFDOT Table A.4A (R 90 %) — all 600 printed cells
- PassFDOT Table A.10A (R 99 %) — all 600 printed cells
- PassFHWA Ch. 6 §6.2.1 — baseline flexible design: W18 6.1×10⁶, R 90 %, S0 0.45, ΔPSI 1.7, MR 7,500 psi → SN 4.61
- PassFHWA Ch. 6 §6.3.1 — soft subgrade MR 3,800 psi → SN 5.76, and the baseline SN 4.61 carries only 1.25×10⁶ ESALs
- PassFHWA Ch. 6 §6.3.1 — soft-subgrade asphalt thickness D1 = (SN − m2·a2·D2)/a1 = 7.9 in
- PassFHWA Ch. 6 §6.5.1 — low-quality base: the baseline thicknesses give SN 3.4 which carries 0.88×10⁶ ESALs; D1 = 8.0 in
- PassFHWA Appendix C — flexible example: W18 11.6×10⁶, R 90 %, S0 0.45, ΔPSI 1.7, MR 7,500 psi → SN 5.07
- PassFHWA Table C-3 — standard normal deviate for all 18 reliability levels (incl. 99.99 % = −3.750, AASHTO Table 4.1)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pavement-aashto-1993-web-validationAASHTO 1993 FLEXIBLE PAVEMENT — web-validation benchmark against the Guide's own worked example.14 passing
Analyses validated: aashto-rigid-1993, pavement-aashto-1993
- PassAppendix H.1 — traffic, reliability and serviceability inputs
- PassFigure H.3 — relative damage u_f = 1.18e8 · MR^-2.32 at each tabulated modulus
- PassFigure H.3 — Σu_f = 5.446 over 24 half-months, ū_f = 0.227, MR_eff = 5,700 psi
- PassAppendix H.2 — SN = 5.6 from Figure 3.1 at MR 5,700, R 95 %, S0 0.35, ΔPSI 2.1, W18 18.6e6
- PassAppendix H.2 — Table H.2: swelling cuts the 15-year period to 13 years at W18 = 16.0e6, ΔPSI_TR = 1.89
- PassAppendix H.3 — SN1 = 3.2 above the base and SN2 = 4.5 above the subbase
- PassAppendix H.3 — layer thicknesses 8 in AC / 7 in base / 11 in subbase
- PassE-58 — the Guide’s minimum practical thicknesses are traffic-dependent
- PasscomputeAashto1993 reproduces Appendix H end to end
- Passthe single MR and the seasonal series agree when the series is constant
- PassEq 2.1 is monotone in every input, in the physically correct direction
- PassE-56 — layered design analysis reproduces Appendix H.3: SN1 3.2, SN2 4.5, 8 in AC, 7 in base
- PassE-56 — the SN-share fallback returns a 25 % thin surface on the Guide’s own example
- PassE-56 — a stiffer layer beneath thins the layer above, monotonically
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pavement-airfield-web-validationrecords a differenceWeb-benchmark validation for the FOURTEEN server-routed pavement and airfield engines.13 passing
Analyses validated: aashto-rigid-1993, acn-pcn-airfield, benkelman-overlay, crcp-punchout, faa-airfield-thickness, irc-sp72-pavement, jpcp-cracking, jpcp-faulting, jpcp-spalling, mepdg-ac-rutting, mepdg-fatigue, mepdg-iri, mepdg-subgrade-rutting, mepdg-thermal-cracking
- Passevery server-routed pavement/airfield slug is registered in PREMIUM_COMPUTES
- Passmepdg-fatigue keeps damage and cracking mutually consistent
- Passmepdg-ac-rutting and mepdg-subgrade-rutting convert inches to mm exactly
- Passmepdg-thermal-cracking converts ft/mi to m/km correctly (E-108)
- Passmepdg-iri sums its own reported distress contributions
- Passjpcp-cracking uses the Westergaard edge stress ratio
- Passjpcp-faulting keeps LTE, deflections and differential energy consistent
- Passjpcp-spalling and crcp-punchout stay bounded and convert correctly
- Passaashto-rigid-1993 solves Eq 3.1 and reproduces the design traffic
- Passacn-pcn-airfield applies the ICAO ACN/PCN overload rules
- Passfaa-airfield-thickness converts and responds correctly to CBR and load
- Passirc-sp72-pavement selects the right design curve and layer thicknesses
- Passbenkelman-overlay uses the IRC 81 characteristic deflection D_c = mean + 2σ
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pavement-calibration-web-validationWeb-benchmark validation for the Pavement-ME local-calibration presets — pins each preset's βr1/βs1/βf1 to the agency's published calibration report, and checks the preset actually overrides the national default in the engine.6 passing
Analyses validated: pavement-me
- PassNorth Carolina (NCDOT) preset matches the published final factors
- PassIdaho preset matches the published rutting factors (fatigue left national)
- PassArkansas preset carries the TRC1003 rut factor
- PassNational preset is the global default (1,1,1) and every preset cites a source
- Passselecting a preset OVERRIDES the beta inputs and applies the cited factors
- Pass'custom' leaves the explicit beta inputs in force (distinct from a preset)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pavement-irc-37-web-validationWeb-benchmark validation for `pavement-irc-37` — IRC 37:2018 flexible-pavement design.12 passing
Analyses validated: pavement-irc-37 · edited after the recorded run
- PassM_R from CBR follows IRC 37 Cl 4.4: 10·CBR below 5 %, 17.6·CBR^0.64 above
- PassM_R is capped at 100 MPa per Cl 4.4.1, and the cap is reported
- Passcumulative msa follows IRC 37 Cl 3.3 exactly
- Passthe fatigue equation reproduces IRC 37 Eqs 3.3/3.4 at both reliabilities
- Passthe rutting equation reproduces IRC 37 N_r = k·(1/ε_v)^4.5337
- Passthe granular modulus follows Cl 6.2 E = 0.2·h^0.45·M_R, capped at 5·M_R
- Passsurface course is the plate value (Plate 4, Fig 12.4, p. 39), and layers sum to the crust
- Passthickness rises with traffic and falls with subgrade strength
- Passthe CTB variants return their own plate section, not a scaled granular section
- Passthe catalogue verdict reflects the computed damage ratios
- Passthe bitumen grade and mean temperature both move the bituminous modulus
- Passinvalid inputs are refused, and every result carries IRC 37 clauses
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pavement-irc-58-appendix-v-web-validationrecords a differenceIRC 58:2015 Appendix-V regressions — validated against the code's OWN worked example (Appendix VII, "Illustrative Examples of Thickness Design", pp.13 passing
Analyses validated: pavement-irc-58
- PassIRC 58:2015 Appendix VII prints an inconsistent l — h=0.28 m is right, l=0.78758 m is the typo
- PassAppendix-V bottom-up single axle, Eq (V.3) — 12 published stresses (IRC 58:2015 Table VII.2)
- PassAppendix-V bottom-up tandem axle, Eq (V.9) — 12 published stresses (IRC 58:2015 Table VII.2)
- PassAppendix-V top-down, Eq (V.13) — 36 published stresses, single + tandem + tridem (Table VII.3)
- Passthe tridem top-down fraction is exactly 1/3, not the "33 %" the symbol list prints
- PassIRC 58:2015 fatigue Eqs (5)/(6) — the branch assignment, proven from Table VII.2
- Passreproduces IRC 58:2015 Table VII.4 cumulative fatigue damage — 20 published values exactly
- PassIRC 58:2015 Table VII.4 — the h = 0.29 m top-down row is inconsistent with the rest of the table
- Passthe engine's own spectrum loop agrees with the published Miner sum (E-18 share regression)
- Passthe Appendix-V path reproduces the example verdict: 280 mm rejected, 290 mm accepted
- Passthe legacy Westergaard proxy still runs, is labelled, and over-designs relative to the code
- Passdefault stress model is the code-compliant one
- PassE-19: omitting ΔT is flagged as UNSAFE, not as conservative
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pavement-irc-58-web-validationrecords a differenceC.IRC58 — `pavement-irc-58` web-benchmark against IRC 58:2015 itself, 26 cited values.8 passing
Analyses validated: pavement-irc-58
- PassC.IRC58.1: radius of relative stiffness matches the IRC 58 formula across 8 thicknesses
- PassC.IRC58.2: reproduces the PUBLISHED l = 0.78758 m exactly — at h = 350 mm (see erratum)
- PassC.IRC58.3: l scales as h^0.75 and k^-0.25, as the closed form requires
- PassC.IRC58.4: PCA fatigue law — the published stress-ratio regimes (Cl 5.8.6.1 Eqs 5–6)
- PassC.IRC58.5: Bradbury curling coefficient peaks near L/l ≈ 8-9, then eases to 1.0
- PassC.IRC58.6: the Appendix VII case runs, converges and lands in a plausible thickness band
- PassC.IRC58.7: IRC 58 Cl 5.4 night-time differential relation ΔT_night = ΔT_day/2 + 5
- PassC.IRC58.8: the output references cite the Appendix-V model actually used, and the legacy path still discloses
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pavement-me-web-validationPavement-ME driver (`pavement-me.ts`) - the design-reliability layer checked against PUBLISHED values, plus the decision on what kind of engine this is.9 passing
Analyses validated: pavement-me
- PassR = 50 %: IRI design shift = z x SEE = 0 x 18.9 in/mi (NIST z_R, MOP SEE_IRI)
- PassR = 90 %: IRI design shift = z x SEE = 1.282 x 18.9 in/mi (NIST z_R, MOP SEE_IRI)
- PassR = 95 %: IRI design shift = z x SEE = 1.645 x 18.9 in/mi (NIST z_R, MOP SEE_IRI)
- PassR = 97.5 %: IRI design shift = z x SEE = 1.96 x 18.9 in/mi (NIST z_R, MOP SEE_IRI)
- PassR = 99 %: IRI design shift = z x SEE = 2.326 x 18.9 in/mi (NIST z_R, MOP SEE_IRI)
- PassR = 99.5 %: IRI design shift = z x SEE = 2.576 x 18.9 in/mi (NIST z_R, MOP SEE_IRI)
- PassR = 99.9 %: IRI design shift = z x SEE = 3.09 x 18.9 in/mi (NIST z_R, MOP SEE_IRI)
- PassMOP Eqs. 5-3a-c: the total-rut design shift is z x [se(HMA) + se(granular) + se(fine)] of the engine's own layer ruts
- PassMOP Eq. 5-7: the fatigue design shift is z x [1.13 + 13/(1 + exp(7.57 - 15.5 log10(FC + 0.0001)))] at the engine's own FC
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
premium-fe-pavement-web-validationWeb-benchmark validation for the LAST EIGHT server-routed engines — the FE/pile group, layered-elastic and time-stepping pavement solvers.8 passing
Analyses validated: aircraft-gear-response, axle-load-spectra, faarfield-design, hs-layered-settlement, jpcp-time-stepping, lateral-pile-group, layered-elastic-pavement, pile-axial-load-transfer
- Passaxle-load-spectra reproduces the AASHTO fourth-power ESAL sum exactly
- Passhs-layered-settlement keeps its nonlinear and linear settlements consistent
- Passpile-axial-load-transfer closes its component sums across all t-z models
- Passlateral-pile-group applies p-multipliers and closes the efficiency definition
- Passlayered-elastic-pavement returns the two strains that drive the distress models
- Passaircraft-gear-response superposes wheels and reports the gear factor
- Passjpcp-time-stepping accumulates monthly damage over the design life
- Passfaarfield-design iterates the AC thickness to a cumulative damage factor of 1
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rigid-slab-response-published-web-validationPUBLISHED-ANSWER validation of the rigid-slab closed-form response (`rigid-slab-response.ts`): radius of relative stiffness ℓ and Westergaard (1926) interior / edge / corner bending stress, plus the Westergaard corner deflection.6 passing
Analyses validated: rigid-slab-response
- PassPavement Interactive Example 1: 9-in slab, 9000-lb FWD load (a = 5.9 in), k = 200 pci, E = 5×10^6 psi, μ = 0.15
- PassPavement Interactive Example 2: the same load on a 12-in slab
- PassHuang (2004) Ch. 3 examples: E = 4×10^6 psi, h = 10 in, k = 100 pci, P = 10 000 lb
- PassSolved problem (ques10 post 34957): P = 5100 kg, E = 3×10^5 kg/cm², h = 18 cm, μ = 0.15, K = 6 kg/cm³, a = 15 cm
- PassIoannides et al. (1985) TRR 1043 Table 1, column WESII: Westergaard ORIGINAL edge stress, semicircular load
- PassIRC:58-2015 Appendix VII / VIII: printed radius of relative stiffness, E = 30 000 MPa, μ = 0.15
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
rigid-slab-response-web-validationFormula-fidelity validation against Westergaard (1926/1948) and Ioannides, Thompson & Barenberg (1985) "Westergaard Solutions Reconsidered" (TRR 1043) -- the classical closed-form rigid-slab interior/edge/corner stress and deflection equat…10 passing
Analyses validated: rigid-slab-response
- Pass[1-4] interior loading: l=41.572647in, sigma=136.581313psi, d=0.005885in
- Pass[5-6] edge loading (same geometry): sigma=209.531712psi, d=0.020291in
- Pass[7-8] corner loading (same geometry): sigma=178.736926psi, d=0.044304in
- Pass[9] edge stress exceeds interior stress exceeds nothing in particular, but corner deflection is the largest of the three (physically expected ordering)
- Pass[10] the edge stress here matches jpcp-cracking's edge-stress formula at identical inputs (cross-engine consistency)
- Pass[11] the full engine reports the same closed-form critical stress as the standalone function, in MPa
- Pass[12-13] radius of relative stiffness and contact radius reported in mm match the hand-computed inch values x25.4
- Pass[14-15] stress ratio and factor of safety are exact reciprocals when MR is supplied
- Pass[16] without MR supplied, stress_ratio and stress_factor_of_safety are both null
- Pass[17] every load-bearing input is refused at 0 or below, never silently clamped to the 1psi floor
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
stabilization-mix-web-validationValidation for `stabilization-mix` — cement / lime stabilised-layer binder quantity and 7-day UCS acceptance against the IRC:SP:89 / MoRTH target band (`stabilization-mix.ts`).4 passing
Analyses validated: stabilization-mix
- PassIRC:37-2018 §7.3.2: CTSB 7-day UCS 1.5 to 3.0 MPa (IRC:SP:89)
- PassIRC:37-2018 §7.4: CTB UCS 4.5 to 7 MPa (IRC:SP:89)
- Passacceptance is inclusive at both published limits and refuses just outside them
- Passformula-fidelity: binder kg/m³ = (binder %/100) × dry density (Han Eq. 8.2-8.3)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Ground improvement
0 finite-element rows · 0 closed-form problems · 3 validation suites
Cited validation suites
deep-mixing-web-validation`deep-mixing` — anchored to the FHWA Ground Modification worked example.10 passing
Analyses validated: deep-mixing
- PassFHWA §3.3.3.2: the field UCS conversion 26 psi ≈ 3,700 psf is the manual’s own rounding
- PassFHWA §3.3.3.2: E50 = 150 × qu, and the engine uses that relation
- PassFHWA §3.3.3.2: the constrained modulus M = E50(1−ν)/((1+ν)(1−2ν)) with ν = 0.1
- PassE-46: FHWA §3.3.3.2 design shear strength = 0.5 × 0.8 × 1.0 × 0.63 × qu = 930 psf
- PassE-46: the PEAK strength is about twice the FHWA design strength — the unsafe gap
- PassE-46: without the Table 12 variability factor the design strength is NULL, not guessed
- PassE-46: the four factors are each honoured, and a factor > 1 is flagged
- Pass§3.3.3.2: at a_r < 1 the composite strength is the area-weighted blend
- Passthe treated unit weight increase the manual reports is physically modest
- Passevery numeric output is finite or an explicit null, and the source is cited
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
stone-columns-web-validationrecords a difference`stone-columns` — anchored to a published US (FHWA) source.10 passing
Analyses validated: stone-columns
- PassFHWA NHI-16-027 Eq. 5-1: α_sc = A_sc/A with A_sc = πd²/4 — an AREA ratio
- PassERRATUM (1): §4.3.2 uses s²/d² = 3.6 — the engine must NOT reproduce it
- PassFHWA NHI-16-027 Eqs. 5-3 to 5-5: load sharing is self-consistent at the engine’s n and α_sc
- PassFHWA NHI-16-027 §4.3.1: the RAP load-sharing chain reproduces exactly
- PassERRATUM (2): §4.3.1 prints a=de² but publishes Ra from a=(π/4)de²
- PassFHWA NHI-16-027 §4.3.1 / §4.3.2: published 1-D consolidation settlements reproduce
- PassPriebe (1995) n0 is reproduced at three column friction angles
- Passthe improvement factor is monotone in the two variables that physically drive it
- Passimproved settlement equals unimproved divided by the improvement factor
- Passevery output stays finite and the source is cited
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
vibro-compaction-web-validationrecords a difference`vibro-compaction` — anchored to FHWA Ground Modification Vol I.11 passing
Analyses validated: vibro-compaction
- PassFHWA Table 4-1: fines below 15 % and clay below 2 % is applicable
- PassFHWA §3.2: between 10 % and 15 % fines is applicable but outside the ideal zone B
- PassFHWA Table 4-1: the CLAY criterion is separate — a soil can pass on fines and fail on clay
- PassE-47: an unsupplied clay fraction is disclosed as UNCHECKED, not assumed compliant
- PassE-47: where Mitchell and FHWA disagree, BOTH verdicts are reported and the clash is flagged
- Passthe two sources agree at the extremes — so the disagreement flag is not always on
- PassFHWA §3.3: a target Dr above 85 % is challenged, quoting the manual
- PassFHWA Table 4-7 (Brown 1977): the backfill suitability-number bands are monotonic, and the printed 40-50 gap is real
- Passan unsuitable soil is credited with NO density improvement
- Passcloser spacing improves the achievable density, and the target is never exceeded
- Passevery numeric output is finite and the sources are cited
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Site investigation, in-situ and laboratory tests
0 finite-element rows · 0 closed-form problems · 25 validation suites
Cited validation suites
consistency-index-web-validationValidation for `consistency-index` — plasticity, liquidity and consistency indices and Skempton activity (`consistency-index.ts`, `computeConsistencyIndex`).10 passing
Analyses validated: consistency-index
- PassVarghese Example 1.4: 20 % finer than 0.002 mm, LL = 60 %, PL = 25 % ⇒ PI = 35 %, A = 1.75 > 1.25
- PassVarghese Example 1.5: LL = 45 %, PL = 25 % ⇒ PI = 20 %, and (LL − w)/PI = 1 at w = 25 %
- PassVarghese Eq. 1.1: Ic = 0 at the liquid limit (liquid) and Ic = 1 at the plastic limit
- PassVarghese Table 1.6: medium Ic 0.5–0.75, stiff 0.75–1.0, very stiff / hard above 1.0
- PassCraig (2012) and Holtz & Kovacs: activity < 0.75 inactive, 0.75–1.25 normal, > 1.25 active
- PassDas Table 2.6 endpoints: kaolinite 0.3–0.5, illite 0.5–1.2, montmorillonite 1.5–7.0
- PassDas Table 2.6 endpoints: halloysite 0.1–0.2 (hydrated) and 0.4–0.6 (dehydrated), attapulgite 0.4–1.3
- PassMitchell & Soga (2005) §4.6: Belle Fourche montmorillonite 1.24–7.09, Anna kaolinite 0.30–0.41
- PassDas §2.7, Holtz & Kovacs §2.7, FHWA Table 2-4: LI > 1 liquid (sensitive clay), LI < 0 brittle / overconsolidated
- PassIS 2720 (Part 5) §10–11 and Varghese: I_L + I_C = 1 for every input
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
cpt-analysis-web-validationWeb-benchmark validation for `cpt-analysis` — the CPT interpretation engine.9 passing
Analyses validated: cpt-analysis, cpt-sbt-ic
- Passrig: a 5 m reading at γ=20 with no water table gives σv = σv′ = 100 kPa
- PassSBT zones straddle every published Ic boundary (R&C 2012 p.26)
- PassIc matches the published definition at three points (R&C 2012 p.24)
- PassDr (Kulhawy & Mayne 1990) matches the published relation (R&C 2012 p.41)
- PassDr (Baldi et al. 1986) matches the published relation (R&C 2012 p.40)
- PassE-88: Dr correlations cross near Qcn 36 and diverge with density
- PassE-88: a dense sand profile warns that Dr is correlation-dependent
- PassE-87: φ′ agrees with the independent Kulhawy & Mayne form (R&C 2012 p.44)
- PassSu matches (qt - σv)/Nkt with the Lunne et al. (1997) default Nkt = 14
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
cpt-analysis-worked-examples-web-validationcpt-analysis — FULL WORKED EXAMPLES (the ≥20-value gate).17 passing
Analyses validated: cpt-analysis, cpt-sbt-ic
- Pass[DAS] Ex 3.4: σ′o = 200 kPa and the printed Qcn = 141.41
- Pass[DAS] Ex 3.4 with OCR 2: Q_OCR = OCR^0.18 (CPT Guide), NOT Das's printed OCR^1.8
- Pass[BOW] Ex 3-5: p′o = 89.2 kPa, qc/p′o = 330, φ ≈ 46° (Fig. 3-22b)
- Pass[BOW] Ex 3-6: po = 216 kPa, su = 600 kPa with Nk = 18
- Pass[BOW] Fig. 3-20: the Kulhawy-Mayne / Baldi band brackets Bowles's Dr ≈ 70 %
- Pass[RC] p. 45: tan φ′ = (1/2.68)[log(qc/σ′vo) + 0.29] — printed coefficients, not rounded
- Pass[RC] p. 45: Kulhawy & Mayne φ′ = 17.6 + 11 log(Qtn)
- Pass[RC] p. 42: Q_OCR = OCR^0.18 → Dr scales by OCR^−0.09
- Pass[RC] p. 42: Q_C 0.90 (low compressibility) → Dr scales by 0.90^−0.5
- Pass[RC] p. 42: Q_A = 1.2 + 0.05 log(t/100) → at t = 1000 yr, Q_A = 1.25
- Pass[RC] p. 42: Baldi Dr = (1/C2) ln(Qcn/C0), C0 = 15.7, C2 = 2.41
- Pass[RC] p. 42: invalid OCR (< 1) is refused, not silently used
- Pass[RC] p. 27: Ic zone boundaries 1.31 / 2.05 / 2.60 / 2.95 / 3.60
- Pass[BI] 2014 §2: the Ic chart centre (Q 2951, F 0.06026 %) gives Ic = 0
- PassIc parity: cpt-sbt-ic and icFromReading return the same Ic in very soft ground
- Pass[EC7] EN 1997-2 Table D.1: φ′ bands by qc, and Note (a) −3° for silty soil
- Pass[LUN] §9.2.2: past Dr = 100 % the correlation over-reads measured φ′, and says so
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
cpt-sbt-ic-web-validationrecords a differenceValidation for `cpt-sbt-ic` — Robertson (2009) normalised soil behaviour type index Ic with the stress exponent n iterated to convergence (`cpt-sbt-ic.ts`).5 passing
Analyses validated: cpt-sbt-ic
- PassNASEM 2024 Tables G3/G5: Ic, n, Qtn at 1.1-9.0 ft (clay-like and transitional near-surface layers)
- PassNASEM 2024 Tables G3/G5: Ic, n, Qtn at 10.0-20.8 ft (sand with silty seams)
- PassNASEM 2024 Tables G3/G5: Ic, n, Qtn at 24.8-52.5 ft (clean to silty sand)
- PassR&C 2012 / Niazi 2021: zone 7 < 1.31 < zone 6 < 2.05 < zone 5 < 2.60 < zone 4 < 2.95 < zone 3 < 3.60 < zone 2
- PassR&C 2012: behaviour is sand-like at Ic ≤ 2.50, clay-like above 2.70 and transitional between (NASEM rows)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
cptu-dissipation-web-validationrecords a differenceValidation for `cptu-dissipation` — Teh & Houlsby horizontal coefficient of consolidation from a CPTu dissipation test, ch = T*50·r²·√Ir / t50 (`cptu-dissipation.ts`).7 passing
Analyses validated: cptu-dissipation
- PassNiazi (2021) Table 2.18 / Eq. 2.120: T*50 = 0.245 (u2 shoulder) and 0.118 (u1 mid-face)
- PassLook Table 8.15: "multiply by 1.5 for 15 cm² piezocones" — the 15 cm² radius gives ×1.5 in ch
- PassLook Table 8.15: ch in cm²/min converts to the printed m²/yr (0.05, 0.5, 5.3, 53, 525, 10,500)
- PassLook Table 8.15 bands: ch at the band-centre t50 lies inside the printed ch band for Ir = 50-500
- Passformula-fidelity: Eq. 2.120 for a 10 cm² u2 cone, Ir = 100, t50 = 100 s
- Passformula-fidelity: ch scales as √Ir / t50 and as r²; u1 is 0.118/0.245 of u2 at equal inputs
- Passformula-fidelity: kh = ch·mv·γw with mv in m²/MN and γw = 9.81 kN/m³
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
dmt-web-validationrecords a differencePublished-benchmark validation for the flat dilatometer (DMT) interpretation (`dmt.ts`, `computeDmt`).13 passing
Analyses validated: dmt
- PassTC16 Fig. 31, z = 1.00 m (P0 1.2, P1 3.5, Σ′ 0.17, U 0.0 bar)
- PassTC16 Fig. 31, z = 1.20 m (P0 1.6, P1 3.4, Σ′ 0.21, U 0.0 bar)
- PassTC16 Fig. 31, z = 1.80 m (P0 2.4, P1 3.0, Σ′ 0.28, U 0.03 bar)
- PassTC16 Fig. 31, z = 2.00 m (P0 2.4, P1 2.8, Σ′ 0.29, U 0.05 bar)
- PassTC16 Fig. 31, z = 2.40 m (P0 1.9, P1 3.8, Σ′ 0.31, U 0.09 bar)
- PassTC16 Fig. 31, z = 3.20 m (P0 2.2, P1 6.0, Σ′ 0.36, U 0.17 bar)
- PassTC16 Fig. 31, z = 3.60 m (P0 2.0, P1 5.4, Σ′ 0.39, U 0.21 bar)
- PassTC16 Fig. 31, z = 3.80 m (P0 2.5, P1 6.8, Σ′ 0.41, U 0.23 bar)
- PassTC16 Fig. 31, z = 5.60 m (P0 3.2, P1 3.8, Σ′ 0.55, U 0.4 bar)
- PassTC16 Fig. 31, z = 7.40 m (P0 3.1, P1 5.8, Σ′ 0.68, U 0.58 bar)
- PassTC16 Fig. 31, z = 8.00 m (P0 3.1, P1 4.0, Σ′ 0.72, U 0.64 bar)
- PassTC16 Fig. 31, z = 9.00 m (P0 3.3, P1 4.0, Σ′ 0.79, U 0.74 bar)
- PassTC16 Fig. 31, z = 10.00 m (P0 3.4, P1 4.2, Σ′ 0.85, U 0.83 bar)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
ert-published-tables-web-validationrecords a differencePublished-value validation for `ert` — array geometric factors, median depth of investigation and the soil corrosivity bands.8 passing
Analyses validated: ert
- PassLoke (2004) Table 2.1: Wenner alpha — geometric factor 6.2832 and ze/a = 0.519 (a = 1 m)
- PassLoke (2004) Table 2.1: dipole-dipole geometric factors (a = 1 m), n = 1-8
- PassLoke (2004) Table 2.1: dipole-dipole median depth ze/a, n = 1-8
- PassLoke (2004) Table 2.1: Wenner-Schlumberger geometric factors (a = 1 m), n = 1-10
- PassLoke (2004) Table 2.1: Wenner-Schlumberger median depth ze/a, n = 1-10
- PassLoke (2004) Table 2.1: ze/L for Wenner-Schlumberger (L = AB = (2n+1)a) and dipole-dipole (L = (n+2)a)
- PassLoke (2004) Eq. (1.10): ρa = k·R with the printed Wenner factor 6.2832 (a = 1 m) and the printed DD n = 1 factor 18.850
- PassRoberge soil-corrosivity table: engine bands at the published edges (Ω·m = Ω·cm / 100)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
ert-web-validationWeb-benchmark validation for `ert` — array geometric factors, depth of investigation, and the VES forward model.11 passing
Analyses validated: ert
- Passthe analytical two-layer curves satisfy their own limits
- PassE-98: the Wenner forward model matches Telford Eq. (8.38) to <0.5 %
- PassE-98: the Wenner prefactor is 2a, and 4a is not a near miss
- PassE-98: the Schlumberger forward model matches Telford Eq. (8.39b) to <0.5 %
- PassE-98: the curve SHAPE is right, not just the magnitude
- PassE-98: Wenner inversion recovers a two-layer earth from the EXACT Wenner curve
- PassE-98: Schlumberger inversion recovers a two-layer earth from the EXACT curve
- Passgeometric factors K match the published array definitions
- Passρa = K·(V/I) reproduces a known homogeneous half-space
- Passcorrosivity bands break at the published NACE/Roberge edges
- Passthe governing corrosivity is the WORST layer, not an average
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
field-density-web-validationWeb-benchmark validation for `field-density` — in-situ density by sand replacement or core cutter.8 passing
Analyses validated: field-density
- Passcore cutter reproduces the IS 2720-29 chain on a hand-computed case
- Passsand replacement subtracts the cone/base-plate mass, per IS 2720-28
- Passomitting the cone correction over-states volume and under-reports compaction
- Passair voids reach zero exactly at full saturation
- Passan impossible (over-saturated) input is clamped and flagged, not returned negative
- Passthe compaction verdict follows the stated requirement, default 95 %
- Passa DoC above 102 % is flagged as a suspect Proctor reference
- Passboth methods name their IS standard
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
gradation-indices-web-validationPUBLISHED-VALUES: 12 -- distinct published values for this engine (engine-level total, declared once); independent audit A4: 12 distinct printed Cu/Cc values; the rest repeat them or are verdict/threshold checks.11 passing
Analyses validated: gradation-indices
- PassKnappett & Craig (2012) Ex. 1.1 — soil A: Cu = 34, Cz = 1.6, well-graded gravel (GW)
- PassKnappett & Craig (2012) Ex. 1.1 — soil B: Cu = 1.8, Cz = 0.95, uniform sand (SPu)
- PassKnappett & Craig (2012) Ex. 1.1 — soil C: Cu = 800, Cz = 0.25
- PassFHWA-NHI-06-088 Fig. 4-2 — curve A: Cu = 8.0, Cc = 0.9, fails the Table 4-10 well-graded criteria
- PassFHWA-NHI-06-088 Fig. 4-2 — curve B: Cu = 2.0, Cc = 1.12, criteria say poorly graded
- PassFHWA-NHI-06-088 Fig. 4-2 — curve C: Cu = 1.4, Cc = 1.2, poorly graded
- PassFHWA-NHI-06-088 Fig. 4-2 — curve A through the registry (RUNNER_CONFIGS) gives the printed indices
- PassASTM D2487 X1.1.1 — Cu = 12.4, Cc = 2.7 gravel is classified GW (well graded)
- PassASTM D2487 X2.4.3 — Cu = 1.9, Cc = 2.4 gravel is classified GP (poorly graded)
- PassBowles (1996) — sand with Cu = 7, Cc = 1.3 is "well-graded ... SW"
- PassASTM D2487 Table 1 — gravel needs Cu >= 4, sand needs Cu >= 6, both need 1 <= Cc <= 3
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
index-outputs-web-validationindex-outputs-web-validation.test.ts5 passing
Analyses validated: barton-bandis, soil-classification, steel-pile-section
- Passsoil-classification: AASHTO group index matches M 145 Cl 5.4 and is floored at 0 with no upper cap (7 anchors)
- Passsoil-classification: the Casagrande chart places soils on the right side of the A-line (8 anchors)
- Passsoil-classification: every displayed output is present and non-empty on the defaults
- Passbarton-bandis: φ_peak = φ_r + JRC·log₁₀(JCS/σ′n), and τ follows from it (8 anchors)
- Passsteel-pile-section: the elastic and plastic moduli are consistent with each other and the shape
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
index-properties-web-validationWeb-benchmark validation for NINE index-property, classification and stress-state runner engines.9 passing
Analyses validated: compression-index, consistency-index, consolidation-degree, gradation-indices, phase-relations, pore-pressure-parameters, quick-condition, soil-classification, stress-path
- Passphase-relations satisfies every phase-diagram identity exactly
- Passconsistency-index reproduces the Atterberg definitions and Skempton activity
- Passgradation-indices computes C_u and C_c and applies the ASTM D2487 criteria
- Passcompression-index reproduces all five published C_c correlations
- Passsoil-classification places the soil on the Casagrande chart and computes the AASHTO GI
- Passstress-path computes both invariant pairs and the M line consistently
- Passpore-pressure-parameters follows Skempton (1954) Δu = B[Δσ₃ + A(Δσ₁ − Δσ₃)]
- Passquick-condition uses the Terzaghi critical gradient (G_s − 1)/(1 + e)
- Passconsolidation-degree inverts the Terzaghi U-T_v relation both ways
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
phase-relations-web-validationrecords a differenceValidation of the soil phase-relation engine (`phase-relations.ts`) against PUBLISHED worked examples and PUBLISHED problem answers.9 passing
Analyses validated: phase-relations
- PassDas (2016) Ex. 2.1 — 1.8 kN in 0.1 m³, w = 12.6 %, Gs = 2.71
- PassDas (2016) Ex. 2.3 — γ = 19.2 kN/m³, w = 9.8 %, Gs = 2.69
- PassDas (2016) Ex. 2.4 — densities and the water needed to saturate (Gs = 2.68, e = 0.83)
- PassDas (2016) Ex. 2.2 — n = 0.387, ρd = 1600 kg/m³ gives e = 0.631 with the printed Gs = 2.61
- PassDas (2016) Ex. 2.6 — γ = 108 pcf, w = 8 %, Gs = 2.65 (US units)
- PassDas (2016) Problem 2.1 — 87.5 kg in 0.05 m³, w = 15 %, Gs = 2.68 (printed answers)
- PassDas (2016) Problem 2.2 — saturated soil: the printed γd and Gs give back γsat = 20.1 kN/m³
- PassDas (2016) Problem 2.3 — γ = 119.5 pcf, w = 12 %, Gs = 2.65 (printed answers)
- PassKnappett & Craig (2012) Ex. 1.2 — ρ = 1990 kg/m³, w = 12.5 %, Gs = 2.68
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pore-pressure-parameters-web-validationValidation for `pore-pressure-parameters` — Skempton's A and B pore-pressure parameters (`pore-pressure-parameters.ts`).9 passing
Analyses validated: pore-pressure-parameters
- PassSkempton (1954) Table 1: Δu for isotropic cell-pressure steps of 15, 30, 45, 60 lb/in²
- PassLambe & Whitman Fig. 26.14: Δu = 85.2 + 0.85(110.6) = 179.2 kN/m²
- PassItasca / Lambe & Whitman embankment: A = 1/3, Δσ1 = 4180, Δσ3 = 1645 psf → Δu = 2490 psf
- PassCraig 7th Solutions (CU test, back pressure 200): A_f = 0.73 reproduces the measured Δu = 433 − 200 = 233 kN/m²
- PassSkempton (1954) alternative form: A = 1/3 gives Δu = B(Δσ1 + 2Δσ3)/3
- PassDas (2016) p. 63 A at failure: sandy clays 0.5-0.7, NC clays 0.5-1, OC clays −0.5-0 are accepted
- PassLambe & Whitman Table 26.1 A at failure: 0.7-1.3 NC, 0.3-0.7 lightly OC, −0.5-0 heavily OC are accepted
- PassLambe & Whitman Table 26.1 A at failure: sensitive clay 1.5-2.5 and very loose fine sand 2-3 are accepted
- PassLambe & Whitman Table 26.1 B: saturated soils B ≈ 1; Boulder clay at S = 93, 87, 76 % has B = 0.69, 0.33, 0.10
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pressuremeter-menard-published-web-validationPublished-table validation for the Ménard pressuremeter footing engine (`pressuremeter-menard.ts`, `computePressuremeterMenard`).27 passing
Analyses validated: pressuremeter-menard
- Pass[NF] Tableau H.2.1.1.3: L/B = 1 → λc = 1.10, λd = 1.12
- Pass[NF] Tableau H.2.1.1.3: L/B = 2 → λc = 1.20, λd = 1.53
- Pass[NF] Tableau H.2.1.1.3: L/B = 3 → λc = 1.30, λd = 1.78
- Pass[NF] Tableau H.2.1.1.3: L/B = 5 → λc = 1.40, λd = 2.14
- Pass[NF] Tableau H.2.1.1.3: L/B = 20 → λc = 1.50, λd = 2.65
- Pass[EC7] Table E.2: L/B = 1 → λc = 1.1, λd = 1.12
- Pass[EC7] Table E.2: L/B = 2 → λc = 1.2, λd = 1.53
- Pass[EC7] Table E.2: L/B = 3 → λc = 1.3, λd = 1.78
- Pass[EC7] Table E.2: L/B = 5 → λc = 1.4, λd = 2.14
- Pass[EC7] Table E.2: L/B = 20 → λc = 1.5, λd = 2.65
- Pass[NF] Tableau H.2.1.1.1 Argile: surconsolidé 1, normalement consolidé 2/3, sous-consolidé 1/2
- Pass[NF] Tableau H.2.1.1.1 Limon: surconsolidé 2/3, normalement consolidé 1/2, sous-consolidé 1/2
- Pass[NF] Tableau H.2.1.1.1 Sable: surconsolidé 1/2, normalement consolidé 1/3, sous-consolidé 1/3
- Pass[NF] Tableau H.2.1.1.1 Grave: surconsolidé 1/3, normalement consolidé 1/4
- Pass[NF] Tableau H.2.1.1.1 Tourbe (normalement consolidée): α = 1
- Pass[NF] Tableau H.2.1.1.2 Rocher: très peu fracturé 2/3, normal fracturé 1/2, très fracturé 1/3 (engine weathered_rock: OC/NC/UC)
- Pass[EC7] Table E.3 Clay: over-consolidated 1, normally consolidated 0,67, remoulded 0,5
- Pass[EC7] Table E.3 Silt: over-consolidated 0,67, normally consolidated 0,5
- Pass[EC7] Table E.3 Sand: EM/pLM > 12 → 0,5 (over-consolidated); 5–12 → 0,33 (normally consolidated)
- Pass[EC7] Table E.3 Sand and gravel: EM/pLM > 10 → 0,33; 6–10 → 0,25
- Pass[EC7] Table E.3 Peat 1; Rock: extensively fractured 0,33, unaltered 0,5, weathered 0,67
- Pass[NF] Tableau D.2.3: kp0 = 0.8 (clay strip Q1 / square Q2) and 1 (sand strip Q3 / square Q4) at De/B = 0
- Pass[NF] Tableau D.2.3: kp0 = 0.8 for chalk (Q5 strip / Q6 square) and marl–weathered rock (Q7 / Q8)
- Pass[NF] Figure D.2.3 plateau De/B ≥ 2: Q1 (clay strip) 1.024 and Q2 (clay square) 1.128
- Pass[NF] Figure D.2.3 plateau: Q3 (sand strip) and Q7 (marl strip) overlap at 1.397
- Pass[NF] Figure D.2.3 plateau: Q4 (sand square) 1.581 digitised; Q8 (marl square) from the PRINTED coefficients
- Pass[NF] Figure D.2.3 plateau: Q5 (chalk strip) 1.518 and Q6 (chalk square) 1.768
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
pressuremeter-menard-web-validationFormula-fidelity validation against NF P94-261 (Calcul geotechnique -- Fondations superficielles), Annexes D and H -- the French national pressuremeter foundation-design standard.8 passing
Analyses validated: pressuremeter-menard
- Pass[1-3] square footing, clay/silt, NC: kp=1.012734, qnet=607.640684 kPa, alpha=0.666667
- Pass[4-6] shape coefficients lambda_c=1.10, lambda_d=1.12 at L/B=1 (the Tableau H.2.1.1.3 anchor)
- Pass[7-9] settlement components: spherical=5.500000mm, deviatoric=10.829549mm, total=16.329549mm
- Pass[10] a strip footing (L>>B) uses a materially different kp than a square footing at the same De/B, per the strip/square interpolation on B/L
- Pass[11] a stiffer soil (higher EM) reduces both settlement components proportionally (sc and sd are both inversely proportional to EM)
- Pass[12] the overconsolidated state gives a HIGHER alpha (stiffer response) than normally-consolidated for clay/silt (Tableau H.2.1.1.1: OC=1, NC=2/3)
- Pass[13] De/B beyond 2 clamps kp at the De/B=2 plateau and warns, per NF P94-261 D.2.3's stated validity range
- Pass[14] invalid inputs (zero width, zero modulus, zero limit pressure) are refused
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
site-investigation-web-validationWeb-benchmark validation for `site-investigation` — borehole layout and depth planning across four national codes.13 passing
Analyses validated: site-investigation
- PassIS 1892 Cl 3.3 depths are 1.5·B (isolated), 2.0·B (combined), 1.5·B (raft), + Df
- PassIS 2911-1 Cl 6.5 takes pile exploration to L + 5·B below the toe
- Passthe depth rule changes with the code, as the codes themselves differ
- Passthe deepest applicable floor governs, and the reason is named
- PassIS 1893 liquefaction screening drives depth in zones III-V with shallow groundwater
- Passstorey influence follows Tomlinson D = C·S^0.7 and can govern
- Passborehole counts rise with area, importance and complexity
- Passspacing is consistent with the count and the footprint
- Passscale bands follow the borehole count
- PassSPT quantity follows the 1.5 m interval over the full depth, per borehole
- Passeach code returns its own reference set, not a union
- Passspecial ground conditions add their own tests, each with a standard
- Passinvalid inputs are refused with a zeroed plan
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
site-practice-web-validationWeb-benchmark validation for TWELVE site-practice runner engines — slope charts, in-situ test corrections, RC checks, uplift, stress distribution, frost, permeability, piping, eccentricity, two-layer bearing, filters and collapse.12 passing
Analyses validated: collapse-potential, eccentric-footing-pressure, filter-design, flotation, frost-depth, grain-size-permeability, punching-shear, taylor-stability, two-layer-bearing, vane-correction, vertical-stress-increase, weighted-creep
- Passtaylor-stability inverts the Taylor (1937) stability number both ways
- Passvane-correction applies Bjerrum (1972/73) μ = 1.7 − 0.54 log₁₀(PI)
- Passpunching-shear follows IS 456:2000 Cl 31.6.3
- Passflotation checks uplift to EN 1997-1 §2.4.7.4 (UPL)
- Passvertical-stress-increase matches the Boussinesq rectangular integral
- Passfrost-depth reproduces Stefan and the Modified Berggren correction
- Passgrain-size-permeability reproduces Hazen and Kozeny-Carman
- Passweighted-creep reproduces Bligh (1910) and Lane (1935) creep theory
- Passeccentric-footing-pressure applies the middle-third rule and Meyerhof width
- Passtwo-layer-bearing selects the right mode and uses exact bearing factors
- Passfilter-design applies the Terzaghi and USACE filter criteria
- Passcollapse-potential follows ASTM D5333 and the Jennings & Knight bands
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
skempton-bjerrum-web-validationPUBLISHED-VALUES: 12 -- distinct published values for this engine (engine-level total, declared once); independent audit A4: 12 printed values; about 20 of the 29 assertions are the suite author's chart digitisation.9 passing
Analyses validated: skempton-bjerrum
- Pass[C] Craig Fig 8.29 — circular-footing lines are μ = A + α(1−A) with the printed intercepts
- Pass[C] Craig Fig 8.29 — right-hand end of the circular lines (A = 1.2, sensitive-clay side), digitised
- Pass[C] Craig Fig 8.29 — all circular lines cross at μ ≈ 0.99 at A = 1
- Pass[D] Das Fig 7.22 — circular lines at A = 0 (intercepts) and A = 0.5, 0.9
- Pass[C] Craig Example 8.5 — 6 m square footing on stiff clay: μc = 0.55, s_c = 64 mm, total 73 mm
- Pass[C] Craig Example 8.5 — μc = 0.55 at A = 0.35 agrees with the α interpolated from Fig 8.29 at H/B = 2.2
- Pass[D] Das Example 7.10 — K_cr = 0.78 at A = 0.6, H_c/B_eq = 0.64; S_c = 0.78 × 46.5 ≈ 36.3 mm
- Pass[D] Das Example 7.10 — K_cr at H_c/B = 0.64 falls between the printed H/B = 0.5 and 1.0 lines at A = 0.6
- Pass[L][C] Look Table 23.4 (← Tomlinson 1995) correction-factor bands vs Craig p.308 ranges of A
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
skempton-pore-pressure-web-validationValidation for Skempton pore-pressure parameters (`skempton-pore-pressure.ts`).5 passing
Analyses validated: not attributed by the manifest
- Passisotropic loading (Δσ1=Δσ3): Δu = B·Δσ3 (A irrelevant)
- Passpure deviatoric (Δσ3=0): Δu = B·A·Δσ1
- PassB parameter: saturated (C_f→0) → 1; compressible fluid < 1
- Passundrained ESP: CU triaxial (Δσ3=0), NC clay A=0.9 B=1
- Passtotal stress path (TSP) minus Δu equals effective stress path
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
soil-classification-web-validationrecords a differenceValidation of the soil-classification engine (`classification.ts`, slug `soil-classification`): USCS (ASTM D2487), its IS 1498 L/I/H variant, and AASHTO M 145 / D3282 with Group Index.25 passing
Analyses validated: soil-classification
- PassDas (2016) Problem 2.6 — soil A is AASHTO A-7-6(9)
- PassDas (2016) Problem 2.6 — soil B is AASHTO A-6(5)
- PassDas (2016) Problem 2.6 — soil C is AASHTO A-3(0)
- PassDas (2016) Problem 2.6 — soil D is AASHTO A-4(5)
- PassDas (2016) Problem 2.6 — soil E is AASHTO A-2-6(1)
- PassDas (2016) Problem 2.6 — soil F is AASHTO A-7-6(19)
- PassDas (2016) Problem 2.7 — soil A is ML, Sandy silt
- PassDas (2016) Problem 2.7 — soil B is ML, Sandy silt
- PassDas (2016) Problem 2.7 — soil D is ML, Sandy silt
- PassDas (2016) Problem 2.7 — soil E is SM, Silty sand
- PassDas (2016) Problem 2.7 — soil F is CH, Fat clay with sand
- PassDas (2016) Problem 2.6/2.7 — soils A and F through RUNNER_CONFIGS give the printed answers
- PassASTM D2487 X1.1.1 — 73 % gravel, 23 % sand, 4 % fines, Cc = 2.7, Cu = 12.4 → GW, well-graded gravel with sand
- PassASTM D2487 X1.1.2 — 61 % sand, 23 % fines (LL 33, PI 6), 16 % gravel → SM, silty sand with gravel
- PassASTM D2487 Note 11 — 46 % gravel, 30 % sand, 24 % clayey fines (LL 38, PI 19) → GC, clayey gravel with sand
- PassASTM D2487 X2.4.3 — broken shells: 65 % gravel, 31 % sand, 4 % fines, Cc = 2.4, Cu = 1.9 → GP, poorly graded gravel with sand
- PassASTM D2487 X2.4.4 — crushed rock: 89 % gravel, 11 % sand, Cc = 2.4, Cu = 0.9 → GP, poorly graded gravel
- PassASTM D2487 X2.4.1 — 61 % clayey fines (LL 37, PI 16), 33 % sand, 6 % gravel → CL, sandy lean clay
- PassASTM D2487 X1.1.3 — 100 % organic fines, LL (not dried) 32, PI 10 → OL, organic clay
- PassASTM D2487 Note 10 — poorly graded sand, 10 % fines, LL 20, PI 6 (CL-ML fines) → SP-SC
- PassKnappett & Craig (2012) Ex. 1.1 — soil A (100 % coarse, Cu = 34, Cz = 1.6) is GW
- PassKnappett & Craig (2012) Ex. 1.1 — soil B (3 % fines, 2 % gravel, Cu = 1.8, Cz = 0.95) is SP
- PassKnappett & Craig (2012) Ex. 1.1 — soil C (34 % fines LL 26 PI 9, 41 % gravel, 25 % sand) is GC
- PassKnappett & Craig (2012) Ex. 1.1 — soil D (LL 42, PI 18, 95 % fines) is CI under the IS 1498 intermediate class
- PassFHWA-NHI-06-088 — the group index is not capped at 20 (F = 100, LL = 90, PI = 65)
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
spt-correction-web-validationspt-correction — published-value validation (the ≥20-value gate).128 passing
Analyses validated: spt-correction
- Pass[DAS-T3.7] Eq. 3.13 (liao_whitman) at σ′/p_a = 0.25 → C_N 2
- Pass[DAS-T3.7] Eq. 3.13 (liao_whitman) at σ′/p_a = 0.5 → C_N 1.41
- Pass[DAS-T3.7] Eq. 3.13 (liao_whitman) at σ′/p_a = 0.75 → C_N 1.15
- Pass[DAS-T3.7] Eq. 3.13 (liao_whitman) at σ′/p_a = 1 → C_N 1
- Pass[DAS-T3.7] Eq. 3.13 (liao_whitman) at σ′/p_a = 1.5 → C_N 0.82
- Pass[DAS-T3.7] Eq. 3.13 (liao_whitman) at σ′/p_a = 2 → C_N 0.71
- Pass[DAS-T3.7] Eq. 3.13 (liao_whitman) at σ′/p_a = 3 → C_N 0.58
- Pass[DAS-T3.7] Eq. 3.13 (liao_whitman) at σ′/p_a = 4 → C_N 0.5
- Pass[DAS-T3.7] Eq. 3.14 (skempton) at σ′/p_a = 0.25 → C_N 1.6
- Pass[DAS-T3.7] Eq. 3.14 (skempton) at σ′/p_a = 0.5 → C_N 1.33
- Pass[DAS-T3.7] Eq. 3.14 (skempton) at σ′/p_a = 0.75 → C_N 1.14
- Pass[DAS-T3.7] Eq. 3.14 (skempton) at σ′/p_a = 1 → C_N 1
- Pass[DAS-T3.7] Eq. 3.14 (skempton) at σ′/p_a = 1.5 → C_N 0.8
- Pass[DAS-T3.7] Eq. 3.14 (skempton) at σ′/p_a = 2 → C_N 0.67
- Pass[DAS-T3.7] Eq. 3.14 (skempton) at σ′/p_a = 3 → C_N 0.5
- Pass[DAS-T3.7] Eq. 3.14 (skempton) at σ′/p_a = 4 → C_N 0.4
- Pass[DAS-T3.7] Eq. 3.15 (skempton_coarse) at σ′/p_a = 0.25 → C_N 1.33
- Pass[DAS-T3.7] Eq. 3.15 (skempton_coarse) at σ′/p_a = 0.5 → C_N 1.2
- Pass[DAS-T3.7] Eq. 3.15 (skempton_coarse) at σ′/p_a = 0.75 → C_N 1.09
- Pass[DAS-T3.7] Eq. 3.15 (skempton_coarse) at σ′/p_a = 1 → C_N 1
- Pass[DAS-T3.7] Eq. 3.15 (skempton_coarse) at σ′/p_a = 1.5 → C_N 0.86
- Pass[DAS-T3.7] Eq. 3.15 (skempton_coarse) at σ′/p_a = 2 → C_N 0.75
- Pass[DAS-T3.7] Eq. 3.15 (skempton_coarse) at σ′/p_a = 3 → C_N 0.6
- Pass[DAS-T3.7] Eq. 3.16 (skempton_oc) at σ′/p_a = 0.25 → C_N 1.78
- Pass[DAS-T3.7] Eq. 3.16 (skempton_oc) at σ′/p_a = 0.75 → C_N 1.17
- Pass[DAS-T3.7] Eq. 3.16 (skempton_oc) at σ′/p_a = 1 → C_N 1
- Pass[DAS-T3.7] Eq. 3.16 (skempton_oc) at σ′/p_a = 1.5 → C_N 0.77
- Pass[DAS-T3.7] Eq. 3.16 (skempton_oc) at σ′/p_a = 2 → C_N 0.63
- Pass[DAS-T3.7] Eq. 3.16 (skempton_oc) at σ′/p_a = 3 → C_N 0.46
- Pass[DAS-T3.7] Eq. 3.16 (skempton_oc) at σ′/p_a = 4 → C_N 0.36
- Pass[DAS-T3.7] Eq. 3.17 (seed_1975) at σ′/p_a = 0.25 → C_N 1.75
- Pass[DAS-T3.7] Eq. 3.17 (seed_1975) at σ′/p_a = 0.5 → C_N 1.38
- Pass[DAS-T3.7] Eq. 3.17 (seed_1975) at σ′/p_a = 0.75 → C_N 1.15
- Pass[DAS-T3.7] Eq. 3.17 (seed_1975) at σ′/p_a = 1 → C_N 1
- Pass[DAS-T3.7] Eq. 3.17 (seed_1975) at σ′/p_a = 1.5 → C_N 0.78
- Pass[DAS-T3.7] Eq. 3.17 (seed_1975) at σ′/p_a = 2 → C_N 0.62
- Pass[DAS-T3.7] Eq. 3.17 (seed_1975) at σ′/p_a = 3 → C_N 0.4
- Pass[DAS-T3.7] Eq. 3.17 (seed_1975) at σ′/p_a = 4 → C_N 0.25
- Pass[DAS-T3.7] Eq. 3.18 (peck) at σ′/p_a = 0.25 → C_N 1.47
- Pass[DAS-T3.7] Eq. 3.18 (peck) at σ′/p_a = 0.5 → C_N 1.23
- Pass[DAS-T3.7] Eq. 3.18 (peck) at σ′/p_a = 0.75 → C_N 1.1
- Pass[DAS-T3.7] Eq. 3.18 (peck) at σ′/p_a = 1 → C_N 1
- Pass[DAS-T3.7] Eq. 3.18 (peck) at σ′/p_a = 1.5 → C_N 0.87
- Pass[DAS-T3.7] Eq. 3.18 (peck) at σ′/p_a = 2 → C_N 0.77
- Pass[DAS-T3.7] Eq. 3.18 (peck) at σ′/p_a = 3 → C_N 0.63
- Pass[DAS-T3.7] Eq. 3.18 (peck) at σ′/p_a = 4 → C_N 0.54
- Pass[DAS-T3.7] Eqs. 3.19/3.20 (bazaraa) at σ′/p_a = 0.25 → C_N 2
- Pass[DAS-T3.7] Eqs. 3.19/3.20 (bazaraa) at σ′/p_a = 0.5 → C_N 1.33
- Pass[DAS-T3.7] Eqs. 3.19/3.20 (bazaraa) at σ′/p_a = 0.75 → C_N 1
- Pass[DAS-T3.7] Eqs. 3.19/3.20 (bazaraa) at σ′/p_a = 1 → C_N 0.94
- Pass[DAS-T3.7] Eqs. 3.19/3.20 (bazaraa) at σ′/p_a = 1.5 → C_N 0.84
- Pass[DAS-T3.7] Eqs. 3.19/3.20 (bazaraa) at σ′/p_a = 2 → C_N 0.76
- Pass[DAS-T3.7] Eqs. 3.19/3.20 (bazaraa) at σ′/p_a = 3 → C_N 0.65
- Pass[DAS-T3.7] Eqs. 3.19/3.20 (bazaraa) at σ′/p_a = 4 → C_N 0.55
- Pass[DAS-E3.1] (N1)60 at 1.5 m = 16
- Pass[DAS-E3.1] (N1)60 at 3 m = 10
- Pass[DAS-E3.1] (N1)60 at 4.5 m = 14
- Pass[DAS-E3.1] (N1)60 at 6 m = 14
- Pass[DAS-E3.1] (N1)60 at 7.5 m = 11
- Pass[DAS-P3.4 Eq. 3.13] (N1)60 at 1.5 m = 12
- Pass[DAS-P3.4 Eq. 3.13] (N1)60 at 3 m = 11
- Pass[DAS-P3.4 Eq. 3.13] (N1)60 at 4.5 m = 10
- Pass[DAS-P3.4 Eq. 3.13] (N1)60 at 6 m = 8
- Pass[DAS-P3.4 Eq. 3.13] (N1)60 at 7.5 m = 12
- Pass[DAS-P3.4 Eq. 3.13] (N1)60 at 9 m = 12
- Pass[DAS-P3.5 Eq. 3.14] (N1)60 at 1.5 m = 9
- Pass[DAS-P3.5 Eq. 3.14] (N1)60 at 3 m = 10
- Pass[DAS-P3.5 Eq. 3.14] (N1)60 at 4.5 m = 10
- Pass[DAS-P3.5 Eq. 3.14] (N1)60 at 6 m = 8
- Pass[DAS-P3.5 Eq. 3.14] (N1)60 at 7.5 m = 12
- Pass[DAS-P3.5 Eq. 3.14] (N1)60 at 9 m = 12
- Pass[KRAMER] Ex 6.6 (N1)60 at 1.2 m = 17.47
- Pass[KRAMER] Ex 6.6 (N1)60 at 2.2 m = 7.9
- Pass[KRAMER] Ex 6.6 (N1)60 at 3.2 m = 5.1
- Pass[KRAMER] Ex 6.6 (N1)60 at 4.2 m = 4.6
- Pass[KRAMER] Ex 6.6 (N1)60 at 5.2 m = 7
- Pass[KRAMER] Ex 6.6 (N1)60 at 6.2 m = 11.7
- Pass[KRAMER] Ex 6.6 (N1)60 at 7.2 m = 14.6
- Pass[KRAMER] Ex 6.6 (N1)60 at 8.2 m = 13.7
- Pass[KRAMER] Ex 6.6 (N1)60 at 9.2 m = 15.2
- Pass[KRAMER] Ex 6.6 (N1)60 at 10.2 m = 9.3
- Pass[KRAMER] Ex 6.6 (N1)60 at 11.2 m = 22.8
- Pass[KRAMER] Ex 6.6 (N1)60 at 12.2 m = 12.4
- Pass[KRAMER] Ex 6.6 (N1)60 at 13.2 m = 10.1
- Pass[KRAMER] Ex 6.6 (N1)60 at 14.2 m = 9.8
- Pass[KRAMER] Ex 6.6 (N1)60 at 15.2 m = 20.7
- Pass[KRAMER] Ex 6.6 (N1)60 at 16.2 m = 22.5
- Pass[KRAMER] Ex 6.6 (N1)60 at 17.2 m = 4.1
- Pass[KRAMER] Ex 6.6 (N1)60 at 18.2 m = 4.7
- Pass[KRAMER] Ex 6.6 (N1)60 at 19.2 m = 3.1
- Pass[KRAMER] Ex 6.6 (N1)60 at 20.2 m = 28.5
- Pass[BOWLES] Ex 3-2: N = 20, ER 80 %, 150 mm hole, p′o = 205 kPa, rod 12 m → N′60 = 19
- Pass[BOWLES] Ex 3-4: N = 20, ER 55 %, p′o = 100 kPa, 6 m hole → N′60 = 17
- Pass[GEC6] Eq. 4-1: N = 30 at ER 80 % → N60 = 40 (energy ratio only, = IS 2131:2025 §5.6.2)
- Pass[GEC6] App. B Ex 3: N′ at 1.5 m = 10
- Pass[GEC6] App. B Ex 3: N′ at 4.5 m = 10
- Pass[GEC6] App. B Ex 3: N′ at 7.5 m = 15
- Pass[GEC6] App. B Ex 3: N′ at 10.5 m = 20
- Pass[MNO12] App. A N60 at 1.1 m = 3.8
- Pass[MNO12] App. A N60 at 1.8 m = 5
- Pass[MNO12] App. A N60 at 2.6 m = 4.3
- Pass[MNO12] App. A N60 at 3.4 m = 6.4
- Pass[MNO12] App. A N60 at 4.1 m = 8.5
- Pass[MNO12] App. A N60 at 4.9 m = 10.7
- Pass[MNO12] App. A N60 at 5.6 m = 24.9
- Pass[MNO12] App. A N60 at 6.4 m = 21.4
- Pass[MNO12] App. A N60 at 7.2 m = 30.9
- Pass[MNO12] App. A N60 at 7.9 m = 23.8
- Pass[MNO12] App. A N60 at 9.4 m = 25
- Pass[MNO12] App. A N60 at 10.2 m = 13.8
- Pass[MNO12] App. A N60 at 11 m = 10
- Pass[MNO12] App. A N60 at 12.5 m = 5
- Pass[YOUD] Table 2: rod length 2.5 m → C_R = 0.75
- Pass[YOUD] Table 2: rod length 3.5 m → C_R = 0.8
- Pass[YOUD] Table 2: rod length 5 m → C_R = 0.85
- Pass[YOUD] Table 2: rod length 8 m → C_R = 0.95
- Pass[YOUD] Table 2: rod length 12 m → C_R = 1
- Pass[YOUD] Table 2: borehole 100 mm → C_B = 1
- Pass[YOUD] Table 2: borehole 150 mm → C_B = 1.05
- Pass[YOUD] Table 2: borehole 200 mm → C_B = 1.15
- Pass[IS2131] Fig. 3: σ′0 = 5 kPa → C_N ≈ 2
- Pass[IS2131] Fig. 3: σ′0 = 50 kPa → C_N ≈ 1.24
- Pass[IS2131] Fig. 3: σ′0 = 100 kPa → C_N ≈ 1
- Pass[IS2131] Fig. 3: σ′0 = 200 kPa → C_N ≈ 0.77
- Pass[IS2131] Fig. 3: σ′0 = 300 kPa → C_N ≈ 0.64
- Pass[IS2131] Fig. 3: σ′0 = 400 kPa → C_N ≈ 0.54
- Pass[IS2131] Fig. 3: σ′0 = 550 kPa → C_N ≈ 0.43
- Pass[IS2131] §5.6.3 bounds 0.40 ≤ C_N ≤ 2.0 and σ′0 at SPT depth + 0.30 m by default
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
spt-correlations-web-validationspt-correlations — published-value validation (the ≥20-value gate).47 passing
Analyses validated: spt-correlations
- Pass[IS6403] Fig. 1: N = 10 → φ ≈ 30.3°
- Pass[IS6403] Fig. 1: N = 20 → φ ≈ 33.2°
- Pass[IS6403] Fig. 1: N = 30 → φ ≈ 36°
- Pass[IS6403] Fig. 1: N = 40 → φ ≈ 38.6°
- Pass[IS6403] Fig. 1: N = 50 → φ ≈ 40.8°
- Pass[IS6403] Fig. 1: N = 60 → φ ≈ 42.6°
- Pass[IS6403] Fig. 1: N = 70 → φ ≈ 43.8°
- Pass[IS6403] Fig. 1 gives no value outside its plotted range (N < 10, N > 75) — none is invented
- Pass[FHWA] Table 8-1: N160 = 0 → φ 25–30°
- Pass[FHWA] Table 8-1: N160 = 4 → φ 27–32°
- Pass[FHWA] Table 8-1: N160 = 10 → φ 30–35°
- Pass[FHWA] Table 8-1: N160 = 30 → φ 35–40°
- Pass[FHWA] Table 8-1: N160 = 50 → φ 38–43°
- Pass[EC7-F1] Table F.1: (N1)60 = 3 → I_D = 15 %
- Pass[EC7-F1] Table F.1: (N1)60 = 8 → I_D = 35 %
- Pass[EC7-F1] Table F.1: (N1)60 = 25 → I_D = 65 %
- Pass[EC7-F1] Table F.1: (N1)60 = 42 → I_D = 85 %
- Pass[EC7-F1] Table F.1: (N1)60 = 58 → I_D = 100 %
- Pass[EC7-F1] F.1(4): fine sand N is read in the ratio 55:60 — (N1)60 = 22.92 fine ≡ 25 medium → I_D 65 %
- Pass[EC7-F3] Table F.3: fine_uniform, I_D 40 % → φ′ 34°
- Pass[EC7-F3] Table F.3: fine_uniform, I_D 60 % → φ′ 36°
- Pass[EC7-F3] Table F.3: fine_uniform, I_D 80 % → φ′ 39°
- Pass[EC7-F3] Table F.3: fine_uniform, I_D 100 % → φ′ 42°
- Pass[EC7-F3] Table F.3: medium_uniform, I_D 40 % → φ′ 36°
- Pass[EC7-F3] Table F.3: medium_well, I_D 60 % → φ′ 41°
- Pass[EC7-F3] Table F.3: medium_well, I_D 80 % → φ′ 43°
- Pass[EC7-F3] Table F.3: medium_uniform, I_D 100 % → φ′ 43°
- Pass[EC7-F3] Table F.3: coarse_uniform, I_D 40 % → φ′ 38°
- Pass[EC7-F3] Table F.3: coarse_well, I_D 60 % → φ′ 43°
- Pass[EC7-F3] Table F.3: coarse_well, I_D 80 % → φ′ 44°
- Pass[EC7-F3] Table F.3: coarse_well, I_D 100 % → φ′ 46°
- Pass[EC7-F3] no φ′ below the tabulated I_D = 40 % — none is invented
- Pass[DAS] Example 3.2: σ′v 25.95 kPa, N60 8 → φ′ 37.5°
- Pass[DAS] Example 3.2: σ′v 51.9 kPa, N60 7 → φ′ 33.8°
- Pass[DAS] Example 3.2: σ′v 77.85 kPa, N60 12 → φ′ 36.9°
- Pass[DAS] Example 3.2: σ′v 103.8 kPa, N60 14 → φ′ 36.7°
- Pass[DAS] Example 3.2: σ′v 129.75 kPa, N60 13 → φ′ 34.6°
- Pass[DAS] Eq. 3.29 table: N60 3 → φ′ 28°
- Pass[DAS] Eq. 3.29 table: N60 6 → φ′ 29°
- Pass[DAS] Eq. 3.29 table: N60 9 → φ′ 30°
- Pass[DAS] Eq. 3.29 table: N60 10 → φ′ 30°
- Passdesign_code routes: IS → Fig. 1, AASHTO → lower bound for silty sand, EC7 → Table F.3
- Passthe silty-sand cap is reported and caps ONLY the recommended value — N still moves the methods
- Passa code route outside its chart falls back to the envelope with a warning, never an invented value
- PassN > 50 is flagged: the √N correlations have no code support there
- Passσ′v is live: with field N60 it adds the Kulhawy-Mayne value
- Passthe 32° cap is OFF by default (2026-09-26): φ′ follows N, and a note says where local practice would cap it
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
supporting-outputs-web-validationsupporting-outputs-web-validation.test.ts7 passing
Analyses validated: asphalt-institute-design, basal-heave, faarfield-mix-cdf, hs-confined-settlement, hs-small, jpcp-iri, pressuremeter-menard, pvd-design, rock-slope-stability
- Passrock-slope-stability: FoS = resisting/driving exactly, and both forces respond correctly (7 anchors)
- Passbasal-heave: resisting pressure is N_c·s_u and the FoS is its ratio to γH + q (6 anchors)
- Passpvd-design: d_e = 1.05·s for a triangular grid and 1.128·s for a square one (5 anchors)
- Passhs-small: G_s ≥ G_t, both fall with strain, and the cut-off strain bounds them (6 anchors)
- Passhs-confined-settlement: the linear reference is Δσ·H/E_oed and the strain is its own ratio (6 anchors)
- PassMiner's rule holds where an engine reports damage contributions (asphalt, JPCP, FAARFIELD)
- Passpressuremeter-menard: total settlement is the sum of its spherical and deviatoric parts
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
vane-correction-web-validationrecords a differenceValidation for `vane-correction` — Bjerrum field-vane correction factor μ = 1.7 − 0.54·log10(PI), capped at 1.0 (`vane-correction.ts`).4 passing
Analyses validated: vane-correction
- PassLook Table 4.14: μ = 1.0 for PI < 20 %, then 0.9, 0.85, 0.75, 0.70, 0.70, 0.65, 0.65, 0.65 at PI 30…100
- PassDas Example 3.3 (a): Bjerrum λ = 1.7 − 0.54 log(32) applied to s_u(VST) = 20.12 kN/m² → 17.85 kN/m²
- PassCFEM §4.5.6 (Aas et al. 1986): the design μ never exceeds 1.0 — low-PI clays are capped, not raised
- Passcross-check: engine μ agrees with the independent Han (2015) Eq. 2.46 regression to ±0.03 for PI 40…100
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Reliability, back-analysis and design aids
0 finite-element rows · 0 closed-form problems · 3 validation suites
Cited validation suites
bayesian-back-analysis-web-validationObservational-method Bayesian back-analysis — CITED validation (≥20 values).11 passing
Analyses validated: bayesian-back-analysis
- Passbayesian-back-analysis: Φ⁻¹ credible-interval z-values [4]
- Passbayesian-back-analysis: conjugate single-obs update, exact closed form [1]
- Passbayesian-back-analysis: linear scale/offset observation [1]
- Passbayesian-back-analysis: vague prior, n i.i.d. → sample mean & σ²/n [2]
- Passbayesian-back-analysis: zero observations → posterior = prior [3]
- Passbayesian-back-analysis: strong prior barely moves [1]
- Passbayesian-back-analysis: precise observation dominates [1]
- Passbayesian-back-analysis: precisions add over observations; monotone tightening [1][2]
- Passbayesian-back-analysis: next-reading predictive widens by σ_obs [3]
- Passbayesian-back-analysis: guards non-finite & degenerate inputs
- Passbayesian-back-analysis: TOTAL cited assertions
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
design-copilot-web-validationValidation for the AI design copilot's deterministic core (`design-copilot.ts`).27 passing
Analyses validated: design-copilot, settlement
- Passbenchmark: Sphere → 0 at origin
- Passbenchmark: Rosenbrock → 0 at (1,1)
- Passbenchmark: Booth → 0 at (1,3)
- Passbenchmark: Matyas → 0 at origin
- Passbenchmark: Beale → 0 at (3,0.5)
- Passbenchmark: Himmelblau → 0
- Passbenchmark: McCormick → −1.9133
- Passbenchmark: Three-hump camel → 0 at origin
- Passbenchmark: Goldstein–Price → 3 at (0,−1)
- Passbenchmark: Bohachevsky → 0 at origin
- Passbenchmark: Lévi N.13 → 0 at (1,1)
- Passbenchmark: 4-D sphere → 0
- Passgolden-section: parabola min at 3
- Passgolden-section: quartic min at 2
- Passgolden-section: cosh min at 1
- Passsettlement: rigid circle = exact Timoshenko punch
- Passsettlement: square uses Iρ=0.82
- Passsettlement: strip uses Iρ=2.0
- Passfoundation: φ=0 clay net bearing ≈ 5.14·cu (Prandtl/Skempton)
- Passfoundation: sand FoS increases with width B
- Passfoundation: higher target FoS → larger B*
- Passfoundation: higher cohesion → smaller B* (clay)
- Passfoundation: settlement governs on low-E soil, constraint active (KKT)
- Passfoundation: bearing governs on stiff-weak soil, FoS active (KKT)
- Passfoundation: B* is the minimal feasible width
- Passoptimiser: smallestFeasible finds the monotone threshold
- Passoptimiser: gridMinimize yields samples covering the box
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
reliability-web-validationReliability kernel — web-sourced / textbook CITED validation (≥20 values).8 passing
Analyses validated: reliability
- Passreliability-web-validation: Φ(−β) matches the standard-normal table [2]
- Passreliability-web-validation: Φ⁻¹(p) matches the table [2]
- Passreliability-web-validation: linear normal R−S exact β [1][3]
- Passreliability-web-validation: lognormal R−S exact β; FORM invariance [1][3]
- Passreliability-web-validation: correlation changes β per Baecher & Christian [5]
- Passreliability-web-validation: Duncan 2000 / USACE β→P_f + bands [4]
- Passreliability-web-validation: FORM invariant where FOSM is not [3]
- Passreliability-web-validation: TOTAL cited assertions
The suite’s sources, tolerances and the values it deliberately does not assert are reproduced in the full manual.
Re-running a row yourself
Each finite-element row names the test that reproduces it and the input file it runs; each suite is one test file; the closed-form registry re-measures itself. The commands are in the full manual. A selection of closed-form rows can be re-run in this browser with a reproducible hash in the verification suite, and the row-by-row registries are on the verification registry page.
Run the same engines on your own design.
The analyses behind these benchmarks are the ones you run in a project. Start free and put your own numbers through them.